Luceo Technologies X-BERT Series Manuale utente

USER MANUAL

HIGH SPEED CLOCK SOURCE

P/N L-6001-CLK20-1

P/N L-6001-CLK20-2

SERIES: X-BERT/PARALLEX SYSTEM

DOC.REV.1.6

HIGH SPEED Clock Source User Manual

I.) Index

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

GENERAL 3

SAFETY INFORMATION 3

CLASSIFICATION 3

SAFETY INSTRUCTIONS 3

BEFORE INITIALIZING AND OPERATING THE UNIT 3

OPERATING THE UNIT 4

SAFETY SYMBOLS 5

GENERAL DESCRIPTION 6

KEY FEATURES OF THE CLOCK SOURCE MODULE 8

INSTALLATION 9

BEFORE INITIALIZING AND OPERATING THE UNIT 9

INITIAL INSPECTION 9

OPERATING ENVIRONMENT 9

TEMPERATURE 9

HUMIDITY 9

VENTILATION 9

HANDLING CONNECTORS 10

STORING AND SHIPPING 10

CLAIMS AND REPACKAGING 10

RETURNING SHIPMENTS TO LUCEO TECHNOLOGIES GMBH 10

OPERATING INSTRUCTIONS 12

OPERATING KEYS OF CLOCK SOURCE 12

STATUS LED’S OF CLOCK SOURCE MODULE 13

GETTING STARTED 13

GUI AND PROGRAMMING REFERENCE 13

ABOUT LUCEO 14

APPENDIX 15

FIGURES 15

TABLES 16

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

GENERAL

SAFETY INFORMATION

CLASSIFICATION

The clock source module has of a metal chassis that is directly connected to earth when plugged into

the PARALLEX® chassis.

SAFETY INSTRUCTIONS

The following safety instructions must be observed whenever the unit is operated, serviced, or

repaired. Failure to comply with any of these instructions or with any precaution or warning contained

in the user’s manual is in direct violation of the standards of design, manufacture, and intended use of

the unit. Luceo Technologies GmbH assumes no liability for the customer’s failure to comply with any

of these safety requirements.

BEFORE INITIALIZING AND OPERATING THE UNIT

Inspect the unit for any signs of damage, and read the user’s manual thoroughly.

Install the unit as specified in the Getting Started section.

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

OPERATING THE UNIT

Warning

To avoid the risk of injury or death, always observe the following precautions before initializing the

unit:

Use the Module ONLY in the X-BERT or PARALLEX ® mainframe.

Willfully interrupting the protective earth connection is prohibited.

Never look into the end of an optical cable connected to an optical output device that is

operating. Laser radiation is invisible, and direct exposure can severely injure the human eye.

Turning off the power to the device does not always block the externally supplied radiation to

the connector at the input of the unit.

Do not use the unit outdoors.

To prevent potential fire or shock hazard, do not expose the unit to any source of excessive

moisture.

Do not operate the unit when its covers or panels have been removed.

Do not interrupt the protective earth grounding. Any such action can lead to a potential shock

hazard that can result in serious personal injury.

Do not operate the unit if an interruption to the protective grounding is suspected. In this case,

ensure that the unit remains inoperative.

Do not attempt to adjust or perform any maintenance or repair procedure when the unit is

opened and connected to a power source.

Repairs are to be carried out only by a qualified professional.

Do not attempt any adjustment, maintenance, or repair procedure to the unit’s internal

mechanism if immediate first aid is not accessible.

Disconnect the power cord from the unit before adding or removing any components.

Operating the unit in the presence of flammable gases or fumes is extremely hazardous.

Do not perform any operating or maintenance procedure that is not described in the user’s

manual.

Some of the unit’s capacitors can be charged even when the unit is not connected to the

power source.

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

SAFETY SYMBOLS

The following symbols and messages can be marked on the unit (Table 1). Observe all safety

instructions that are associated with a symbol.

Table 1: Safety Symbols

Symbol

Description

Laser safety. See the user’s manual for instructions on handling and operating the unit

safely.

See the user’s manual for instructions on handling and operating the unit safely.

Electrostatic discharge (ESD). See the user’s manual for instructions on handling and

operating the unit safely.

Frame or chassis terminal for electrical grounding within the unit.

Protective conductor terminal for electrical grounding to the earth.

WARNING

The procedure can result in serious injury or loss of life if not carried out in proper

compliance with all safety instructions. Ensure that all conditions necessary for safe

handling and operation are met before proceeding.

CAUTION

The procedure can result in serious damage to or destruction of the unit if not carried

out in compliance with all instructions for proper use. Ensure that all conditions

necessary for safe handling and operation are met before proceeding.

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

GENERAL DESCRIPTION

The clock source high speed module is build for use in the PARALLEX(R) mainframe, which has a

modular setup depending on the user’s configuration (E-BERT-, O-BERT-, Clock Source-, Clock

divider-, CDR-module). The mainframe is controlled via GPIB.

The clock source module is the ideal module to provide clock signals with good jitter and noise

performance up to 17GHz. It can be driven by an external reference clock between 78.125MHz and

1.25GHz.

The clock output signal is single ended. Optional available is a trigger output.

Furthermore the clock source settings are controllable by the PARALLEX® graphical user interfaces

(X-BERT PARALLEX GUI) via a GPIB interface. The GPIB commands for controlling the clock source

module are documented in the GPIB programmer’s guide.

Please take a look at our website www.luceotec.com for newly released modules; we are constantly

expanding our product spectrum.

Figure 1: Typical appearance of the PARALLEX®

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

Figure 2: Collection of PARALLEX® modules

HIGH SPEED Clock Source User Manual

II.) General

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

KEY FEATURES OF THE CLOCK SOURCE MODULE

Variable output frequency from (78.125) | 312.5MHz to 20GHz

Variable output power

Switch for internal or external reference select

Variable trigger clock output

Controllable via GPIB commands

Differential clock output

Small size: 1” width

Standard Accessories

Dust plugs for ports

User’s manual

Programmer’s guide for GPIB

______________________

HIGH SPEED Clock Source User Manual

III.) Installation

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

INSTALLATION

BEFORE INITIALIZING AND OPERATING THE UNIT

Inspect the unit for any signs of damage.

Read the user’s manual thoroughly, and become familiar with all safety symbols and

instructions to ensure that the unit is operated and maintained safely.

INITIAL INSPECTION

Check that the unit and contents are complete:

Wear an anti-static wrist strap, and work in an electrostatic discharge (ESD) controlled area.

Inspect the shipping container for any indication of excessive shock to the contents, and

inspect the contents to ensure that the shipment is complete.

Inspect the unit for structural damage that can have occurred during shipping.

Keep the packaging.

Immediately inform Luceo Technologies GmbH and, if necessary, the carrier if the contents

of the shipment is incomplete, if the unit or any of its components are damaged or defective,

or if the unit does not pass the initial inspection.

OPERATING ENVIRONMENT

In order for the unit to meet the specifications, the operating environment must meet the following

conditions for temperature, humidity and ventilation.

TEMPERATURE

The unit can be operated in the temperature range of 0 to 50 °C.

HUMIDITY

The unit can be operated in environments with up to 85% humidity (10 to 50 °C). Do not expose it to

any environmental conditions or changes to environmental conditions that can cause condensation to

form inside the unit.

VENTILATION

The unit contains holes to achieve airflow to transport the heat out of the module. Do not place any

stickers or labels on the module cover which will reduce the airflow. Blocking the air circulation of the

unit can cause the unit to overheat, compromising its reliability and possibly leading to permanent

damage.

Warning To avoid electrical shock, do not initialize or operate the unit if it shows

any sign of damage to any portion of its exterior surface, such as the outer cover

or panels.

HIGH SPEED Clock Source User Manual

III.) Installation

www.luceotec.com

Clock Source High Speed User Manual --- Rev 1.6 --- 2013/02

Warning

Do not use the unit outdoors.

To prevent potential fire or shock hazard, do not expose the unit to any

source of excessive moisture.

HANDLING CONNECTORS

Caution

Connecting damaged or dirty cables, optical fibers or connectors to the unit

can damage the connectors of the unit.

Use a torque wrench with a maximum torque of 1Nm

(0.74 lbs-ft) to connect cables to the SMA connectors.

A torque of more than 1Nm can damage the SMA connectors permanently.

Use of inappropriate tools when connecting cables and fibers to connectors

(wrenches, spanners etc) can result in mechanical damage to adjacent

connectors and to the connector itself. Similar damage can occur if using a

torque wrench set to a torque above the maximum recommended value.

It is recommended to use dust caps or 50Ω terminations for unused ports /

connectors to avoid connectors becoming damaged by dirt or electrostatic

discharge.

Ensure that long cables or other connected equipment cannot apply forces

or torques that may damage the connectors.

Do not stand the unit on the connectors, as it may damage them.

Optical connectors must be kept clean to avoid damage or performance

degradation. All optical connectors have removable adapters to allow access

to the cleanable surface.

Please ensure adequate cleaning procedures. Ask Luceo Technologies for

advice if required.

STORING AND SHIPPING

To maintain optimum operating reliability, do not store the unit in locations where the temperature falls

below -40 °C or rises above 70 °C. Avoid any environmental condition that can result in internal

condensation. Ensure that these temperature and humidity requirements can also be met whenever

the unit is shipped.

CLAIMS AND REPACKAGING

Immediately inform Luceo Technologies GmbH and, if necessary, the carrier, if

The content of the shipment is incomplete

The unit or any of its components are damaged or defective

The unit does not pass the initial inspection

In the event of carrier responsibility, Luceo Technologies GmbH will allow for the repair or replacement

of the unit while a claim against the carrier is being processed.

RETURNING SHIPMENTS TO LUCEO TECHNOLOGIES GMBH

Luceo Technologies GmbH only accepts returns for which an approved Return Material Authorization

(RMA) has been issued by Luceo Technologies GmbH sales personnel. This number must be

obtained prior to shipping any material to Luceo Technologies GmbH. The owner’s name and address,

the model number and full serial number of the unit, the RMA number, and an itemized statement of

claimed defects must be included with the return material.

Questo manuale è adatto per i seguenti modelli

Altri manuali Luceo Technologies Unità di controllo

Luceo Technologies

Luceo Technologies PARALLEX Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente