LS ELECTRIC XGT Series Manuale utente

Programmable Logic Control

XGB Main unit(XBC-U Type)

XBC

-DN32U(/DC)

XBC

-DN32UP(/DC)

XBC

-DN32UA (/DC)

XBC

-DP32U(/DC)

XBC

-DP32UP(/DC)

XBC

-DP32UA(/DC)

XBC

-DR28U(/DC)

XBC

-DR28UP(/DC)

XBC

-DR28UA(/DC)

XGT Series

Safety Instruction

Before using the product …

For your safety and effective operation, please read the safety instructions

thoroughly before using the product.

►Safety Instructions should always be observed in order to prevent accident

or risk with the safe and proper use the product.

►Instructions are separated into “Warning” and “Caution”, and the meaning of

the terms is as follows;

Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury

Indicates a potentially hazardous situation which,if

not avoided, may result in minor or moderate injury.

It may also be used to alert against unsafe practices

►The marks displayed on the product and in the user’s manual have the

following meanings.

Be careful! Danger may be expected.

Be careful! Electric shock may occur.

►The user’s manual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instruction

Safety Instructions when designing

Please, install protection circuit on the exterior of PLC to protect

the whole control system from any error in external power or PLC

module. Any abnormal output or operation may cause serious problem

in safety of the whole system.

- Install applicable protection unit on the exterior of PLC to protect

the system from physical

damage such as emergent stop switch,

protection circuit, the upper/lowest limit switch, forward/reverse

operation interlock circuit, etc.

- If any system error (watch-dog timer error, module installation error,

etc.) is detected during CPU operation in PLC, the whole output is

designed to be turned off and stopped for system safety. However,

in case CPU error if caused on output device itself such as relay or

TR can not be

detected, the output may be kept on, which may

cause serious problems. Thus, you are recommended to install an

addition circuit to monitor the output status.

Never connect the overload than rated to the output module nor

allow the output circuit to have a short circuit, which may cause a

fire.

Never let the external power of the output circuit be designed to

be On earlier than PLC power, which may cause abnormal output or

operation.



In case of data exchange between computer or other external

equipment and PLC through communication or any operation of

PLC (e.g. operation mode change), please install interlock in the

sequence program to protect the system from any error. If not, it

may cause abnormal output or operation.

Warning

Safety Instruction

Safety Instructions when designing

I/O signal or communication line shall be wired at least 100mm

away from a high-voltage cable or power line.If not, it may cause

abnormal output or operation.

Caution

Use PLC only in the environment specified in PLC manual or

general standard of data sheet. If not, electric shock, fire, abnormal

operation of the product or flames may be caused.

Before installing the module, be sure PLC power is off. If not,

electric shock or damage on the product may be caused.

Be sure that each module of PLC is correctly secured. If the

product is installed loosely or incorrectly, abnormal operation, error or

dropping may be caused.

Be sure that I/O or extension connecter is correctly secured. If

not, electric shock, fire or abnormal operation may be caused.

If lots of vibration is expected in the installation environment,

don’t let PLC directly vibrated. Electric shock, fire or abnormal

operation may be caused.

Don’t let any metallic foreign materials inside the product, which

may cause electric shock, fire or abnormal operation..

Caution

Safety Instruction

Safety Instructions when wiring

Prior to wiring, be sure that p

ower of PLC and external power is

turned off. If not, electric shock or

damage on the product may be

caused.



Before PLC system is powered on, be sure that all the covers of

the terminal are securely closed. If not, electric shock may be caused

Warning



Let the wiring installed correctly after checking the voltage rated

of each product and the arrangement of terminals. If not, fire,

electric shock or abnormal operation may be caused.

Secure the screws of terminals tightly with specified torque when

wiring. If the screws of terminals get loose, short circuit, fire or abnormal

operation may be caused.

Surely use the ground wire of Class 3 for FG terminals, which is

exclusively used for PLC. If the terminals not grounded correctly,

abnormal operation may be caused.

Don’t let any foreign materials such as wiring waste inside the

module while wiring, which may cause fire, damage on the product

or abnormal operation.

Caution

Safety Instruction

Safety Instructions for test-operation or repair

Safety Instructions for waste disposal

Don’t touch the terminal when powered. Electric shock or abnormal

operation may occur.

Prior to cleaning or tightening the terminal screws, let all the

external power off including PLC power.

If not, electric shock or

abnormal operation may occur.

Don’t let the battery recharged, disassembled, heated, short or

soldered. Heat, explosion or ignition may cause injuries or fire.

Warning

Don’t remove PCB from the module case nor remodel the module.

