Macurco CME1-FTG Manuale utente

Macurco™Aerosol CO Field Test Gas CME1-FTG

User Instructions

IMPORTANT: Keep these User Instructions for reference.

Intended Use

The CME1-FTG is an 11L 500 ppm Aerosol Carbon Monoxide Field Test Gas that can be used with the

Macurco CM-E1 and CM-6 CO detectors. This field test gas allows installers to do a quick functionality test of

the CO sensor. The flow rate of the CME1-FTG is 10 Lpm so you will have about a minute of gas or enough to

test 20-30 sensors.

Specifications

CME1-FTG Carbon Monoxide Field Test Gas 11L 500ppm CO/Air, Aerosol, 10LPM

Field Test Procedures CM-6

Caution:

Units to be tested must be powered continuously for a minimum of 3 minutes before proceeding.

For optimum test results the unit should be in clean air and be in a low ambient air flow.

Check that the CM-6 status indicator light is illuminated, Green continuously. If not, do not proceed

with tests. See CM-6 Trouble Indicator section.

1. The display option should be set to “On” and reading 0 ppm in clean air.

2. With the cover in place, direct the gas into the housing by placing the nozzle of the aerosol can onto the

sensor grate area (under DO NOT PAINT) and press for 2 to 3 seconds.

3. Wait for a few seconds. The digital display should climb indicating the increased CO concentration at the

sensor confirming a pass of the quick test.

Note: If the Display does not change within 10 seconds, there are four possibilities:

a. The gas is empty, expired or degraded, replace the gas cylinder.

b. The gas was not directed into the housing (direct the gas into the housing by placing the nozzle of

the aerosol can onto the sensor grate area and re-test).

c. Unit needs to be re-calibrated (go through the Field Calibration Procedure and re-test).

4. Wait for the display to return to 0 ppm and configure options to desired settings.

Testing the Fan Relay

Note: The time to activate the Fan relay depends on the delay setting.

1. With the display function turned “On”, the CM-6 will show the current concentration of CO or “0” (zero) in

clean air.

2. With the cover in place, direct the gas into the housing by placing the nozzle of the aerosol can onto the

sensor grate area (under DO NOT PAINT) and press for 2 to 3 seconds.

3. When the CO concentration reaches the Fan Relay setting (35 ppm, for example) the display will flash back

and forth between “FAn” and “35”. With the display function turned ”Off”, the display does not show the CO

concentration, but will show “FAn” as long as the fan relay is activated.

Note: If the Fan relay does not close within a few seconds, there are six possibilities:

a. The gas is empty, expired or degraded, replace the gas cylinder.

b. The gas was not directed into the housing (direct the gas into the housing by placing the nozzle of

the aerosol can onto the sensor grate area and re-test).

c. The gas concentration at the sensor did not reach the Fan relay activation level. Set Fan relay to

25ppm and repeat the test.

d. Detector has Fan relay set to disable (OFF) or 100ppm. Set Fan relay to 25ppm and repeat the

test.

e. The Fan relay delay (Frd) setting is at 3 minutes. Set the Fan relay delay to zero (0) minutes.

f. Unit needs to be re-calibrated (go through the Field Calibration Procedure and re-test).

4. Wait for the display to return to 0 ppm and configure options to desired settings.

Testing the Alarm Relay

Note: The CO concentration to activate the Alarm relay depends on the setting.

1. With the display function turned “On”, the CM-6 will show the current concentration of CO or “0” (zero) in

clean air.

2. With the cover in place, direct the gas into the housing by placing the nozzle of the aerosol can onto the

sensor grate area (under DO NOT PAINT) and press for 4 to 5 seconds.

3. When the CO concentration reaches the Fan relay setting, the Fan relay should activate according to the

settings.

4. When the CO concentration reaches the Alarm Relay setting, (200 ppm, for example) the display will flash

back and forth between “ALr” and “200”. The buzzer will sound indicating “Alarm” if the buzzer is turned

“On”. With the display function turned off the display does not show the CO concentration, but will show

“ALr” when the Alarm relay is activated.

Note: If the Fan relay does not close within a few seconds, there are five possibilities:

a. The gas is empty, expired or degraded, replace the gas cylinder.

b. The gas was not directed into the housing (direct the gas into the housing by placing the nozzle of

the aerosol can onto the sensor grate area and re-test).

c. The gas concentration at the sensor did not reach the Alarm relay activation level. Set Alarm relay

to 50 and repeat the test.

d. Detector has Alarm relay set to disable (OFF) or 200ppm. Set Alarm relay to 50ppm and repeat the

test.

e. Unit needs to be re-calibrated (go through the Field Calibration Procedure and re-test).

5. Wait for the display to return to 0 ppm and configure options to desired settings.

Testing the 4-20mA current loop

1. With the display function turned “On”, the CM-6 will show the current concentration of CO or “0” (zero) in

clean air.

2. With the cover in place, direct the gas into the housing by placing the nozzle of the aerosol can onto the

sensor grate area (under DO NOT PAINT) and press for 4 to 5 seconds.

3. The Fan relay should activate according to the settings.

4. The Alarm relay should activate according to the settings.

5. The 4-20 mA output should ramp up from 4mA in clean air to 20mA at 200 ppm.

Note: If the 4-20mA output does not ramp up within a few seconds, there are four possibilities:

a. The gas is empty, expired or degraded, replace the gas cylinder.

b. The gas was not directed into the housing (direct the gas into the housing by placing the nozzle of

the aerosol can onto the sensor grate area and re-test).

c. Detector has 4-20 mA option set to “OFF”. Set 4-20mA option to “On” and repeat the test.

d. Unit needs to be re-calibrated (go through the Field Calibration Procedure and re-test).

5. Wait for the display to return to 0 ppm and configure options to desired settings.

See the complete Macurco CM-6 User Instructions for factory settings, trouble codes, calibration and testing.

MACURCO FIXED GAS DETECTION PRODUCTS LIMITED WARRANTY

Macurco™, warrants the CME1-FTG field test gas will be free from defective materials and workmanship for a period of

two (1) years from date of manufacture (indicated on the gas bottle label), provided it is maintained and used in

accordance with Macurco instructions and/or recommendations. If any component becomes defective during the warranty

period, it will be replaced or repaired free of charge, if the unit is returned in accordance with the instructions below. This

warranty does not apply to units that have been altered or had repair attempted, or that have been subjected to abuse,

accidental or otherwise. The above warranty is in lieu of all other express warranties, obligations or liabilities. THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO A

PERIOD OF ONE (1) YEARS FROM THE PURCHASE DATE. Macurco shall not be liable for any incidental or

consequential damages for breach of this or any other warranty, express or implied, arising out of or related to the use of

said gas detector. Manufacturer or its agent’s liability shall be limited to replacement or repair as set forth above. Buyer’s

sole and exclusive remedies are return of the goods and repayment of the price, or repair and replacement of non-

conforming goods or parts.

Manufactured by Aerionics, Inc.

Sioux Falls, SD

Email: [email protected]

Phone: 1-877-367-7891

Rev 05.07.2014

Macurco is a trademark of Aerionics, Inc.

Indice

Altri manuali Macurco Apparecchiature di prova

Macurco

Macurco AimSafety PM 100 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente