Larson Electronics EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP Manuale utente

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

100W EXP LED Light - 14,000 Lm - Cart Mount - Quick Change

Mount - C1D1 - 100' 12/3 SOOW - Inline

Instruction Manual

This explosion proof wheelbarrow light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a conventional HID

luminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any

nominal 120-277V AC 50/60Hz, stepped down to 24V DC, power supply without any variation in light

output.

WARNING

To avoidthe riskof fire,explosion or electric shock, this product should be installed, inspected and

maintained by a qualified electrician only, in accordance with all applicableelectrical codes.

To avoidelectric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

The light fixture on this wheelbarrow cart is factory sealed.

CART OPERATION

The wheelbarrow cart assembly consists of 2 parts:

1. Light head

2. Wheelbarrow cart base

To assemble cart, insert light head over center hole of wheelbarrow cart and tighten hand screw. The

wheelbarrow cart is now ready for use.

Tilt cart using both handles and maneuver like a wheelbarrow. Simply roll entire assembly to a new location

once assembled. Make sure light head is secure prior to maneuvering cart.

WARNING: Be sure all hand screws are tight before transporting! Use caution when maneuvering near

inclines or drop offs.

Run power cord to a nearby receptacle outputting voltage listed on product label.

WARNING: check nameplate for proper voltage. Damage from improper voltage may void warranty.

To adjust light head vertically, loosen hand screws on either side. Once desired angle is achieved, tighten

both hand screws to secure light in its place. Loosen the single hand screw holding light head to rotate

horizontally. Be sure all hand screws are tight before transporting!

EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

MOUNTING

The quick change mounting system allows for quick mount and dismount from the mounting base. To remove,

loosen the center collar towards the base of the mount to free the base in order to remove it from the cart.

Twist counter-clockwise until loose, lift collar and slide light head away from the base. Follow these steps in

reverse order for attaching light head.

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected cord cap, color temperature, and beam angle. Once deployed,

plug cord cap into compatible receptacle.

Voltage: The C1D1 explosion proof step-down transformer installed in-line provides the ability to

automatically monitor and adjust input current to maintain the correct LED voltage levels

regardless of input levels across a specific range. These transformers can operate on current

ranging from 90 to 305V AC or 127 to 431V DC without any modifications necessary as a result.

This ability to sense and adjust input current also provides protection against voltage spikes and

drops that can occur in electrical systems which would otherwise result in burning up or premature

LED failure without it. The inline transformer then steps down the input voltage to 24V DC to

power the explosion proof light. We also offer an additional 347-480V high voltage, 125-250V DC,

and 0-10V dimmable versions of this explosion proof LED light fixture.

Follow all applicable local, state, and National Electrical Code for the hazardous area!

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE WILL

VOID WARRANTY.

EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

This explosion proof LED light fixture is field serviceable. All major internal components can be

purchased from Larson Electronics and installed by a licensed electrician with basic tools. With most

explosion proof fixtures, the fixture must be returned to the manufacturer for repair work, which

presents downtime and long turn around times for repair work. Larson Electronics addresses this issue

with the Iron X series with field serviceability, allowing operators to perform service work without having

to return the fixture to the manufacturer in the event of damage or failure.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER

INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT

1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 3of 3

Indice

Altri manuali Larson Electronics Luce da lavoro

Larson Electronics

Larson Electronics RL-85-LED-36W-CPR Manuale utente

Larson Electronics

Larson Electronics AML-LED-WP40-M-22C Manuale

Larson Electronics

Larson Electronics EPL-16C-1MLED Manuale utente

Larson Electronics

Larson Electronics LEDWP-600E-DLC-5000K Manuale utente

Larson Electronics

Larson Electronics EHL-LED-240X12V-50 Manuale utente

Larson Electronics

Larson Electronics WAL-SBDL-WP60E-XX-1227 Manuale utente

Larson Electronics

Larson Electronics EPLC2-MB-100LED-100 Manuale utente

Larson Electronics

Larson Electronics EPL-BS-150HPS Series Manuale

Larson Electronics

Larson Electronics GL-9900 Manuale

Larson Electronics

Larson Electronics EPL-PM-150LED-X24I-100 Manuale

Larson Electronics

Larson Electronics RSLED Manuale utente

Larson Electronics

Larson Electronics WAL-TP-2X50E-1224 Manuale utente

Larson Electronics

Larson Electronics EHL-LED-120X12V-XGFI Series Manuale utente

Larson Electronics

Larson Electronics EXPRL-98 Manuale utente

Larson Electronics

Larson Electronics WAL-DL-60LED-M-GCR50-SP0002 Manuale utente

Larson Electronics

Larson Electronics EHL-LED-7W-25-1523 Manuale utente

Larson Electronics

Larson Electronics WAL-QP8-WP60PM-GRC50 Manuale utente

Larson Electronics

Larson Electronics EPL-BS-70LED-6XMB-150X12 Manuale

Larson Electronics

Larson Electronics WL-LED-12-M Manuale utente

Larson Electronics

Larson Electronics WDL-12-IPS-LED-1227 Manuale utente

Larson Electronics

Larson Electronics WAL-WBC-500LTL-LED-100 Manuale utente

Larson Electronics

Larson Electronics EHL-LED-15W-50-HR Manuale utente

Larson Electronics

Larson Electronics WAL-QP-2X500LTL-LED-100 Manuale utente

Larson Electronics

Larson Electronics GNM-LEDWL-25W Manuale

Manuali Luce da lavoro popolari di altre marche

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuale utente

RTRMAX

RTRMAX RTX1868 Manuale utente

FeinTech

FeinTech LAL00220 Manuale utente

Bunker Hill Security

Bunker Hill Security 64735 Manuale utente

Goobay

Goobay 30450 Manuale utente

REV Ritter

REV Ritter SPOT Manuale utente

Ignition

Ignition Stagepix Line 100 IP Manuale utente

SCANGRIP

SCANGRIP DUO CONNECT Manuale utente

Bosch

Bosch GLI 18 V Manuale utente

Bayco

Bayco SL-1514 Manuale utente

EUFAB

EUFAB SMD LED 8+1 Manuale utente

DeWalt

DeWalt DCL510 Manuale utente

PowerSmith

PowerSmith PWLD080T Manuale utente

MaxLite

MaxLite 73683 Manuale utente

Heitronic

Heitronic Trend 27867 Manuale utente

Monzana

Monzana Gore MZCL10 Manuale utente

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuale utente

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuale utente