Macsense MPC-200 Manuale utente
User’s Manual
Fast Ethernet CardBus
(MPC-200)
R
acsense
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Driver support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Quick Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing the Fast Ethernet CardBus Card . . . . . . . . . . . . . . . . . . . . .2
Setup for Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Setup for Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Chapter 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing the Fast Ethernet CardBus Card . . . . . . . . . . . . . . . . . . . . .5
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
README.TXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Chapter 3 Driver Installation for Windows 95 OSR 2 . . . . . . . . . . . . .7
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Check Version of Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Check CardBus Driver's Version . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Advanced Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connection Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Receive Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Snooze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hot Swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Chapter 4 Driver Installation for Windows 98 . . . . . . . . . . . . . . . . . . .15
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Upgrading Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
i
Advanced Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Chapter 5 Driver Installation for Windows NT 3.5.1 . . . . . . . . . . . . . .21
Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
NDIS 3 Driver Parameters for Windows NT 3.51 . . . . . . . . . . . . . . . .22
Chapter 6 Driver Installation for Windows NT 4.0 . . . . . . . . . . . . . . . .23
Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Chapter 7 Client Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .27
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Driver Installation Brief Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Dos ODI Client Driver Installation NetWare 3.x/4.x Client . . . . . . . . . .28
NDIS Driver For Windows for Workgroups 3.11 . . . . . . . . . . . . . . . . .30
NDIS Driver For LAN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Appendix A Troubleshooting for Windows Environment and PCI
CardBus bridge Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Windows 95 OSR 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
PCI CardBus Bridge Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Appendix B PCI to CardBus Bridge Utilities . . . . . . . . . . . . . . . . . . .37
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Utilities Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Typical Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
PCI to CardBus Bridges Supported . . . . . . . . . . . . . . . . . . . . . . . . . .41
Appendix C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Appendix D Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
RJ-45 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
ii
Chapter 1 Introduction
This manual describes how to operate the Fast Ethernet CardBus Card. The Fast
Ethernet CardBus Card is a Credit-card sized Ethernet Card which works with any comput-
er, notebook, sub-notebook or Card Reader that supports CardBus slots.
CardBus is a function and performance extension of the PC Card (PCMCIA) stan-
dards. The CardBus interface is a 32-bit wide and Bus-mastering allowable device. It
enhanced the overall system throughput.
This Fast Ethernet CardBus Card could be connected to either 100Mbps Fast Ethernet
or 10Mbps Ethernet network.
¥ For operating in a 100Mbps (100BASE-TX) Fast Ethernet network, a Category 5
unshielded twisted pair (UTP) cable or Category 1 shielded twisted pair (STP) cable
should be used.
¥ For operating in a 10Mbps (10BASE-T) Ethernet network, a Category 3,4, or 5
(UTP) cable or Category 1 shielded twisted pair (STP) cable could be used.
Features
¥ CardBus form factor for CardBus equipped portable PCs
¥ IEEE 802.3 for 10BASE-T and IEEE 802.3u for 100BASE-TX compliant
¥ Automatically negotiates 10Mbps or 100Mbps connection speed, depending on
speed of the network
¥ Provides full-duplex to enhance throughput
¥ Offer high performance 100Mbps networking via 32-bit, PCI CardBus slot
¥ Complies to PC Card 1995 CardBus standards
¥ Switch less design and software configurable card setting
¥ 68-pin connector for attachment to PC's CardBus slot, and 15-pin flat connector to
media coupler
¥ 3.3V low power consumption
¥ LEDs monitoring indicators
Network Interface
¥ RJ-45 to connect with 10BASE-T or 100BASE-TX Hub or Switch
Driver Support
¥ NDIS2 for Novell NetWare DOS ODI
¥ NDIS2 for Windows for Workgroups 3.11
¥ NDIS2 for Microsoft LAN Manager
¥ NDIS3 for Microsoft Windows NT 3.51
Introduction
1
Chapter 1 Introduction
¥ NDIS4 for Microsoft Windows 95 OSR2, and Windows 98
¥ NDIS4 for Microsoft Windows NT 4.0
Physical Characteristics
¥ Standard Conformance: IEEE 802.3 for 10BASE-T
IEEE 802.3u for 100BASE-TX
¥ Host Interface: PC Card 95 CardBus Standard
¥ Ethernet Data Speed: 10Mbps and 100Mbps (Auto-Negotiation)
¥ Bus Width: 32 bits
¥ Power: 3.3 V
¥ Temperature: 0ûC~60ûC/ 32ûF~140ûF (Std. Operating)
¥ Humidity: 10% to 90%
¥ Distance: 100m from Hub to Node
¥ Dimensions: 86mm x 54mm x 5 mm
Quick Installation
Installing the Fast Ethernet CardBus Card
You will be installing the Fast Ethernet CardBus Card in your computer. If you are
having trouble locating the slot, refer to your computer's user's manual or consult the
manufacture of your computer.
