Lippert Components OneControl Hotspot Manuale utente
OneControl® Hotspot™
(Prepped)
OEM INSTALLATION MANUAL
Rev: 01.15.20 Page 2 CCD-0002221
TABLE OF CONTENTS
Introduction 2
Safety 2
Resources Required 3
Preparation 3
Installation 3
Notes 9
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death
or serious personal injury if not performed safely and within the parameters set forth in this manual.
Failure to follow instructions provided in this manual may result in serious personal injury and/or
severe product and property damage, including voiding of the component warranty.
Unit MUST be supported per manufacturer's recommendations before working underneath. Failure
to do so may result in death or serious personal injury.
Always wear eye protection when performing service, maintenance or installation procedures.
Other safety equipment to consider would be hearing protection, gloves and possibly a full face
shield, depending on the nature of the task.
The "CAUTION" symbol above is a sign that a procedure has a safety risk involved and may cause
personal injury, product or unit damage if not performed safely and within the parameters set forth
in this manual.
Introduction
This document provides instructions for the installation of an OneControl HotspotTM prep kit. The installed
kit is intended as an optional upgrade for RV owners.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage.
For information on the assembly or individual components of this product, please visit
https://support.lci1.com/electronics
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Rev: 01.15.20 Page 3 CCD-0002221
Moving parts can pinch, crush or cut. Keep clear and use caution.
Resources Required
Fig. 1
A
• 1-2 people, depending on the task
• Cordless or electric drill or screw gun
• Appropriate drill bits
• Appropriate drive bits
• Sharp cutting tool
• All weather silicone sealant
• Tape measure
• Straightedge
• Non-permanent marking method
• Strain reliefs for electrical wire
• Four #8 x ¾" stainless steel Phillips pan head screws
Preparation
1. Make sure unit is supported in accordance with manufacturer's recommendations.
2. Make sure the mounting surfaces for the internal prep plate (Fig. 1A) and external cellular antenna
prep plate (Fig. 1B) are flat and clean—free of dust, grime and oils.
Installation
NOTE: Orange lines indicate where material is being removed, either by cutting, grinding or some other
method. Green lines indicate a designated area. White lines with black borders indicate where
marking on an object with a permanent or non-permanent marking method is required.
B
C
Rev: 01.15.20 Page 4 CCD-0002221
1. Locate an area within the unit where the internal prep plate (Fig. 1A) can best be mounted.
NOTE: Keep in mind when installing the internal prep plate that the future install of the Hotspot system
will need to be installed on a flat surface area and be located within 12" of the internal prep plate.
2. If desired, create a template out of durable material, and similar to the dimensions specified in figure 2,
for the installation location of the internal prep plate.
NOTE: Dimensions subject to change.
3. Place the internal prep plate template flat and level against the designated mounting location to:
A. Mark the center of the three ⁄" diameter holes (Fig. 2).
B. Set the drill template aside.
C. Drill one 1 ⁄" diameter access hole through the center hole (Fig. 2).
Fig. 2
2 ¾"
4 ½"
⁄" Dia.
1 ⁄" Dia.
⁄" Dia.
Rev: 01.15.20 Page 5 CCD-0002221
4. Loosely place the internal prep plate assembly (Fig. 3) into the access hole.
A. Connect the electrical wires of the DC jack harness (Fig. 3A) to the power and ground circuitry.
B. Let the internal prep plate and DC jack harness lay loose across the access hole.
5. Position the external cellular antenna prep plate (Fig. 4) in the desired mounting location on the roof of
the unit, close to the approximate location to where the internal prep plate (Fig. 3) is located.
A. Make sure the external cellular antenna prep plate can lay flat against the roof's surface.
B. With a non-permanent marking method, trace an outline along the outer lip of the external cellular
antenna prep plate (Fig. 4A) on the roof's surface. Set the external cellular antenna prep plate aside
for future installation.
C. Using the point of the hole (Fig. 4B) where the coaxial cables will rest, as the starting point,
measure to the middle right side of the of the external cellular antenna prep plate. The
measurement should be approximately 8".
D. Measure and mark the same distance in step 5C on the trace outline of the roof's surface.
Measure from the middle right side in towards the center, mark the location on the roof's surface.
E. Using the point of the hole (Fig. 4B) where the coaxial cables will rest, as the starting point,
measure to the bottom side of the of the external cellular antenna prep plate. The measurement
should be approximately 3 3/4".
Fig. 4
Fig. 3
A
A
3 ¾"
8"
B
Rev: 01.15.20 Page 6 CCD-0002221
8. Place one end of each coaxial cable (Fig. 6A) to the hole of the external cellular antenna prep plate
(Fig. 6B) and slide the wires (Fig. 6C) into the far end of the slot area (Fig. 6D) to keep the wires in place.
AB
Fig. 5
F. Measure and mark the same distance in step 5E on the trace outline of the roof's surface.
Measure from the bottom side up towards the center, mark the location on the roof's surface.