Fire,electric shock or abnormal operation may occur.

Prior to installing or disassembling the module, let all the external

power off including PLC power. If not, electric shock or abnormal

operation may occur.

Keep any wireless installations or cell phone at least 30cm away

from PLC. If not, abnormal operation may be caused.

Caution



Product or battery waste shall be processed as industrial waste.

The waste may discharge toxic materials or explode itself.

Caution

Revision History

Version

Date Remark Part Page

V 1.0 2015.5 1. First Edition -

V1.1 2015.7

1.source output PLC added(XBC-DPxxU(A)(P))

2.DC power PLC added(/DC)

3.PID bumpless added

-_PID_MV_BMPL flag comment modified

4.Web server download modified

-2) communication setup

-3.5 Improvement of the web server’s speed

5.Internal Input/output circuit & TB modified

6.deviec&flag modified

(1) web server flag added

(2) Timer flag added

(3) N Device Notice modified(cannot write)

App

Front

2-1~4,3-6

Front

3-5

6-20

3-20~21

3-69~71

3-5~7

3-11

App 1-2

App 1-10

V1.2 2019.8

1. user CAM modified

- When the User CAM is operating, changing

User CAM is available in continuous operation

2. Module added

- XBE-DN32A

3. PWM output err added(2ms)

4. Added explanation about compilation method

differences

5. High speed counter clear function added

6. Add OS update function using SD card

7. Built-in FEnet 16 channel function added

8. Add auto assignment function

9. Smart server function added

App

8-125

3-25, 3-27

6-12

3-10

4-21

App 5-1

1-3~4, 15

3-10

1-36

Revision History

10. Add PLC uptime flag

11. PID differential calculation source parameter

added

App

App 1-5

6-20

V1.3 2020.06 1. Company name changed - -

About User’s Manual

Congratulations on purchasing PLC of LS ELECTRIC Co.,Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions,

performances, installation and programming of the product you purchased in order for correct

use and importantly, let the end user and maintenance administrator to be provided with the

User’s Manual.

The Use’s Manual describes the product. If necessary, you may refer to the following description

and order accordingly. In addition, you may connect our website(http://www.lselectric.co.kr/)and

download the information as a PDF file.

Relevant User’s Manual

Title Description No. of User

Manual

XG5000 User’s

Manual

It describes how to use XG5000 software especially

about online functions such as programming,

printing, monitoring and debugging by using XGT

series products.

10310000512

XGK/XGB Series

Instruction &

Programming

It describes how to use the instructions for

programming using XGK/XGB series.

10310000510

XBC

Ultimate Performance

XGB Unit

It describes how to use XGB main unit, system

configuration, mechanism ,program

function ,input/output function, Built-in High-speed

Counter, Datalog, PID Control, Built-in

Communication function, Built-in Position, Built-in

Analog input/output.

10310001374

XGB Analog

User’s Manual

It describes how to use the specification of analog

input/analog output/temperature input module,

system configuration and built-

in PID control for

XGB main unit.

10310000920

XGB Position

User’s Manual

It describes how to use built-in Position function for

XGB main unit.

10310000927

XGB Cnet I/F

User’s Manual

It describes how to use built-in communication

function for XGB main unit and external Cnet I/F

module.

10310000816

XGB Fast Ethernet I/F

User’s Manual

It describes how to use XGB FEnet I/F module.

10310000873

CANopen

Commnunication

Module

It describes how to use XGB CANopen

Commnunication Module

0310001245

EtherNet/IP

Commnunication

Module

It describes how to use XGB EtherNet/IP

Communication module

10310001159

About User’s Manual

XGB Profibus-DP I/F

(Master) User’s

Manaual

It describes how to use XGB Profibus-DP I/F

(Master) Commnunication Module 10310001310

XGB Profibus-DP I/F

(Slave) User’s

Manaual

It describes how to use XGB Profibus-DP I/F

(Slave) Commnunication Module 10310001410

XGB DeviceNet I/F

(Slave) User’s

Manaual

It describes how to use XGB DeviceNet I/F

(Slave) Commnunication Module 10310001414

XGB High speed

counter module User’s

Manual

It describes how to use High speed counter(XBF-

HO02A, XBF-HD02A) 10310001240

Altri manuali per XGT Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LS ELECTRIC Unità di controllo

LS ELECTRIC

LS ELECTRIC S100 Manuale utente

LS ELECTRIC

LS ELECTRIC CANopen LSLV-G100 Series Manuale utente

LS ELECTRIC

LS ELECTRIC SV-iS7 Series Manuale utente

LS ELECTRIC

LS ELECTRIC LSLV-S100 Series Manuale utente