M2 Antenna Systems 222XP40 Manuale utente

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................222XP40

Frequency Range.......................222 To 223.5 MHz

*Gain, V & H ..............................16.8 dBd (18.9 dBi)

Front to back ..............................20 dB Typical

Beamwidth ...............................E = 19° H = 21°

Feed type ...................................Folded Dipole

Feed Impedance........................50 Ohms Unbalanced

VSWR.........................................1.2:1 Typical

Input Connector..........................“N” Female

Power Handling..........................1.5 kW

Boom Length / Dia......................35’ / 1-1/2”,1-1/4”,1”,3/4”

Maximum Element Length..........26-5/8”

Turning Radius:..........................240” (20’)

Stacking Distance.......................132” to 144”

Mounting.....................................H or V

Mast Size....................................2” Nom.

Wind area / Survival...................3.0 Sq. Ft. / 100MPH

Weight / Ship Wt.........................15 Lbs. / 18 Lbs.

M2 Antenna Systems, Inc.

Model No: 222XP40

FEATURES:

The 222XP40 is the hot, new dual polarized Yagi specifically for EME and long haul terrestrial communica-

tions. It is our latest design using computer techniques to allow maximum gain and patterns in both the horizontal

and vertical planes. The vertical elements have been shifted /4 in front of the horizontal set to allow circular

polarization if needed. This means four possible polarization modes with one antenna! Two antennas stacked are a

great tropo and EME package and four or more are amazing allowing Even small Yagi EME contacts using CW or

JT65B. Structurally the 222XP40 is sturdy and clean. Elements are 3/16” 6061-T6 aluminum rod mounted through

the boom on UV stabilized “button” insulators. The boom is a full 1-1/2 inch diameter in the middle 3 sections

tapering through two 1-1/4 inch sections to stiff 1” and a short 3/4 inch front tip. The main ‘N’ connectors are O-ring

sealed to the CNC machined block and 4:1 balun connectors feature triple seals. The internal module connections

are sealed in a space-age silicone gel. See our other accessories including preamps, power dividers and custom

made phasing lines.

SPECIFICATIONS:

XP = cross polarized; H = horizontal; V = vertical; EME = Earth-Moon-Earth; *Subtract 2.14 from dBi for dBd

TOOL REQUIRED FOR ASSEMBLY: screwdriver, 11/32 nut driver or wrench, 7/16” and 1/2” socket or end

wrenches, measuring tape.

1. Start by laying out the boom sections using the DIMENSION sheet as a guide. Use the appropriate

8-32 screws and locknuts as shown to join the sections. To make the assembly easier, support

the completed boom about waist high on bucks, tables, etc. Or even better, drive a 1-1/2” to 2”

pipe into the ground and temporarily attach boom using the boom to mast plate and U-bolts at the

balance point shown on the DIMENSION SHEET.

2. Lay out the 3/16” elements by length and position as shown the DIMENSION sheet. Start with the

REFLECTOR (26.188”) element. Balance across finger to find center and push on a black button

insulator to about 1/2” from center. Push the element through the holes 1/2" from the rear of the

boom and install the second button, snugging it up into boom. DO NOT BOTHER WITH

ACCURATELY CENTERING the element at this time and DO NOT INSTALL the stainless steel

internal locking “KEEPERS” yet. This is easier to do after all the elements are installed in the

boom.

3. Install the 3/16” ROD DRIVEN ELEMENT as you did the reflector. Then continue with the

installation of the DIRECTORS. Note that the Director Elements do not consistently diminish in

length from rear to front, so pay close attention to length and position. D3 AND D17 are on

different boom diameter sections so their length is different also.

4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount the element

sticking out on each side of the boom. Once you have all the elements centered, sight down the

element tips from the rear comparing each side. Look for any obvious discrepancies and correct if

found.

5. Begin installing the stainless “keepers.” Use

thumb and index finger to hold a keeper over

end of the 3/8 x 3” push tube (keeper dished

into tube). Hold the element firmly and start

the keeper onto the rod by applying pressure

with the push tube. Push the keeper until up

tight against the button insulator (Locking

pliers, lightly clamped up against opposite

button insulator will help maintain center

reference and keep you from pushing the

first keeper too far). Repeat for the opposite

side. Continue installing keepers until all

elements are locked in place.

6. Now loosen the 1-1/2” U-Bolts on the boom to mast plate and rotate the boom 90 degrees and

repeat steps 2 through 5 for the VERTICAL set of elements.

7. Mount the DRIVEN ELEMENT BLOCK ASSEMBLIES to the boom using 8-32 X 1-1/4" screws.

Orient the block with the ‘N’-connector facing towards the rear of the antenna and balun ‘F’-

connectors facing towards the front.

