Lightolier Lytecaster 1100F Series Manuale utente

NEW CONSTRUCTION

1. FRAME-IN (FIG. A)

WOOD JOIST/METAL STUD CONSTRUCTION (FIG. E): Line up bot-

tom edge of ADJUSTABLE MOUNTING BAR with bottom of wood joist.

Fasten MOUNTING FRAME to

wood joist by nailing MOUNTING BAR

TAB or nail into joist.

SUSPENDED GRID CEILING (FIG. G):

Position notched area of ADJUSTABLE MOUNTING BARS on top of T-

BAR for proper spacing to finished ceiling. Lock MOUNTING BARS by

bending TAB underneath T-BAR BEAD (Fig. G1). For round T-BAR BEAD,

use screws to lock MOUNTING BARS (Fig. G2).

WIRE TO SUPPLY LEADS:

For cable, use built-in cable clamp in J-Box. Connect white fixture

leads to neutral (white) supply leads. Black fixture leads to hot (black)

supply leads. Bare fixture wire to supply ground. Use wirenuts (local

hardware item). Place all electrical connections in the J-Box, attach J-

Box cover.

NOTE: ADJUSTABLE MOUNTING BARS are pre-assembled on long side of

MOUNTING FRAME for rigidity and ease of installation (Fig. E).

MOUNTING BARS must be removed and installed on narrow side of

MOUNTING FRAME if installing in 16” joist spacing (Fig. F).

MOUNTING BARS can be extended to 24”. The MOUNTING FRAME

can be mounted off-center.

For suspended ceilings, make certain that bottom of MOUNTING

FRAME is no higher than 1” above finished ceiling (Fig. G).

2. CLOSE-IN (FIG. B)

Install plasterboard or other dry type ceiling. Hole in board can be cut

either on floor or after the board is secured in the ceiling. Use MOUNT-

ING FRAME opening as cutting guide template for hole – make sure

ROTO CLIPS are rotated out of hole area.

NOTE: For wet plaster ceiling, use Plaster Ring Accessory No. 1961 - order

separately.

3. SNAP-ON (FIG. C) See separate instruction sheet

4. PUSH-UP (FIG. D) for your choice of reflector trim.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:1100F

D0605 Page 1of 2

Installation of Lytecaster®Frame-in-Kit 1100F Series

WARNING – (RISK OF FIRE) Do not install insulation within 3 inches of fixture sides or wiring

compartments, nor above fixture in such a manner as to entrap heat.

LOCKING SCREW

LINE UP BOTTOM

EDGE WITH BOTTOM

OF WOOD JOIST

MOUNTING FRAME

CENTERING SLOTS

ADJUSTABLE

MOUNTING BARS

T-BAR

1" MAX

1-1/2" MAX.

G1 G2

Fig. G

Fig. E

ADJUSTABLE MOUNTING BARS MOUNTING FRAME

(NARROW SIDE)

LINE UP BOTTOM EDGE WITH

BOTTOM OF WOOD JOIST

Fig. F

ADJUSTABLE MOUNTING BARS

Fig. A

1. Frame-In Fig. B

2. Close-in Fig. C

3. Snap-On Fig. D

4. Push-Up

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:1100F

D0605 PAGE 2OF 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

MOUNTING FRAME

BRIDGE

SLOT

Fig. H

ROTO CLIP

STAPLE

MOUNTING FRAME

CEILING MATERIAL

Fig. I

FRAME

J-BOX COVER

J-BOX

J-BOX SPRING

J-BOX COVER

Fig. J

BALLAST REPLACEMENT (FIG. J)

NOTE: Ballast replacement must be provided by a “qualified electrician”.

1. TURN OFF POWER.

2. Remove reflector trim from FRAME-IN KIT.

3. Remove J-BOX COVER nearest ceiling opening by lifting SPRING.

4. Disconnect all input wiring to ballast.

5. Remove BALLAST ASSEMBLY from J-BOX by pulling SPRING upward

(Fig. J).

6. Remove BALLAST ASSEMBLY through ceiling opening.

7. Release all wires from BALLAST WIRE CONNECTORS by inserting small

blade tool, with insulated handle, into WIRE RELEASE SLOTS. (Fig K).

NOTE: Replacement ballast kits generally are supplied with this special

wire release tool.

8. Remove (2) NUTS which hold BALLAST to J-BOX COVER.

9. Replace old BALLAST with new BALLAST and attach with NUTS

to J-BOX COVER.

10.Reassemble new BALLAST ASSEMBLY to J-BOX by snapping

onto J-BOX spring (Fig. J).

11.Rewire fixture. See WIRING DIAGRAM on BALLAST LABEL.

EXISTING CONSTRUCTION

Fig. A

1. Cut-Opening Fig. B

2. Wire-in Fig. C

3. Put Through Fig. D

4. Anchor Fig. F

6. Push-up

Fig. E

5. Snap-on

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

REMOVE

INSERT

BALLAST WIRE

CONNECTORS

WIRE RELEASE

BLADE

(BY OTHERS)

WIRE RELEASE

SLOTS

1. CUT OPENING (FIG. A AND FIG H)

a. Remove ADJUSTABLE MOUNTING BARS.

b. Use MOUNTING FRAME opening as template.

c. Break off BRIDGE on MOUNTING FRAME as shown in

Fig. H by breaking WEBS on SLOTS with cutting plier.

2. WIRE-IN (FIG. B)

For cable, use built in Cable Clamp in J-BOX. Connect white fixture

lead to neutral (white) supply lead. Black fixture leads to hot (black)

supply lead. Bare copper and/or green insulated wire(s) must all be

connected to supply ground. Use wire nuts (local hardware items).

Place all electrical connections in the

J-BOX. Attach J-BOX COVER onto J-BOX.

3. PUT THROUGH (FIG. C AND FIG. J)

Detach BALLAST ASSEMBLY from J-BOX and pass MOUNTING

FRAME into ceiling as shown in Fig. C. Reattach BALLAST ASSEMBLY.

4. ANCHOR (FIG. D AND FIG. I)

Using STAPLE (order separately Cat. #1985S), slide long end under-

neath raised embossing and short leg into ceiling (Fig. I).

5. SNAP-ON (FIG. E) See separate instruction sheet

6. PUSH-UP (FIG. F) for your choice of reflector trim.

Altri manuali Lightolier Apparecchio di illuminazione

Lightolier

Lightolier ProSpec 26030W Manuale utente

Lightolier

Lightolier Calculite 7790QD Manuale utente

Lightolier

Lightolier Lytecaster 1179M1 Manuale utente

Lightolier

Lightolier SC4WC232 Manuale utente

Lightolier

Lightolier Calculite C4P20D Manuale utente

Lightolier

Lightolier Calculite ProSpec PB3A7050 Manuale utente

Lightolier

Lightolier ProSpec 26690 Manuale utente

Lightolier

Lightolier Calculite ProSpec PA1P3075 Manuale utente

Lightolier

Lightolier Lytespan 8640WH Manuale utente

Lightolier

Lightolier KD SERIES HO Manuale utente

Lightolier

Lightolier Lytecaster 302ESX Manuale utente

Lightolier

Lightolier 40600H1 Guida

Lightolier

Lightolier TE Series Manuale utente

Lightolier

Lightolier Alter Dome QVC2GPFOS1FT Manuale utente

Lightolier

Lightolier QVH2GPFOS2FT Manuale utente

Lightolier

Lightolier 6700MS22U Manuale utente

Lightolier

Lightolier Calculite LW7/PLW7P38D Manuale utente

Lightolier

Lightolier Calculite ProSpec PA3A7050 Manuale utente

Lightolier

Lightolier Md.Coffer MDCGWSVA2SB4SB Manuale utente

Lightolier

Lightolier Brisa FP14U Manuale utente

Lightolier

Lightolier IS-CWLPC120 Manuale utente

Lightolier

Lightolier PENDALYTE SERIES Istruzioni per l’uso

Lightolier

Lightolier CDS2GPF214 Manuale utente

Lightolier

Lightolier ProSpec 26070 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

ArtFox

ArtFox Beam 15R extreme Manuale utente

GLG

GLG multispot 330 Manuale utente

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuale utente

SELF Electronics

SELF Electronics FLEX Manuale utente