M-system R3-TS4 Manuale utente

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8362 Rev.5 P. 1 / 4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Thermocouple input module (body + 4 CJC sensors)........(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

THERMOCOUPLE INPUT MODULE

(4 points, isolated) MODEL R3-TS4

R3-TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8362 Rev.5 P. 2 / 4

COMPONENT IDENTIFICATION

SW1SW2

SW3

■FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Conv.

Rate

Temp.

Unit

Input 2 (SW1)

Input 4 (SW2)

T/C

Input 1 (SW1)

Input 3 (SW2)

Burnout

Functions

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with burnout;

Green in normal operating conditions.

■SIDE DIP SW

(*) Factory setting

• Thermocouple Type: SW1, SW2

INPUT 1 (SW1) INPUT 2 (SW1)

T/CINPUT 3 (SW2) INPUT 4 (SW2)

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

K (CA) (*)

OFF OFF OFF

E (CRC)

OFF

OFF OFF OFF

OFF OFF

J (IC)

ON ON

OFF OFF

ON ON

OFF OFF

T (CC)

OFF OFF

OFF OFF OFF

OFF

B (RH)

OFF

ON ON

OFF OFF

ON ON

OFF

ON ON ON

OFF

ON ON ON

OFF

C (WRe 5-26)

OFF OFF OFF

ON N

OFF OFF

ON ON

OFF OFF

ON U

OFF

ON L

ON ON

OFF

ON ON ON

OFF

ON P (Platinel II)

OFF OFF

ON ON

OFF OFF

ON ON (PR)

• Burnout: SW3-1

SW3-1 BURNOUT

OFF Upscale (*)

ON Downscale

• Temperature Unit: SW3-2, 3-3

SW3-2 SW3-3 TEMP. UNIT

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

• Conversion Rate: SW3-4

SW3-4 CONV. RATE

OFF 250 msec. (*)

ON 1 sec.

R3-TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8362 Rev.5 P. 3 / 4

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Zero Adjust -320.00 to +320.00 0.00

Full Adjust -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

Unused 0: Enable

1: Disable

0: Enable

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit (V0.10 or higher) No check mark: Limits to the scaling values equivalent

to -15 % to +115 %.

Check-marked: Limits within Zero Scale to Full Scale.

No check mark

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

R3-TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8362 Rev.5 P. 4 / 4

■CONNECTION DIAGRAM

*For dual redundant communication.

–

T/C

comp. wire

–

INPUT 1

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 2

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 3

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 4

CJC

SENSOR

BUS CONNECTOR

INTERNAL POWER

INTERNAL BUS A

INTERNAL BUS B*

• Unused Input Channels

(Choose K (CA) thermocouple for unused channels.)

Unused channels left open are equal to the burnout, which

turns the red ERR LED on and sets a burnout ag at the

PLC or the host device.

Unused channels can be specied and set so on the

Congurator Software (model: R3CON) without needing to

short at the eld terminals.

INPUT 1

INPUT 2

INPUT 3

INPUT 4

12 14 17 19

CJC

SENSOR

Short

Close across the unused input terminals as shown below.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.75 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

12max

6max

3max 4min

3.2 dia.

(mm)

Altri manuali M-system Sistema I/O

M-system

M-system R7F4DC-DAC16C-H Manuale utente

M-system

M-system R7D-YS2A Manuale utente

M-system

M-system R3-SS8 Manuale utente

M-system

M-system R7ML-SV4 Manuale utente

M-system

M-system R3-DC64A Manuale utente

M-system

M-system R7F4DC-DA16A-C Manuale utente

M-system

M-system EtherCAT R7I4DECT-1-YVF4 Manuale utente

M-system

M-system R3-SS8N Manuale utente

M-system

M-system R7E-EC16B Manuale utente

M-system

M-system 60C Manuale utente

M-system

M-system R7M-DA16-R Manuale utente

M-system

M-system R3-AS8 Manuale utente

M-system

M-system R7L-TS4 Manuale utente

M-system

M-system R7L-TS4-R Manuale utente

M-system

M-system R7D-YV2/UL Manuale utente

M-system

M-system Remote I/O R8 Series Manuale utente

M-system

M-system R7D-SV4/UL Manuale utente

M-system

M-system R3-SV8N Manuale utente

M-system

M-system R8-SS4N Manuale utente

M-system

M-system R7L-DC16A Manuale utente

M-system

M-system R3S-RS4A Manuale utente

M-system

M-system R3S-YV4 Manuale utente

M-system

M-system R7E-EC8A Manuale utente

M-system

M-system R7 Series Manuale utente

Manuali Sistema I/O popolari di altre marche

WAGO

WAGO 750-344 Manuale utente

Teknim

Teknim TWM-1887 Manuale di istruzioni

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuale utente

BERGHOF

BERGHOF ECC DIO 16/16 Manuale di istruzioni

Advantech

Advantech PCM-27J3AU Manuale di installazione e funzionamento

Festo

Festo CP-E08-M12-CL Manuale utente

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuale utente

Hitachi

Hitachi HX-RIO3 Series Manuale utente

NUUO

NUUO SCB-A08 Manuale utente

jablotron

jablotron JB-110N Manuale utente

Omron

Omron SYSMAC C200H Manuale utente

DOLD

DOLD SAFEMASTER M Manuale utente

ABB

ABB OPT-MF-001 Manuale utente

Omron

Omron SYSMAC C2000H Manuale utente

Helmholz

Helmholz TB20 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD2 Manuale utente

Automationdirect.com

Automationdirect.com DL305 Manuale utente

WAGO

WAGO I/O-SYSTEM 750 Manuale utente