8. For the two DRIVEN ELEMENT BLOCK ASSEMBLIES, install a gold 3/8” SEAL NUT all the way

onto BOTH ‘F’-connectors, with the black Neoprene seal facing out. Attach the balun to one of the

‘F’-connectors on the block, and connect the other side to the other ‘F’-connector. Now tighten

the connectors gently using a 7/16" end wrench. Once the connectors are tight, back the Seal

Nuts out and finger-tighten firmly up against the face of the connectors (or tighten very gently with

222XP40 ASSEMBLY MANUAL

1/2” end wrench). Secure the balun close to the boom with a nylon cable tie in such a way so that

it’s snug but not crushing or kinking the coax.

9. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the four SHORTING

BARS. Slide the bars onto the 3/16” rod driven element tips and then onto the Driven Element

Block Rods. Position the Shorting Bars as specified on the DIMENSION SHEET: the distance

given is between the outer edge of the Driven Element Block and the inner edge of the Shorting

Bar. Align the bars and rods with each other and tighten the setscrews.

10. If you have not already done so, attach the boom to mast plate to the boom. It is normally

mounted at the balance point, as shown on the DIMENSION SHEET. Use two 1-1/2" U-bolts and

the stainless nuts and lock washers provided. DO NOT OVER TIGHTEN. 2” U-bolts are provided

for mounting the antenna to your NON-CONDUCTIVE mast.

“XP” Yagis require the coax cables exit the boom just at the rear reflector and at right angle to the

rear reflector. When mounting two antennas side by side the rear reflectors must be vertical so the

cables can exit the boom horizontally. M2 offers a ’T’ brace kit for two or more antenna arrays. It

supports the cables from each XP Yagi and routes the cables back to the main crossboom. The two

phasing or feed line represents significant weight it is best to have them, or a temporary equivalent,

attached and hanging from the rear of the boom when positioning the boom to mast plate.

11. OVERHEAD GUY SYSTEM

Locate the 3/8 x 24” fiberglass rod, the three fiberglass rod mast clamp blocks, the fiberglass mast

clamp flag and the remaining four 8-32 x 1-1/4” screws and locknuts. Attach two fiberglass rod

mast clamp blocks to the boom to mast plate with two 8-32 x 1-1/4” screws and locknuts as shown

below in the figure. Insert the 3/8 x 14” fiberglass rod into the slot formed by the two blocks and

tighten the two locknuts. Now assemble the remaining fiberglass rod mast clamp and mast clamp

flag with two 8-32 x 1-1/4” screws and locknuts. Slide the assembly onto the fiberglass rod as

shown below in the figure and tighten the two screws.

222XP40 ASSEMBLY MANUAL

12. Using the Dimension Sheet as a guide, install the two 1/4” eyebolts into the top side of the 1” front

and rear boom sections. Align the eyes with the boom and secure with 1/4-20 locknuts.

13. Install the two turnbuckles into the fiberglass rod mast clamp assembly as shown above in the fig-

ure. Adjust threads until just one or two show inside turnbuckle body. Attach one end of the KEV-

LAR cord to the rear eyebolt by taking two wraps through the “eye” and finishing with two half-

hitches or a square knot. Adjust to leave 2” to 4” of cord after knots. Attach the other end of the

cord to the front eyebolt in the same way. Equalize excess cord at the fiberglass riser and cut. Take

rear cord end and make two wraps through rear turnbuckle eye, then pull line taut until the rear

boom end levels and knot as above. Repeat for front cord and turnbuckle. If you cannot straighten

the boom by adjusting the turnbuckles, open the turnbuckles again as before with no threads show-

ing inside the turnbuckle body. Loosen the KEVLAR knots and pull taut again, perhaps even lifting

the boom ends slightly. Re-tie the knots and final adjust the boom to level with the turnbuckles. Use

solid #12 awg copper wire or equivalent to “safety wire” the turnbuckles to prevent loosening.

NOTE: Kevlar has a core of Arimid fiber with a woven jacket of Dacron for protection from

abrasion. Arimid fiber does not stretch and both materials are UV stabilized for decades of intense

sun with no degredation. They are also impervious to salt spray and acid rain. Only fire will make

KEVLAR fail. Philistran is another type of Arimid fiber guy cord and can be used interchangeably in

this application. (It just costs more).

14. MOUNTING INFORMATION

(M2 offers 2” X 1/4” wall FIBERGLASS TUBE in various lengths and we make a wide range of “H”

frames for both “Xpol” and linear Yagis).

MOUNTING THE 222XP40 ON A METALLIC MAST WILL GREATLY DEGRADE ITS

PERFORMANCE IN THE PLANE OF THE MAST, THEREFORE THE ANTENNA SHOULD BE

MOUNTED ON A NON-CONDUCTIVE SUPPORT EXTENDING FROM THE ANTENNA AT LEAST

36”. MOUNTING THE ANTENNA WITH THE ELEMENTS IN AN “X” CONFIGURATION WITH

REFERENCE TO A METAL MAST, DEGRADES PERFOMANCE LESS, BUT IN BOTH PLANES,

NOT JUST ONE.