Gently slide the PC Card into the PC Card slot. Make sure the Card is firmly seated in
the socket and you are ready to setup and install the network drivers.
For a connection to a Fast Ethernet network, use a Category 5 unshielded twisted pair
(UTP) or Category 1 shielded twisted pair (STP) cable with RJ-45 connector to connect
with 100Mbps port of a hub or switch.
For a connection to a 10BASE-T Ethernet network, use a Category 3,4 or 5 UTP or
STP 1 cable with RJ-45 connector to connect with 10Mbps port of a hub or switch.
Setup for Windows 95
Windows 95 OSR2 (OEM Service Release #2) and later versions contain all drivers
necessary for accessing your Fast Ethernet CardBus Card. Before the installation, please
follow these steps to check the version of Windows 95 and CardBus driver.
1. Click the Start button and select Settings .
2. Click Control Panel , and double-click the System icon.
3. Select General . The version of Windows 95 will be displayed under the
system field. Remember, only 4.00.950b and later versions (4.00.950c or 4.00.951)
fully support CardBus.
Introduction
2
4. Select Device Manager, click PCMCIA
socket
, then select one CardBus controller
and click Properties .
5. Click Driver, and select Driver File Details
...
.
6. CBSS.VXD will be found and its version must be 4.10.1387 or later.
If your CardBus driver is older, please contact your Windows 95 supplier for updating
to the latest version.
After getting the correct version, just follow these steps to get up and running:
1. Start the computer.
2. Insert the Fast Ethernet CardBus Card into a PC Card slot in your computer. Make
sure the card is securely inserted into the socket. Windows will display the Update
Device Driver Wizard dialog box. Click next, select Other Locations button and
key in A:/ in the location, where the device information file (.inf file) can be found.
Insert Ethernet Driver Diskette into driver A and click OK. Windows will find the Fast
Ethernet CardBus Card.
3. Click Finish to start installing the necessary drivers.
4. Follow the instructions of Windows 95 to install the Ethernet Driver Diskette in
drive A and Windows 95 CD-ROM in CD-ROM driver.
5. After installing the desired drivers, the Ethernet adapter will be enabled, and the
LED indicator will be turned on if network is available.
Setup for Windows 98
In the case of Windows 98, you do not need to check the version of your Operating
System. Windows 98 supports CardBus drivers for many kinds of CardBus controllers and
drivers for the Digital Semiconductor LAN Controller 2114x family. Taking the advantages
of these new characteristics and the Plug & Play feature, you can simply hot plug your
Fast Ethernet CardBus Card into the CardBus socket of your notebook and follow the
instructions showed on the screen to finish the installation process. As the manufacturer of
this Fast Ethernet CardBus Card, we do know some notebook computers have problems
to drive this card by using the driver that come with Windows 98. But mostly they could be
solved by upgrading this card driver to one supplied in you driver diskette.
Upgrading steps:
1. Start the computer.
2. Insert the Fast Ethernet CardBus Card into a PC Card slot in your computer. Make
sure the card is securely inserted into the socket. Double-click the System icon
from the Control Panel. Select Device Manager, then double-click PCI Fast
Ethernet DEC 21143 BASEd Adapter from Network adapters and select Update
Driver from PCI Fast Ethernet DEC 21143 Based Adapter Properties.
3. Windows will display the Update Device Driver Wizard dialog box. Click next. Then
select Display a list of all the drivers in a specific location
, so you can select
the drive you want
. Click next. Then, Windows will display the Select Device dialog
box. Click Have Disk and then key in A:/ for the location of where the device infor-
mation file (.inf file) can be found. Insert the Fast Ethernet CardBus Card Driver
Introduction
3
Diskette into drive A and click OK. Windows will find the Fast Ethernet CardBus
Card .
4. Click Next to start installing the necessary drivers.
5. Type A: / for the location of where the files are stored in the
Copying Files
dialog
box and click OK.
6. Click Finish to complete the installation process.
7. Follow the instructions of Windows 98 to restart your computer.
8. After installing the desired drivers and restarting on Windows 98, the Ethernet
adapter will be enabled, and the LED indicators will be turned on if network is avail-
able
Introduction
4
Chapter 2 Getting Started
Installing the Fast Ethernet CardBus Card
You will be installing the Fast Ethernet CardBus Card in CardBus slot of your comput-
er. If you have trouble locating the slot, please refer to your computer's userÕs manual or
consult the manufacture of your computer.
Follow the procedure below to install the Fast Ethernet CardBus Card.
1. Turn off the host computer.
2. With the card's 68 pin connector facing the PCMCIA CardBus slot, gently slide the
PC Card into the CardBus slot. Make sure the card is firmly seated in the socket
3. Plug the Ethernet adapter cable to the 15-pin connector on the Fast Ethernet
CardBus Card as in the following figure below.
4. Connect your Ethernet adapter cable to the network using a RJ-45 cable.
5. Power on your notebook computer.
6. Now you are ready to install your communication software as described in the
following chapters.
LED Indicators
¥ 100 LED: This LED is used to indicate the Ethernet speed: The green light
indicates a connection with a 100BASE-TX Fast Ethernet network.
¥ Link/Act LED: This LED is used to indicate the network activity. It is blinking when
Hardware Installation
5
the PC Card is transmitting or receiving packets from network. It is
also lit when a Link to the network is acquire.
README.TXT
There is one file named Readme.txt on driver diskette which provides the information
about this Driver Diskette's contents and installation guide. This file is located in the root
directory of the diskette.
Hardware Installation
6
Chapter 3 Driver Installation for Windows 95 OSR 2
System Requirements
Windows 95 may come with most of the drivers necessary for accessing your Ethernet
card, but only OSR2 (OEM Service Release #2) and later versions fully support CardBus
adapters. Before the installation, please follow the steps below to check the version of
Windows 95 and CardBus drivers.
Check Version of Windows 95
1. Click the Start button and select Settings.
2. Click Control Panel, and double-click the System icon.
3. Select General. The version will be displayed under the system field. Remember,
only 4.00.950b and later versions (4.00.95c or 4.00.951) fully support CardBus.
Check CardBus Driver's Version
1. Select Device Manger, then click PCMCIA socket, then select one CardBus
controller, and click Properties. The following diagram is an example for a TI PCI-
1130 CardBus controller.
Driver Installation for Windows 95 OSR 2
7
Altri manuali per MPC-200
1
Indice
Altri manuali Macsense Scheda di rete
Manuali Scheda di rete popolari di altre marche
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
Hama
Hama 49276 Manuale utente
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo
Compaq
Compaq Wireless LAN 100 Manuale utente
Bose
Bose PowerMatch Dante Manuale utente