M2 Antenna Systems 440-11X Manuale utente
M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722
Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com
©2021 M2 Antenna Systems Incoporated 3/01/22
REV B
Model .........................................440-11X
Frequency Range.......................420 To 450 MHz
*Gain ..........................................13.44 dBi
Front to back ..............................20 dB Typical
Beamwidth ...............................E=34° H=43°
Feed type ...................................Folded Dipole
Feed Impedance. .......................50 Ohms Unbalanced
Maximum VSWR........................1.5:1 Typical
Input Connector..........................“N” Female
Power Handling ..........................1 kW
Boom Length / Dia......................60” / 1”
Maximum Element Length..........13-3/4”
Turning Radius: ..........................55”
Stacking Distance.......................34” High & 36” Wide
Mast Size....................................2” Nom.
Wind area / Survival ...................0.6 Sq. Ft. / 100 MPH
Weight / Ship Wt.........................4 Lbs. / 6 Lbs.
M2 Antenna Systems, Inc.
Model No: 440-11X
SPECIFICATIONS:
*Subtract 2.14 from dBi for dBd
FEATURES:
M2 is always trying to design and build new antennas to fit the needs of amateur radio operators. The “X” series of antennas are all designed
to keep the packaging under 48” long to minimize oversize surcharges applied by shippers. The “X” series antennas offer the same performance as its
predecessor, but with shorter boom sections. The boom sections also have a thicker wall for added strength. A side benefit of the “X” series antennas
are that they are more portable with the smaller sections.
The 440-11X replaces our very popular 420-50-11. The 440-11X is a computer optimized broadband yagi featuring an excellent pattern and
good gain across its bandwidth. It can be mounted vertically or horizontally and is ideal for stacking two or more for additional gain. Its light weight yet
sturdy construction keep the cost low and the performance high. Use it for ATV, OSCAR, FM, LONG HAUL TROPO, ETC. We guarantee you will be
impressed.
The heart of the 440-11X is a unique Driven Element Module with superior weather resistance and power handling abilities. All connectors are
O-ring sealed to the CNC machined block and internal connections are sealed in a space-age silicone gel with a dielectric strength nearly 4 times
greater than air. The Balun coax connectors are triple O-ring sealed. Other key mechanical and electrical parts are CNC machined from 6061-T6 alumi-
num and all hardware except U-bolts is stainless steel.
The 440-11X offers you uncompromising performance, enduring mechanical construction, and long term electrical integrity.
Tools handy for assembly process: screwdriver, 11/32” spin-tite or socket, 7/16” and 1/2” end
wrenches / sockets, measuring tape.
1. This antenna uses a one-piece boom.
2. Lay out the elements by length and position as shown the DIMENSION sheet. Start with the
reflector (longest) element and push on a black button insulator to about 1/2” from center. Push the
element through the holes 1/2" from the rear of the boom and install the second button, snugging it
up into boom. DO NOT BOTHER WITH ACCURATELY CENTERING the element at this time and
DO NOT INSTALL the stainless steel internal locking “KEEPERS” yet. This is easier to do after all
the elements are installed in the boom.
3. Install the 3/16” rod DRIVEN ELEMENT as you did the reflector. Then continue with the installation
of the DIRECTORS. Note that the Director Elements do not consistently diminish in length
from rear to front, so pay close attention to length and position.
4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount the element
sticking out on each side of the boom. Once you have all the elements centered, sight down the
element tips from the rear comparing each side. Look for any obvious discrepancies and correct if
found.
5. Install the stainless steel SHAFT RETAINERS to secure the elements. NOTE: For portable or
temporary use of the antenna, the retainers may be left off. The button insulators, normally a tight
fit, hold the elements quite securely.
To install, use thumb and forefinger to hold the retainer over the end of the PUSH TUBE ( 3/8" x 3"
tube, supplied in the kit), internal fingers on retainer dished into tube. HOLD THE ELEMENT
FIRMLY TO PREVENT IT FROM SLIDING OFF CENTER and press the retainer onto the element
end and continue until retainer butts on insulator button. Locking pliers, lightly clamped up against
440-11X ASSEMBLY MANUAL
opposite button insulator will help maintain center reference. If you push the first retainer too far,
remove element from boom, push retainer completely off the element, and start over. Install
another retainer to the opposite side of the element. Continue installing retainers until all elements
are locked in place.
6. Mount the DRIVEN ELEMENT BLOCK to the boom using a single 8-32 X 1-1/4" screw and lock
washer. Orient the block with type “N” feed connector facing to the rear and balun connectors
facing to the front. Block orientation may be reversed if you wish to center mount antenna.
7. Attach balun and tighten the connectors gently using a 7/16" end wrench. A lot of torque is
unnecessary. Form the balun close to the boom and secure to boom with a nylon cable tie. Tie
should be snug but not crushing or kinking the coax.
8. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS.
Slide the bars onto the 3/16” rod driven element tips and 1/8” Driven Element Block Rods. Position
the Shorting Bars as specified on the Dimension Sheet: the distance given is between the outer
edge of the Driven Element Block and the inner edge of the Shorting Bar. Align the bars and rods
with each other and tighten the setscrews.