REMEMBER ALSO THAT THE FEEDLINES MUST EXIT AT THE REAR OF THE ANTENNA! If you

have not already done so, install your antenna on your non-conductive mast. Supporting the

antenna at the boom-to-mast plate will tension the KEVLAR cord and will allow turnbuckle adjust-

ment for a straight boom. Cut any excess length of cord, leaving just 2” to 4”. To prevent fraying,

melt the ends with a match or torch and tape back to main line. NOTE: You may notice that the

boom tips may drop slightly beyond the eyebolts. This is normal and in no way will affect the

performance of the antenna.

15. STACKING INFORMATION

Optimum stacking for two or more 222XP40 antennas either horizontally or vertically is 144” (12

feet / 3.65m) from boom center to boom center. This yields the maximum theoretical gain, with clean

patterns. Reduced stacking distance of 132” is acceptable. When stacking 4 or more antennas use

the same figure, 144” when stacking high or wide. Be sure all antennas are oriented so the

HORIZONTAL and VERTICAL driven element blocks are on the SAME SIDE of the boom and NOT

MIRROR IMAGE to each other. M2also offers low loss LMR400 phase lines and 2 or 4 port power

dividers, depending upon your system requirements.

If you need any additional information or HELP with your system, PLEASE CALL US!

We also have Hints and tips on our Web Site

THIS COMPLETES THE ANTENNA ASSEMBLY.

222XP40 DIMENSION SHEET

222XP40 PARTS & HARDWARE

DESCRIPTION QTY

BOOM, 3/4 X .049 X 33” ALUM. TUBE.................................1

BOOM, 1.0 X .058 X 57” ALUM. TUBE.................................1

BOOM, 1.0 X .058 X 60” SOE ALUM. TUBE........................1

BOOM, 1-1/4 X .058 X 60” SOE, ALUM. ..............................1

BOOM, 1-1/4 X .058 X 54” SOE, ALUM ...............................1

BOOM, 1-1/2 X .058 X 57” SBE, ALUM................................1

BOOM, 1-1/2 X .058 X 60” SOE, ALUM ...............................2

ELEMENT, 3/16 X SEE DIMENSION SHEET ....................40

/2 BALUN, RG6-U...............................................................2

‘T’ MATCH BLOCK ASSEMBLY...........................................2

BOOM TO MAST PLATE, 3/16 X 4 X 6”...............................1

SHORTING BAR (M2ASB0090)...........................................4

KEVLAR, 1/8” X 30 FT.........................................................1

NYLON TIE, 5” BLACK.........................................................4

ALLEN WRENCH, 5/64”.......................................................1

PUSH TUBE, 3/8” X 3” ALUM...............................................1

ASSEMBLY MANUAL...........................................................1

HARDWARE BAG #1

U-BOLT AND CRADLE, 2” ...................................................2

U-BOLT AND CRADLE, 1-1/2” .............................................2

NUT, 5/16-18 SS...................................................................4

LOCKWASHER, 5/16” SPLIT RING SS................................4

TURNBUCKLE, 1/4” X 3-1/4”....... ........................................2

EYEBOLT, 1/4” X 4”..................... ........................................2

NUT, 1/4-20 SS LOCKING .......... ........................................2

HARDWARE BAG #2

NUT SEAL ............................................................................4

BUTTON INSULATOR, 3/16” BLACK POLY ......................80

KEEPER, 3/16” SS .............................................................80

SCREW, 8-32 X 1-3/4” SS, PHILLIPS..................................8

SCREW, 8-32 X 1-1/2” SS, PHILLIPS..................................4

SCREW, 8-32 X 1-1/4” SS, PHILLIPS..................................8

SET SCREW, 8-32 X 1/4” SS...............................................8

LOCKNUT, 8-32 SS............................................................18

HARDWARE BAG #3 (OPTIONAL)

VERT. SUPPORT ROD, 3/8 x 24” FIBERGLASS ROD........1

CLAMP BLOCK, 1/4 x 1” ALUM............................................3

CLAMP BLOCK FLAG, 1/4 x 1-1/2” ALUM...........................1

Indice

Altri manuali M2 Antenna Systems Antenna

M2 Antenna Systems

M2 Antenna Systems 2MCP22 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 140CP14M Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M3FS Manuale utente

M2 Antenna Systems

M2 Antenna Systems 348CP18 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 902-5 YAGI Manuale utente

M2 Antenna Systems

M2 Antenna Systems 440-18X Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2068-26-2 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 75-5AS Manuale utente

M2 Antenna Systems

M2 Antenna Systems 222-10EZ Manuale utente

M2 Antenna Systems

M2 Antenna Systems 915XBISP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 222 HO LOOP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2MCP8A Manuale utente

M2 Antenna Systems

M2 Antenna Systems 10M4DX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M1L Manuale utente

M2 Antenna Systems

M2 Antenna Systems 7-10-30LP8 UP-KIT Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M4X Manuale utente

M2 Antenna Systems

M2 Antenna Systems 300XP12 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 393CP18 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 432-6WL Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M3C Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M-440XPSS Manuale utente

M2 Antenna Systems

M2 Antenna Systems 30M3-125 Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente