Larson Electronics EPL-QC-16C-2X50LED-RT-100 Manuale utente
Larson Electronics, LLC Phone: Fax: (903) 498-3364 www.larsonelectronics.com
1of 3
100W EXP LED Light - 14,000 Lm - Cart Mount - Quick Change
Mount - C1D1 - 100' 16/3 SOOW - GEN Plug
Instruction Manual
This explosion proof wheelbarrow light is designed for illumination of industrial locations. It uses the latest in
solid state lighting technology for long life, low maintenance and high efficiency.
The unique design focuses the light where it is needed, giving improved efficiency over a conventional HID
luminaire.
An internal, universal input, power-factor-corrected switch-mode supplyallowsit to be used from any
nominal120-277V AC 50/60Hz, stepped down to 12V DC, power supplywithout any variation in light
output.
WARNING
To avoidthe riskof fire,explosion or electric shock, this product should be installed, inspected and
maintained by a qualified electricianonly, in accordance with all applicableelectrical codes.
To avoidelectric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system with an equipment-grounding conductor.
To avoid explosion:
Make sure the supply voltage is within the luminaires’ voltage rating.
Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.
Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
The light fixture on this wheelbarrow cart is factory sealed.
CART OPERATION
The wheelbarrow cart assembly consists of 2 parts:
1. Light head
2. Wheelbarrow cart base
To assemble cart, insert light head over center hole of wheelbarrow cart and tighten hand screw. The
wheelbarrow cart is now ready for use.
Tilt cart using both handles and maneuver like a wheelbarrow. Simply roll entire assembly to a new location
once assembled. Make sure light head is secure prior to maneuvering cart.
WARNING: Be sure all hand screws are tight before transporting! Use caution when maneuvering near
inclines or drop offs.
Run power cord to a nearby compatible receptacle outputting voltage listed on product label.
WARNING: check nameplate for proper voltage. Damage from improper voltage may void warranty.
To adjust light head vertically, loosen hand screws on either side. Once desired angle is achieved, tighten
both hand screws to secure light in its place. Loosen the single hand screw holding light head to rotate
horizontally. Be sure all hand screws are tight before transporting!
EPL-QC-16C-2X50LED-RT-100
(877) 348-9680
Larson Electronics, LLC Phone: Fax: (903) 498-3364 www.larsonelectronics.com
2of 3
MOUNTING
The quick change mounting system allows for quick mount and dismount from the mounting base. To remove,
loosen the center collar towards the base of the mount to free the base in order to remove it from the cart.
Twist counter-clockwise until loose, lift collar and slide light head away from the base. Follow these steps in
reverse order for attaching light head.
WIRING (see attached wiring diagram)
This unit comes preconfigured with selected cord cap, color temperature, and beam angle. Once deployed,
plug cord cap into compatible receptacle.
Voltage: This explosion proof LED light is universal voltage capable and can be operated with
100-277V AC, 50/60 Hz without modifications to the fixture. A low voltage version of this LED
fixture that operates on AC/DC voltages from 11-25 volts is also available. 18-48V AC/DC voltage
models are available for network systems and marine vessels. We also offer an additional
347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED
light fixture.
Follow all applicable local, state, and National Electrical Code for the hazardous area!
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
EPL-QC-16C-2X50LED-RT-100
(877) 348-9680
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
EPL-QC-16C-2X50LED-RT-100
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT
1- FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Larson Electronics, LLC Phone: Fax: (903) 498-3364 www.larsonelectronics.com 3of 3
(877) 348-9680
877-348-9680
Indice
Altri manuali Larson Electronics Luce da lavoro
Larson Electronics
Larson Electronics GL-9900 Manuale
Larson Electronics
Larson Electronics EXPRL-98 Manuale utente
Larson Electronics
Larson Electronics EPL-FL-26 Manuale utente
Larson Electronics
Larson Electronics WL-LED-12-M Manuale utente
Larson Electronics
Larson Electronics AML-LED-WP40-M-22C Manuale
Larson Electronics
Larson Electronics EHL-LED-120X12V-XGFI Series Manuale utente
Larson Electronics
Larson Electronics EPL-16C-1MLED-300 Manuale utente
Larson Electronics
Larson Electronics WAL-QP-2X500LTL-LED-100 Manuale utente
Larson Electronics
Larson Electronics EPL-16C-1MLED Manuale utente
Larson Electronics
Larson Electronics EPL-BS-25WRE Manuale
Larson Electronics
Larson Electronics LED10W-1X2LT Manuale utente
Larson Electronics
Larson Electronics WAL-DL-60LED-M-GCR50-SP0002 Manuale utente
Larson Electronics
Larson Electronics EHL-LED-15W-50-HR Manuale utente
Larson Electronics
Larson Electronics WAL-TP-2X50E-1224 Manuale utente
Larson Electronics
Larson Electronics RSLED Manuale utente
Larson Electronics
Larson Electronics WAL-SBDL-WP60E-XX-1227 Manuale utente
Larson Electronics
Larson Electronics EPLC2-MB-100LED-100 Manuale utente
Larson Electronics
Larson Electronics LEDWP-250E-DLC-5000K Manuale
Larson Electronics
Larson Electronics WDL-12-IPS-LED-1227 Manuale utente
Larson Electronics
Larson Electronics WAL-BP-3XLED-CPR Manuale utente
