LSIS XBL-EIPT Manuale utente

Right choice for ultimate yield

LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.

Programmable Logic Controller

XGB Ethernet/IP IF Module

User’s Manual



Read this manual carefully before

installing,

wiring, operating, servicing

or inspecting this equipment.



Keep this manual within easy reach

for quick reference.

XBL-EIPT

XGT Series

http://www.lsis.com

Safety Instruction

Before using the product …

For your safety and effective operation, please read the safety instructionsthoroughly before using the product.

►Safety Instructions should always be observed in order to prevent accident or risk with the safe and

proper use the product.

►Instructions are divided into “Warning” and “Caution”, and themeaning of the terms is as follows.

This symbol indicates the possibility of serious injury or death if some applicable

instruction is violated

This symbol indicates the possibility of severe or slight injury, and property

damages if some applicable instruction is violated

Moreover, even classified events under its caution category may develop into serious accidents relying on

situations.Therefore we strongly advise users toobserve all precautions properly just like warnings.

►The marks displayed on the productand in the user’s manual have the following meanings.

Be careful! Dangermay be expected.

Be careful! Electric shock may occur.

►The user’smanual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instruction

Safety Instructions for design process

Please install a protection circuit on the exterior of PLC so that the whole system may

operate safely regardless of failures from external power or PLC. Any abnormal output or

operation from PLC may cause seriousproblems to safety in whole system.

- Install protection units on the exterior of PLC like an interlock circuit that deals with opposite

operations such as emergency stop, protection circuit, and forward/reverse rotation or install an

interlock circuit that deals with high/low limit under its position controls.

- If any system error (watch-dog timer error, module installation error, etc.) is detected during

CPU operation in PLC, all output signals are designed to be turned off and stopped for safety.

However, there are cases when output signals remain active due to device failures in Relay and

TR which can’t be detected. Thus, you are recommended to install an addition circuit to monitor

the output status for those critical outputs which may cause significant problems.

Never overload more than rated current of output module nor allow to have a short circuit.

Over current for a long period time maycause a fire .

Never let the external power of the output circuit to be on earlier than PLC power, which may

cause accidents from abnormal output oroperation.

Please install interlock circuits in the sequence program for safe operations in the system

when exchange data with PLC or modify operation modes using a

computer or other

external equipments

Read specific instructions thoroughly when conducting control operations

with PLC.

Warning

Safety Instruction

Safety Instructions for design process

Safety Instructions on installation process

I/O signal or communication line shall be wired at least 100mm away from a high-voltage

cable or power line.Fail to follow this

Caution

Use PLC only in the environment specified in PLC manual or general standard of data

sheet. If not, electric shock, fire, abnormal operation of the product may be caused.

Before install or remove the module, be sure PLC power is off. If not, electric shock or damage

on the product maybe caused.

Be sure that every module is securely attached after adding a module or an extension

connector.If the product is installed loosely or incorrectly, abnormal operation, error or dropping

may be caused. In addit

ion, contact failures under poor cable installation will be causing

malfunctions as well.

Be sure that screws get tighten securely under vibrating environments. Fail to do so will put

the product under direct vibrations which will cause electric shock, fire and abnormal operation.

Do not come in contact with conducting parts in each module, which may cause electric

shock, malfunctions or abnormal operation.

Caution

Safety Instruction

Safety Instructions for wiring process

Prior to wiring works, make sure that every power is turned off. If not, electric shock or

damage on the product may be caused.

After wiring process is done, make sure that terminal covers are installed properly before

its use.Fail to install the cover may cause electric shocks.

Warning

Check rated voltages and terminal arrangements in each product prior to its wiring

process.Applying incorrect voltages other than rated voltages and misarrangement among

terminals may cause fire or malfunctions.

Secure terminal screws tightly applying with specified torque.If the screws get loose, short

circuit, fire or abnormal operation may be caused.

Securing screws too tightly will cause

damages to the module or malfunctions, short circuit, and dropping.

Be sure to earth to the ground using Class 3 wires for FG terminals which is exclusively

used for PLC. If the terminals not grounded correctly, abnormal operation or electric shock

may be caused.

Don’t let any foreign materials such as wiring waste inside the module while wiring,

which may cause fire, damage on the product or abnormal operation.

Make sure that pressed terminals get tighten following the specified torque. External

connector type shall be pressed or soldered using proper equipments.

Caution

Safety Instruction

Safety Instructions for test-operation and maintenance

Don’t touch the terminal when powered. Electric shock or abnormal operation may occur.

Prior to cleaning or tightening the terminal screws, let all the external power off including

PLC power. If not, electric shock or abnormal operation may occur.

Don’t let the battery recharged, disassembled, heated, short or soldered. Heat, explosion

or ignition may cause injuries or fire.

Warning

Do not make modifications or disassemble each module.Fire, electric shock or abnormal

operation may occur.

Prior to installing or disassembling the module, let all the external power off including

PLC power. If not, electric shock or abnormal operation may occur.

Keep any wireless equipment such as walkie-talkie or cell phones at least 30cm away

from PLC. If not, abnormal operation may be caused.

When making a modification on programs or using run to modify functions under PLC

operations, read and comprehend all contents in the manual fully. Mismanagement will

cause damages to products and accidents.

Avoid any physical impact to the battery and prevent it from dropping as well. Damages

to battery may cause leakage from its fluid. When battery was dropped orexposed under strong

impact, never reuse the batte

ry again. Moreover skilled workers are needed when exchanging

batteries.

Caution

Safety Instruction

Safety Instructions for waste disposal

Product or battery waste shall be processed as industrial waste. The waste may discharge

toxic materials or explode itself.

Caution

Revision History

Version Date Contents Revised position

V 1.0 ’10.11 First edition -

V 2.0 ’17. 4 Add service setting by tag

XG5000 V4.0 UI updated

CH6

Entire

※The number of User’s manual is indicated right part of the back cover.

About User’s Manual

Congratulations on purchasing PLC of LSIS Co., Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions,

performances, installation and programming of the product you purchased in order for correct use and

importantly, let the end user and maintenance administrator to be provided with the User’s Manual.

The User’s Manual describes the product. If necessary, you may refer to the following description and order

accordingly. In addition, you may connect our website (http://www.lsis.com/) and download the information

as a PDF file.

Relevant User’s Manuals

Title Description No. of User’s

Manual

XG5000 User’s

Manual

It describes how to use XG5000 software especially about online

functions such as programming, printing, monitoring and

debugging by using XGT series products.

10310000512

XGK/XGB Series

Instruction &

Programming

It describes how to use the instructions for programming using

XGK/XGB series. 10310000510

XGB Hardware

User’s Manual

It describes how to use the specification of power/input

/output/expansion modules, system configuration and built-in

High-speed counter for XGB basic unit.

10310000926

XGB Analog

User’s Manual

It describes how to use the specification of analog input/analog

output/temperature input module, system configuration and built-

in PID control for XGB basic unit.

10310000920

XGB Position

User’s Manual

It describes how to use built-in positioning function for XGB unit. 10310000927

XGB Cnet I/F

User’s Manual

It describes how to use built-in communication function for XGB

basic unit and external Cnet I/F module.

10310000816

XGB Fast Ethernet

I/F User’s Manual

It describes how to use XGB FEnet I/F module.

10310000873

About User’s Manual

Current XBL-EIPT manual is written based on the following version.

Related OS version list

Product name OS version

XGB-XBCH

V2.80

XGB-XBCS

V1.90

XGB-XBCU

V1.70

XGB-XBMH V1.10

XGB-XBMS V3.80

XGB-XECH

V2.20

XGB-XECS

V1.80

XGB-XECU V1.70

XG5000 V4.21

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LSIS Unità di controllo

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGB Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS Starvert iG5A Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS SV-iS7 series Manuale utente

LSIS

LSIS CENT-S100 Manuale utente

LSIS

LSIS S100 Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS S100 Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente