M2 Antenna Systems 295XP6 Manuale utente

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.02

Model .........................................295XP6

Frequency Range.......................292 To 298 MHz

*Gain ..........................................8.0 dBiC

Front to back ..............................22 dB Typical

Beamwidth ...............................E=96°

Feed type ...................................“T” Match

Feed Impedance. .......................50 Ohms Unbalanced

Maximum VSWR........................1.2:1 Typical

Input Connector..........................“N” Female

Power Handling ..........................500 Watts

Boom Length / Dia......................37” / 1”

Maximum Element Length..........20”

Turning Radius: ..........................24”

Stacking Distance.......................Call

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival ...................0.5 Sq. Ft. / 100 MPH

Weight / Ship Wt.........................2 Lbs. / 3 Lbs.

M2 Antenna Systems, Inc.

Model No: 295XP6

FEATURES:

The 295XP6 is a small sized, computer optimized, cross-polarized antenna. Depending on phasing between the vertical

and horizontal element set, horizontal, vertical, right or left hand circular polarity is available. Electro-mechanical features

include machined components and stainless steel hardware. The rod elements are centered in the boom on UV stabilized

insulators and secured with stainless steel shaft retainer. All connectors are threaded and O-ring sealed to the feed block.

The block’s internal cavity and connections are encapsulated in a silicone gel that seals out moisture and provides a

dielectric strength 3.7 times greater than air for improved power handling capability. Balun connectors are triple-sealed to

the coax and nut-sealed at the block.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

295XP6 ASSEMBLY MANUAL

TOOLS REQUIRED FOR ASSEMBLY: 1/2” and 7/16” end wrenches or sockets, pliers, measuring tape.

HORIZONTAL ELEMENT ASSEMBLY

1. Separate the 3/16” ROD elements by length into two identical sets, “H” and “V”. Position the “H” element set along the

boom by length and spacing as shown the DIMENSION sheet. Start with the REFLECTOR (longest) element. Balance it

on your finger to roughly determine it’s center point and push on a black button insulator on one side of the rod to about

1” off of center. Next push the REFLECTOR element through the appropriate holes in the boom and allow to protrude

about 1” on the opposite side. Now install the second button, snugging it up to the boom. DO NOT CENTER the element

at this time and DO NOT INSTALL any of the stainless steel SHAFT RETAINERS yet. It is easier to do it after all the

horizontal elements are installed in the boom.

2. Repeat (1) for the installation of the remaining two HORIZONTAL “H” SET of 3/16” ELEMENTS.

3. Now accurately center the elements using a tape measure. EQUALIZE the amount of rod sticking out on each side of the

boom. Once you have all the elements centered, sight down the element tips from the rear comparing each side. Look for

any obvious discrepancies and correct if found.

4. Begin installing the stainless SHAFT RETAINERS. Use thumb and index finger to hold a retainer over end of the 3/8” x 3”

push tube (keeper dished into tube). Hold the element firmly and start the retainer onto the rod by applying pressure with the

push tube. Push the retainer until up tight against the button insulator (Locking pliers, clamped up against opposite button

insulator will help maintain center reference and keep you from pushing the first retainer too far, or, grab the opposite side of

the element and pull it hard sideways to the boom to preload and increase the friction of the element on the button insulators

while pushing the retainer). Repeat for the opposite side. Continue installing retainers until all elements are locked in place.

5. Mount the HORIZONTAL DRIVEN ELEMENT BLOCK / 1/4” ROD ASSEMBLY to the TOP of the boom as pictured on the

DIMENSION SHEET using a 8-32 x 1-1/4” screw and lockwasher. Orient the block with the two balun connectors facing

towards the FRONT of the antenna and the feed connector towards the REAR.

295XP6 DIMENSION SHEET

295XP6 ASSEMBLY MANUAL

6. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS. Slide the bars on the 1/4”

Driven Element Block Rods and the 3/8” driven element rods. Position the shorting bars to the specified dimension on the

DIMENSION SEET, measured BETWEEN THE OUTER FACE OF THE DRIVEN ELEMENT BLOCK AND THE INNER

FACE OF THE SHORTING BAR. Now tighten the set screws.

