M2 Antenna Systems 440-6SS Manuale utente
M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722
Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com
©2015 M2 Antenna Systems Incoporated 05/28/15
Rev.01
Model .........................................440-6SS
Frequency Range.......................420 To 450 MHz
*Gain ..........................................11 dBi
Front to back ..............................18 dB Typical
Beamwidth ...............................E=55° H=65°
Feed type ...................................Gamma Match
Feed Impedance........................50 Ohms Unbalanced
Maximum VSWR........................1.5:1
Input Connector..........................SO-239
Power Handling..........................500 Watts
Boom Length / Dia......................36” / 1”
Maximum Element Length..........13-5/8”
Turning Radius:..........................34-1/8”
Stacking Distance.......................27” High & 30” Wide
Mast Size....................................1-1/2” to 2” Nom.
Wind area / Survival...................0.3 Sq. Ft. / 75 MPH
Weight / Ship Wt.........................3 Lbs. / 4 Lbs.
M2 Antenna Systems, Inc.
Model No: 440-6SS
FEATURES:
New licensed Hams will find the 440-6SS a low cost, medium performance antenna to be a great choice for a starter an-
tenna without compromising quality. A single heavy duty mounting cradle and stainless steel hardware, give you the confi-
dence of quality construction you have come to expect from M2. Built with size and portability in mind, this antenna is
great for Field Days, Mountain Topping, Fox Hunts, DXpeditions and ATV use. The antenna breaks down to no more than
36” long, making it a natural for trips.
SPECIFICATIONS:
*Subtract 2.14 from dBi for dBd
Tools handy for assembly process: Phillips head screwdriver, 5/16”,11/32” spin-tight or socket, 7/16”
end wrenches / sockets, measuring tape.
1. This antenna uses a one-piece boom that will be rear mounted.
2. Lay out the elements by length and position as shown on the DIMENSION sheet. Start with the
reflector (longest) element and push on a black button insulator to about 1/2” from the center of the
element. Push the reflector element through the element hole towards the rear of the boom. (Refer
to the DIMENSION sheet for proper placement) Install the second button insulator on the other
side of the element, pushing it up into boom. DO NOT BOTHER WITH ACCURATELY
CENTERING the element at this time and DO NOT INSTALL the stainless steel internal locking
keepers yet. This is easier to do after all of the elements are installed in the boom.
3. Install the DRIVEN ELEMENT in the same way as you did the reflector element. Then continue
with the installation of the DIRECTOR or DIRECTORS.
4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount of each
element sticking out on each side of the boom. Once you have all of the elements centered, sight
down the element tips from the rear comparing each side. Look for any obvious discrepancies and
correct if found.
5. Install the stainless steel keepers to secure the elements.
NOTE: For portable or temporary use of the antenna, the
keepers may be left off. The button insulators, (normally a tight
fit) hold the elements quite securely.
To install, use thumb and forefinger to hold the keeper over the
end of the PUSH TUBE. Make sure that the internal fingers of
the keeper are dished into the push tube. HOLD THE
ELEMENT FIRMLY TO PREVENT IT FROM SLIDING OFF
CENTER and press the keeper onto the element end and
continue until the keeper is snug on the insulator button.
Locking pliers, lightly clamped up against the opposite button insulator, will help maintain center
reference. If you push the first keeper too far, remove the element from the boom, push the keeper
completely off the element, and start over. Install another keeper to the opposite side of the
element. Continue installing keepers until all elements are locked in place.
6. Next, assemble the Gamma Match assembly. Start by sliding a
#6 flat washer over the end of the Gamma Feed block stud.
7. Slide the Gamma Insulator over the Gamma Rod, leaving 1/8”
of the insulator exposed beyond the end of the Gamma Rod.
Slide this Gamma Rod and Insulator over the end of the
Gamma Feed block stud.
8. Now, slide a #6 lock washer over the Gamma Feed block stud
and finish the assembly with a 6-32 nut. *Note* The connector
stud can spin freely. Use a pair of needle nose pliers or a small
wrench to hold the flat surface when tightening.
9. Next, attached the Gamma Match assembly to the boom, using a single 8-32 x 1 1/4” screw. Make
sure to orient the Feed connector towards the rear of the antenna.
10. Now slide the Gamma Tube over the Gamma Insulator and refer to the DIMENSION sheet for
proper placement.
Installing Keepers
440-6SS ASSEMBLY MANUAL
11. Install the two halves of the Shorting Bar onto the Gamma Tube and the driven element below.
Refer to the DIMENSION sheet for proper location of the shorting bar. Tighten the shorting bar in
place using a single 8-32 x 7/8” screw and lock nut.
12. Now Slide the 3/8” x 3/8” Vinyl cap over the Gamma Tube until it is flush with the end of the
Gamma Tube.
13. At this point it is important to determine whether your antenna will be mounted horizontally (SSB/
CW) or Vertically (FM). Locate the two sets of holes at the rear of the antenna.
14. Insert the 2” u-bolt into the uni-cradle and slide this assembly into one of the two sets of holes on
the rear of the boom. Finish the assembly by installing (2) 1/4” lock washers and 1/4-20 nuts.
15. MOUNTING FOR HORIZONTAL OR VERTICAL POLARIZATION
Route the feed line coax towards the rear of the antenna past the reflector element and onto your
mast. Secure the feed line coax to the antenna boom with the supplied nylon ties. When
mounting the antenna vertically polarized, make sure to orient the gamma tube with the
vinyl cap facing up.
To maintain good VSWR and antenna pattern: Keep metallic masts, cross booms and the feed line
coax out of the element plane.
Stacking or Phasing ? Call us and let us help you DO IT RIGHT.
THIS COMPLETES THE ANTENNA ASSEMBLY.
Carefully manufactured by:
M2ANTENNA SYSTEMS, INC.
4402 N. Selland Ave.
Fresno, CA 93722
(559) 432-8873 Fax: 432-3059
440-6SS ASSEMBLY MANUAL
440-6SS ASSEMBLY DETAILS
440-6SS DIMENSION SHEET
DESCRIPTION ................................
QTY
BOOM SECTION, 1 X .058 X 36”...........................................1
ELEMENTS, 3/16 ROD X SEE DIM SHEET...........................6
GAMMA CONNECTOR BLOCK ASSEMBLY.........................1
GAMMA ROD, 3/16 X 2.0 ALUM ROD ..................................1
GAMMA TUBE, 3/8 X .058 X 1.750 ALUM TUBE...................1
GAMMA INSULATOR, .1/4 X .031 X 1.625 TEFLON TUBE...1
VINYL CAP, 3/8 X 3/8 ............................................................1
UNI CRADLE..........................................................................1
U-BOLT, 2” SS........................................................................1
ASSEMBLY MANUAL.............................................................1
HARDWARE BAG:
SHORTING BAR, 1/4 X 3/8 X 1.688.......................................2
BUTTON INSULATORS, 3/16 ................................................12
KEEPERS, 3/16 SS................................................................12
SCREW, 8-32 X 1.25 SS ........................................................1
SCREW, 8-32 X .875 SS ........................................................1
LOCKNUT, 8-32 SS................................................................1
FLATWASHER, #6 SS............................................................1
LOCKWASHER, #6 SS...........................................................1
NUT, 6-32 SS..........................................................................1
LOCKWASHER, 1/4 SS..........................................................2
NUT, 1/4-20 SS.......................................................................2
NYLON TIE, 7 3/4 ..................................................................3
PUSH TUBE, 3/8 X 3”.............................................................1
Carefully manufactured by:
M2ANTENNA SYSTEMS, INC.
4402 N. Selland Ave.
Fresno, CA 93722
(559) 432-8873 Fax: 432-3059
440-6SS PARTS & HARDWARE
Indice
Altri manuali M2 Antenna Systems Antenna
M2 Antenna Systems
M2 Antenna Systems 249CP24 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2MXP20 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 20M4DX Manuale utente
M2 Antenna Systems
M2 Antenna Systems 902-5 YAGI Manuale utente
M2 Antenna Systems
M2 Antenna Systems Eggbeater EB-310 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2MCP8A Manuale utente
M2 Antenna Systems
M2 Antenna Systems 80M1L Manuale utente
M2 Antenna Systems
M2 Antenna Systems 500-1000-10 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 248CP22A Manuale utente
M2 Antenna Systems
M2 Antenna Systems DCN100-500 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 348CP18 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2MCP22 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 17M5DX Manuale utente
M2 Antenna Systems
M2 Antenna Systems 2M4 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 6-30LP11 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 40M4LLDD Manuale utente
M2 Antenna Systems
M2 Antenna Systems 295XP6 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 436CP30 Manuale utente
M2 Antenna Systems
M2 Antenna Systems 915XBISP Manuale utente
M2 Antenna Systems
M2 Antenna Systems EB-144/RK2M Manuale utente
Manuali Antenna popolari di altre marche
Alfa Network
Alfa Network APA-L01 Manuale utente
Naval
Naval PR-422CA Manuale utente
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuale utente
TERK Technologies
TERK Technologies TV44 Manuale utente
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuale utente
HP
HP J8999A Manuale utente