6. Before any cuts are made to the roof of the unit:
A. Make sure the supplied coaxial cables will reach from the roof antenna's marked location to the
internal prep plate.
B. Make sure that there are no wires, pipes or tubing underneath the marked areas before cutting
and drilling.
7. Using the center point of the intersecting lines (Fig. 4B), use a sharp cutting tool to crosscut the rubber
roof 3/4"in each direction (Fig. 5A—orange lines).
A. Peel the corners of the rubber roof back.
B. Drill a 1/2" inch hole (Fig. 5B—orange circle) at the center of the cuts. This is the cellular antenna
coaxial cable access hole for passing the cables through the unit to the internal prep plate.
Fig. 6
AB
D
C
Rev: 01.15.20 Page 7 CCD-0002221
9. Apply all-weather silicone sealant (Fig. 7A—green line) to the underside of the external cellular
antenna prep plate, around the entire outer lip. Do not leave any gaps in the sealant to ensure a good
seal to the mounting surface.
Fig. 7
10. Thread the opposite ends of the cables through the drilled access hole in the roof. Carefully guide
the coaxial cables through the hole as the external cellular antenna prep plate is gently placed
onto the roof.
11. After the external cellular antenna prep plate is in place, use four #8 x ¾” stainless steel Phillips pan
head screws (Fig. 8A) to secure the external cellular antenna prep plate to the roof. Do not over-tighten
the screws.
NOTE: The silicone sealant will spread out slightly as the tightening of the screws draw down the external
cellular antenna prep plate.
12. An additional, continuous bead of all-weather silicone sealant should be placed around the outer lip
of the external cellular antenna prep plate (Fig. 9A—green line) and over the four mounting screws to
form a watertight seal. Allow silicone sealant to dry completely.
NOTE: DO NOT place silicone sealant on the top removeable lid or screws (Fig. 9B) of the external cellular
antenna prep plate. The gasket underneath the lid of the external cellular antenna prep plate
effectively makes the external cellular antenna prep plate waterproof and ready for easy future
installation of the external cellular antenna.
A
Fig. 8
A
A
A
A
Fig. 9
A
B
Rev: 01.15.20 Page 8 CCD-0002221
15. Place any excess coaxial cable into the area behind the internal prep plate. Secure excess cabling with
strain reliefs.
16. Place the internal prep plate flush against the wall, taking care to align the plate's two mounting holes
with the previously marked screw locations.
17. Install two #8 x ¾” stainless steel Phillips pan head screws (Fig. 11A) to secure the internal prep plate
to the wall.
A
Fig. 11
A
A
13. Feed the two cellular antenna coaxial cables through the unit and into the internal prep plate access hole.
14. Attach each coaxial cable to a coaxial bulkhead connector located on the back of the internal prep
plate (Fig. 10A).
A
Fig. 10
Installed DC Jack Harness not shown for clarity.
Rev: 01.15.20 Page 9 CCD-0002221
Notes
The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).
LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.
The information contained in this manual is subject to change without notice and at the sole discretion of LCI.
Revised editions are available for free download from lci1.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Altri manuali per OneControl Hotspot
1
Indice
Altri manuali Lippert Components Accessori per automobili
Lippert Components
Lippert Components ground control 3.0 Guida
Lippert Components
Lippert Components Kwikee Manuale utente
Lippert Components
Lippert Components Kwikee Revolution Step Series Manuale utente
Lippert Components
Lippert Components SolidStep Istruzioni per l'installazione
Lippert Components
Lippert Components SolidStep XF Manuale utente
Lippert Components
Lippert Components SOLERA SLIDER Manuale utente
Lippert Components
Lippert Components Curt Rota-Flex Pin Box Manuale utente
Lippert Components
Lippert Components Air Ride 155925 Istruzioni per l'installazione
Lippert Components
Lippert Components SolidStep 3.0 Premium Step Manuale utente
Lippert Components
Lippert Components In-Wall Slide-Out Manuale utente
Lippert Components
Lippert Components Vela Manuale utente
Lippert Components
Lippert Components Solera Classic Istruzioni operative e di manutenzione
Lippert Components
Lippert Components Solera Power Awning Regal Head Manuale per l'uso e la cura
Lippert Components
Lippert Components In-Wall Slide-Out Winnebago Istruzioni operative
Lippert Components
Lippert Components Ground Control 3.0 Landing Gear Manuale utente
Lippert Components
Lippert Components Tire Linc Manuale utente
Lippert Components
Lippert Components Solera Manuale utente
Lippert Components
Lippert Components Sway Command Manuale
Lippert Components
Lippert Components Jack-It Manuale utente
Lippert Components
Lippert Components Edge Manuale utente
Lippert Components
Lippert Components A-Frame Coupler Istruzioni per l'installazione
Lippert Components
Lippert Components Alumi-Tread series Manuale utente
Lippert Components
Lippert Components Levelegs Manuale del proprietario
Lippert Components
Lippert Components ground control TT Istruzioni per l'installazione