VERTICAL ELEMENT ASSEMBLY

1. Repeat steps #1 through #6 for the Vertical elements, using the DIMENSION SHEET as your guide to the lengths and

spacings. Mount the VERTICAL driven element block to the LEFT side of the boom (as viewed from the rear) with the

two balun connectors facing forward (see Dimension Sheet).

COMPLETING ANTENNA ASSEMBLY

1. Before installing the Baluns, thread 3/8” seal nuts fully onto all “F” connectors on both the horizontal and vertical driven

element blocks, with the black Neoprene face of the nuts facing out. Attach Baluns to the Blocks as shown on the figure

on the last page. Tighten the connectors gently using a 7/16” end wrench. Once the connectors are tight, back the seal

nuts out and finger-tighten firmly up against the face of the connectors (or tighten gently with 1/2” end wrench). A lot of

torque is unnecessary. Form baluns close to the boom and secure with a nylon cable tie. Also secure feed coax with

cable ties. Ties should be snug but not crushing or kinking the coax.

2. Attach the 3 x 4 x .125” BOOM TO MAST PLATE about 1” from the rear of the antenna with two 1” U-Bolts. On the

opposite side of the plate loosely install the two sets of 2” cradles with 5/16-18 x 3” bolts, lock washer and locknuts.

3. Attach feedlines and fasten to the boom with cable ties. To provide stress relief use a nylon tie to secure feed coax near

connector on each block. Route feedlines to rear of boom and secure again.

THIS COMPLETES THE ANTENNA ASSEMBLY

Carefully manufactured by:

M2 Antenna Systems, Inc.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 Fax (559) 432-3059

www.m2inc.com email: [email protected]

295XP6 PARTS & HARDWARE

DESCRIPTION .............................................................................. QTY

BOOM SECTION, 1” X .058 X 37”................................................. 1

SLEEVE, 7/8” X .058 X 14”............................................................ 1

ELEMENTS, 3/16” ROD x DIM SHEET......................................... 6

DRIVEN ELEMENT ASSEMBLY................................................... 2

BALUN, RG-6 1/22

PHASE LINE, RG-6 1/4 2

JUNCTION BLOCK ASSEMBLY ................................................... 1

BOOM-TO-MAST PLATE, 3 X 4 X .125"....................................... 1

SHORTING BAR, VHF, 1/4” X 3/4” ............................................... 4

U-BOLT & CRADLE, 2” ................................................................. 2

U-BOLT, 1”..................................................................................... 2

ASSEMBLY MANUAL ................................................................... 1

HARDWARE:

BUTTON INSULATOR................................................................... 12

SHAFT RETAINER, SS ................................................................. 12

NUT, 5/16-18 SS............................................................................ 4

LOCKWASHER, 5/16 SS .............................................................. 4

NUT, 1/4-20 SS.............................................................................. 4

LOCKWASHERS, 1/4 SS .............................................................. 4

SCREW, 8-32 X 1-1/4 SS.............................................................. 2

LOCKNUT, 8-32 SS....................................................................... 2

SETSCREW, 8-32 X 1/4, SS ......................................................... 8

CABLE TIE, NYLON ...................................................................... 6

SEAL NUTS, 3/8-32....................................................................... 4

ALLEN HEAD WRENCH, 5/64” ..................................................... 1

PUSH TUBE, 3/8 X 3”.................................................................... 1

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: (559) 432-3059

www.m2inc.com Email: [email protected]

03/05/09

Rev.00

Indice

Altri manuali M2 Antenna Systems Antenna

M2 Antenna Systems

M2 Antenna Systems FD35.5 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 80M1L Manuale utente

M2 Antenna Systems

M2 Antenna Systems EB-144/RK2M Manuale utente

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 432-6WL Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M18 series Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2068-26-2 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 432-12EME Manuale utente

M2 Antenna Systems

M2 Antenna Systems 436CP16 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 146CP8 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 167XP22 Manuale utente

M2 Antenna Systems

M2 Antenna Systems SYSTEM SAMPLE 3 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 10M7DX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 30M3-125 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M5-440XP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 222XP40 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 436CP42UG Manuale utente

M2 Antenna Systems

M2 Antenna Systems FGSD-3.7DH Manuale utente

M2 Antenna Systems

M2 Antenna Systems 20M4DX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 6M HO LOOP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M4X Manuale utente

M2 Antenna Systems

M2 Antenna Systems 17M5DX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M4LLDD Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente