Larson Electronics WAL-BP-3XLED-CPR Manuale utente

WAL-BP-3XLED-CPR

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

108W Portable Emergency LED Light Tower

10,000 Lumens - USB Port & 12V Socket - 5.25' Tall Tower

Operation Manual

SETUP PROCEDURE

1. Lay case on ground and open lid.

2. Deploy legs by releasing latch and rotating leg out. Lift the locking pin for holding leg in place.

Once leg is aligned with locking pin, press pin down to engage.

3. Repeat for leg on opposite side.

4. Stand the light tower upright until it locks in place.

5. Loosen adjustment knob and rotate light head upwards.

6. Extend the light pole to the desired height by unlatching clips for each pole. Relatch clips to secure

each section.

7. Unfold the light head and position lens up for spot light and down for flood light in one area. For all

around lighting, fold the light head to its 360° scene light configuration.

8. Press the power button on the front to illuminate the light. 1st Press – Low Output, 2nd Press – Medium

Output, 3rd Press – High Output, 4th Press – Off.

9. Close the lid.

BREAKDOWN PROCEDURE

1. Turn light off by cycling through power button. (Additionally, light will automatically disengage once

folded into case.)

2. Fold and rotate light head downwards. Loosen adjustment screw and tighten.

3. Open lid.

4. Lower telescoping pole to its fully collapsed position.

5. Fold light tower assembly into case by depressing the pin toward the base of the mast to unlock it and

set it inside.

6. Release locking pin holding each leg and fold toward case.

7. Latch legs.

8. Close lid and the light tower is ready for transport.

CHARGING

•Orange Receptacle marked “Input” on side is used for line voltage charging. This can be via the

cigarette plug adapter or household 100-240V AC power supply. Connect either into Orange plug

connector and supply power to charge the battery.

POWERING

•A waterproof power button is located on the front to power the light. Next to the power button is a

gauge which displays the current battery levels.

DC POWER RECEPTACLE

•The light is equipped with 2 USB ports and a locking DC accessory receptacle, located toward the

center top of the case accessed from inside the box under the lid. Simply plug devices into these

ports for powering.

VEHICLE EXTERNAL POWER SOURCE

1. Attach DC power cord charger into the “Input” side of the light tower.

2. Plug the DC power cord into the DC accessory receptacle of your vehicle.

3. It is recommended that the vehicle be running during operation in this mode as it will drain the vehicle

battery. The light DC accessory receptacle is connected directly to the internal battery. NOTE:

WAL-BP-3XLED-CPR

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

Operating in this mode will recharge the light’s internal battery.

NOTICE: Because the light DC accessory receptacle is connected directly to the internal battery,

when not using this external source option, you can plug any accessory up to 8 amps, (i.e. laptops,

cell phone chargers of the light hand held units), into the receptacle and the light will provide power.

If the amperage rating is exceeded, a built in auto-reset circuit breaker automatically shuts power off

until the accessory overload is removed.

TO DISCONNECT AFTER USE:

1. Switch lights off.

2. Turn vehicle ignition off.

3. Disconnect the dual end DC power cord from the vehicle.

4. Disconnect the dual end DC power cord from the light by twisting the plug away from the lock

arrows and pulling.

UTILIZING AC POWER

•The light is equipped with a power receptacle located on the right hand side of the case.

•It can operate on either 110/240 Volt, 50/60 Hz power.

•This power receptacle is used for recharging the internal battery.

•It can also be used as a supplemental power source to the internal battery.

TO UTILIZE THIS AC INPUT OPTION

1. The “EXTERNAL INPUT/OUTPUT” switch should be switched to the off position.

2. Plug the side of the power cord into the power receptacle on the light.

3. Plug the other end into an AC wall outlet.

4. Turn the lights on.

5. When the internal battery has been depleted, the lights should be switched off and the unit

recharged or utilize one of the before mentioned external DC power input methods for

continued operation.

TO DISCONNECT AFTER USE

1. Turn the lights off.

2. Unplug the AC power cord from the AC wall outlet.

3. Unplug the AC power cord from the socket.

4. Recharge the light using AC power.

RECHARGE USING AC WALL OUTLET

1. The “EXTERNAL INPUT/OUTPUT” switch should be in the off position.

2. Plug the side of the power cord into the power receptacle on the light.

3. Plug the other end into an AC wall outlet. Recharging time is a factor of DoD.

4. It is recommended that the unit be charged at least 4 hours to condition the battery for next use.

NOTICE: The light is equipped with a digital DC volt meter that operates when the light is turned on. This

will display the current voltage level of the internal battery.

Indice

Altri manuali Larson Electronics Luce da lavoro

Larson Electronics

Larson Electronics EHL-LED-7W-25-1523 Manuale utente

Larson Electronics

Larson Electronics EPL-BS-25WRE Manuale

Larson Electronics

Larson Electronics EPL-FL-26 Manuale utente

Larson Electronics

Larson Electronics LEDP5W-12LT Manuale utente

Larson Electronics

Larson Electronics WAL-TP-2X50E-1224 Manuale utente

Larson Electronics

Larson Electronics EPL-BS-70LED-6XMB-150X12 Manuale

Larson Electronics

Larson Electronics EPL-PM-150LED-X24I-100 Manuale

Larson Electronics

Larson Electronics EPL-16C-1MLED-300 Manuale utente

Larson Electronics

Larson Electronics WAL-DL-60LED-M-GCR50-SP0002 Manuale utente

Larson Electronics

Larson Electronics GL-9900 Manuale

Larson Electronics

Larson Electronics WDL-12-IPS-LED-1227 Manuale utente

Larson Electronics

Larson Electronics EPL-16C-1MLED Manuale utente

Larson Electronics

Larson Electronics EHL-LED-120X12V-XGFI Series Manuale utente

Larson Electronics

Larson Electronics GNM-LEDWL-25W Manuale

Larson Electronics

Larson Electronics EPLC2-MB-100LED-100 Manuale utente

Larson Electronics

Larson Electronics LEDWP-600E-DLC-5000K Manuale utente

Larson Electronics

Larson Electronics L810 Manuale utente

Larson Electronics

Larson Electronics EPL-BS-150HPS Series Manuale

Larson Electronics

Larson Electronics WL-LED-12-M Manuale utente

Larson Electronics

Larson Electronics LED10W-1X2LT Manuale utente

Larson Electronics

Larson Electronics LEDWP-250E-DLC-5000K Manuale

Larson Electronics

Larson Electronics EXPRL-98 Manuale utente

Larson Electronics

Larson Electronics EHL-LED-15W-50-HR Manuale utente

Larson Electronics

Larson Electronics EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP Manuale utente

Manuali Luce da lavoro popolari di altre marche

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuale utente

RTRMAX

RTRMAX RTX1868 Manuale utente

FeinTech

FeinTech LAL00220 Manuale utente

Bunker Hill Security

Bunker Hill Security 64735 Manuale utente

Goobay

Goobay 30450 Manuale utente

REV Ritter

REV Ritter SPOT Manuale utente

Ignition

Ignition Stagepix Line 100 IP Manuale utente

SCANGRIP

SCANGRIP DUO CONNECT Manuale utente

Bosch

Bosch GLI 18 V Manuale utente

Bayco

Bayco SL-1514 Manuale utente

EUFAB

EUFAB SMD LED 8+1 Manuale utente

DeWalt

DeWalt DCL510 Manuale utente

PowerSmith

PowerSmith PWLD080T Manuale utente

MaxLite

MaxLite 73683 Manuale utente

Heitronic

Heitronic Trend 27867 Manuale utente

Monzana

Monzana Gore MZCL10 Manuale utente

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuale utente

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuale utente