9. The boom to mast plate is normally mounted at the rear of the boom using 1" U-bolts and the
stainless locknuts provided. DO NOT OVER TIGHTEN. 2” U-bolts, cradles, and stainless hardware
are provided for mounting the antenna to your mast. Secure feed coax to boom and mast with
harness ties.
10. MOUNTING
THIS ANTENNA CAN BE REAR MOUNTED IN ANY POLARITY TO ANY TYPE OF 2” MAST.
IF YOU PLAN TO CENTER-MOUNT THE ANTENNA PLEASE FOLLOW THE GUIDELINES
BELOW:
Maintain good VSWR and pattern: Keep metallic masts, cross booms and the feed coax out of the
element plane.
FOR HORIZONTAL POLARIZATION, the antenna may be center-mounted to a metallic vertical mast
or a horizontal NON-METALLIC cross boom (no conductive material in element plane). If mounted
to a horizontal cross boom, route the feedline forward to the boom-to-mast plate, loop down at
right angles to the element plane, and bring back to cross boom at least 6” beyond element tips.
FOR VERTICAL POLARIZATION, the antenna may be center-mounted to a NON METALLIC
VERTICAL MAST (no conductive material in element plane) or a horizontal metallic cross boom. If
mounted to a vertical mast, route the feed line forward to the boom-to-mast plate, loop out at a
right angle to the boom, and bring down to the mast at least 6 inches BELOW THE ELEMENT
TIPS. The feedline may also exit at the rear of the boom and loop back to the mast.
Stacking? Call M2and let us help you DO IT RIGHT
THIS COMPLETES THE ANTENNA ASSEMBLY.
440-11X ASSEMBLY MANUAL
440-11X DIMENSION SHEET
DESCRIPTION.............................................................................................QTY
BOOM SECTION, 1 X .065 X 31” (M2ABS440-11X-1).................................1
BOOM SECTION, 2 X .065 X 31” (M2ABS440-11X-2).................................1
ELEMENTS, 3/16 ROD x Dimension Sheet .................................................11
DRIVEN ELEMENT ASSEMBLY (SADEA432UHF-1)..................................1
BALUN, RG-6 1/2 WAVE .............................................................................1
BOOM-TO-MAST PLATE, .188 X 3” X 4” (M2APT0019).............................1
U-BOLT AND CRADLE, 2” ...........................................................................2
U-BOLT, 1” ...................................................................................................2
ASSEMBLY MANUAL ..................................................................................1
IN HARDWARE BAG:
SHORTING BAR (M2ASB0080)...................................................................2
BUTTON INSULATORS...............................................................................22
KEEPER, SS ................................................................................................22
NUT, 5/16-18 SS ..........................................................................................4
LOCK WASHER, 5/16 SS ............................................................................4
LOCKNUT, 1/4-20 SS ..................................................................................4
SETSCREW, 8-32 X 1/4, SS........................................................................4
SCREW, 8-32 X 1-1/4 SS.............................................................................3
LOCKNUT, 8-32” SS ....................................................................................2
LOCK WASHER, #8 SS ...............................................................................1
CABLE TIE, NYLON ....................................................................................2
ALLEN HEAD WRENCH, 5/64”....................................................................1
PUSH TUBE, 3/8 X 3” ..................................................................................1
Carefully manufactured by:
M2 ANTENNA SYSTEMS, INC.
4402 N. Selland Ave.
Fresno, CA 93722
(559) 432-8873 Fax: 432-3059
www.m2inc.com Email: sales@m2inc.com
440-11X PARTS & HARDWARE
Indice
Altri manuali M2 Antenna Systems Antenna
M2 Antenna Systems
M2 Antenna Systems 6M5XHG Manuale utente
M2 Antenna Systems
M2 Antenna Systems 1700-26-2 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 6M3 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2M4X Manuale utente
M2 Antenna Systems
M2 Antenna Systems 420-50-11 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 44.5-5 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 40M1L Manuale utente
M2 Antenna Systems
M2 Antenna Systems 75-5AS Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2MXP20 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 6M5XHP Manuale utente
M2 Antenna Systems
M2 Antenna Systems FG170-230-5 Manuale utente
M2 Antenna Systems
M2 Antenna Systems FG2227-21X4CP Manuale utente
M2 Antenna Systems
M2 Antenna Systems 6.9-4CDD-125 Manuale utente
M2 Antenna Systems
M2 Antenna Systems FD35.5 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 7-10-30LP8 UP-KIT Manuale utente
M2 Antenna Systems
M2 Antenna Systems 678-14 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 915XBISP Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2M5-440XP Manuale utente
M2 Antenna Systems
M2 Antenna Systems 40M3C Manuale utente
M2 Antenna Systems
M2 Antenna Systems 300XP12 Manuale utente
Manuali Antenna popolari di altre marche
Alfa Network
Alfa Network APA-L01 Manuale utente
Naval
Naval PR-422CA Manuale utente
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuale utente
TERK Technologies
TERK Technologies TV44 Manuale utente
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuale utente
HP
HP J8999A Manuale utente
