M-system R3-PA16 Manuale utente
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 1 / 6
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Totalized pulse input module .............................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■HOT SWAPPABLE MODULES
• Replacing the module does not affect other modules on
the same base. Thus, the module can be replaced while
the power is ON. However, replacing multiple modules
at once may greatly change live voltage levels. We highly
recommend to replace them one by one.
■GENERAL PRECAUTIONS
• DO NOT set the switches on the module while the power
is supplied. The switches are used only for maintenance
without the power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).
TOTALIZED PULSE INPUT MODULE
(Pi 16 points) MODEL R3-PA16
R3-PA16
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 2 / 6
COMPONENT IDENTIFICATION
RUN LED
1
11
12
13
14
15
16
17
18
19
20
2
3
4
5
6
7
8
9
10
ERR LED
Status Indicator LED
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
■ FRONT VIEW ■ SIDE VIEW
SW3
ON
4
3
2
1Count Reset
Count Reset Input
Set the Count Reset SW to OFF to start counting.
Functions
Count Setting
from Host PC/PLC
■STATUS INDICATOR LED
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with excitation abnormality;
Green in normal operating conditions.
Input status indicator: Red LED; turns on with the input
ON.
■SIDE DIP SW
(*)Factory setting
• Count Reset: SW3-1
SW COUNT RESET
NORMAL COUNT RESET
SW3-1 OFF (*) ON
Note: Be sure to turn OFF during use.
• Count Reset Input: SW3-3
SW COUNT RESET INPUT
INVALID VALID
SW3-3 OFF (*) ON
• Count Setting from Host PC/PLC: SW3-4
SW COUNT SETTING FROM HOST PC/PLC
COUNT RESET COUNT PRESET
SW3-4 OFF (*) ON
(For option /PRS, count preset is ON)
Note : Be sure to set unused SW3-2 to OFF.
PC CONFIGURATOR
With configurator software, settings shown below are available.
Refer to the software manual of R3CON for detailed operation.
• Max. Pulse count: 1 to 65,535 (factory setting: 10,000)
• Totalized count value (V2.01 or higher)
• Accumulated pulse count (Pulse counts are changeable by using the PC Configurator, refer to “Counter setting from host
PC/ PLC” section hereafter.)
R3-PA16
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 3 / 6
FUNCTIONS
■MANUAL COUNT RESET
1) Remove Network Module or its cables and interrupt com-
munication with other devices.
2) Turn ON the Count Reset SW.
3) Return the module to the base and turn the power supply
on.
4) ERR LED turns on and the module starts resetting its
counter. When the resetting is complete, the LED turns
to green. DO NOT remove the power while the red LED
is on. The RUN LED starts blinking at the same time.
5) After the green LED is confirmed, turn the power supply
off.
6) Turn OFF the Count Reset SW.
7) Return the Network module onto the base and turn the
power supply on.
Note: Count Reset SW must be turned OFF after this proce-
dure because the module does not start counting with
ON state.
■REMOTE COUNT RESET INPUT
With the Count Reset Input SW (SW3-3) turned ON, the
Pi 16 pulse input can be used to remotely reset the count
values.
SW3-3 = OFF: Pi 16 is used as a pulse input.
SW3-3 = ON: Pi 16 is used to reset the count values for the
Pi 1 through Pi 15. One pulse supplied at the Pi 16 will be
recognized as a reset signal.
■REMOTE COUNT RESET OPERATION
1) ERR LED turns on (red color) when the reset signal is
received.
2) In 1 second, the module starts resetting its counter.
When the resetting is complete, the LED turns to green.
3) After 1 second, ERR LED turns back to the state before
the reset signal has been received.
Note: Reset signals received while the module is processing (1)
through (3) are ignored.
■COUNT RESET FROM HOST PC/PLC
Refer to “COUNTER SETTING FROM HOST PC/PLC” sec-
tion hereafter.
R3-PA16
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 4 / 6
COUNTER SETTING FROM HOST PC/PLC
■COUNTER RESET
(Available for R3-NC1, R3-NC3, R3-NE1, R3-NM1, R3-NDx, R3-NFL1, R3-NP1, R3-NML3 (Firmware version 2.00 or later))
Setting SW3-4 OFF and turning power on enable the function.
The bits indicating the channels to reset counter are allocated in the first word from host PC/PLC.
When these bits are changed from 0 to 1, the counter is reset. When it is confirmed that the counter is reset, return to 0.
Notice that if the bit remains at 1, the next reset will not work.
0
15
Count reset CH.1
Count reset CH.16
Count reset CH.2
Count reset CH.3
Count reset CH.4
■COUNTER PRESET
(Available in combination with R3-NE1, R3-NM1 (Firmware version 2.00 or later), and R3-PA16 displayed ‘SW3-4 RESET/
PRESET’ on the right side)
Setting SW3-4 ON and turning power on enable the function.
Write the preset value to the Holding Resisters, which has same address as the Input Resisters.
• Input Resisters • Holding Resisters
Address
n+0
n+1
n+2
n+3
n+14
n+15
Input 1
Input 3
Input 15
Input 2
Input 4
Input 16
Address
n+0
n+1
n+2
n+3
n+14
n+15
Preset value of Input 1
Preset value of Input 3
Preset value of Input 15
Preset value of Input 2
Preset value of Input 4
Preset value of Input 16
R3-PA16
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 5 / 6
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
1
11
12
13
14
15
16
17
18
19
20
2
3
4
5
6
7
8
9
10
130 (5.12)
27.5 (1.08) 109 (4.29)
POSITIONING
GUIDE
TERMINAL
COVER
20–M3
SCREW
6.2
(.24)
■CONNECTION DIAGRAM
1INTERNAL
BUS A
INTERNAL
BUS B*
BUS CONNECTOR
11
18
9
19
10
20
17
16
15
14
13
12
11
8
7
6
5
4
3
2
INTERNAL
POWER
Pi 1
Pi 16
Pi 15
Pi 14
Pi 13
Pi 12
Pi 11
Pi 10
Pi 9
Pi 8
Pi 7
Pi 6
Pi 5
Pi 4
Pi 3
Pi 2
COM(+)
0V
+24V
■R3-PA16x/A
1
18
9
19
Pi 1
Pi 16
10
20
17
Pi 15
16
Pi 14
15
Pi 13
14
Pi 12
13
Pi 11
12
Pi 10
11
Pi 9
8
Pi 8
7
Pi 7
6
Pi 6
5
Pi 5
4
Pi 4
3
Pi 3
2
Pi 2
0V
■R3-PA16x
**
*For dual redundant communication.
**DO NOT use the terminals No. 9 and 19.
R3-PA16
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-8389 Rev.7 P. 6 / 6
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.5 N·m
■SOLDERLESS TERMINAL
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit.
Applicable wire size: 0.3 – 0.5 mm2
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd., Nichifu Co., Ltd.
12max
6max
3max 4min
3.2 dia.
(mm)
Indice
Altri manuali M-system Unità di controllo
M-system
M-system R3-SV8B Manuale utente
M-system
M-system R7M-MS4 Manuale utente
M-system
M-system R7HL-DC16B-R Manuale utente
M-system
M-system M8CD1 Manuale utente
M-system
M-system R5-PA2 Manuale utente
M-system
M-system R7C-EC16B/UL Manuale utente
M-system
M-system 73VR3100 Manuale utente
M-system
M-system R7HL-DC8C Manuale utente
M-system
M-system R7M-DAC16D Manuale utente
M-system
M-system R8-DCM16ALK Manuale utente
M-system
M-system R30US2 Manuale utente
M-system
M-system R6D-TS2 Manuale utente
M-system
M-system R7HL-DAC15E Manuale utente
M-system
M-system R7M-EC16A Manuale utente
M-system
M-system R7D-EA16 Manuale utente
M-system
M-system R3-NL1 Manuale utente
M-system
M-system R7E-EA8 Manuale utente
M-system
M-system R30YV4 Manuale utente
M-system
M-system R7L-EC16A Manuale utente
M-system
M-system R7ML-YV2 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
