Magnum M9-RSB-12 Manuale utente
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3 - Hudson, OH 44236 - phone 330.915.2382 - fax 330.529.5279 - www.magnum-innovations.com - info@magnum-innovations.com
INSTALLATION & CONFIGURATION
TOP VIEW:
5.5625” 4.4375”
1”
2.75”
LEFT SIDE:
RIGHT SIDE:
MAGNUM SENSOR CONTROL BOARD
• PRODUCT CASING & DIMENSIONS
• TECHNICAL DATA
Part Numbers (Frequency Dependant) M9-RSB-12 (902 MHz - North America)
M8-RSB-12 (868 MHz - Europe and China)
MJ-RSB-12 (928 MHz - Japan)
Input Power 24 VAC
Digital Relay Output Channels (3) N.O. Dry Contracts Rated for 24 VAC 2A
Analog Output Channels (1) 0-10 VDC Rated for 30mA
Digital Input Channels (2) (24 VAC / 24 DC) (Source / Sink)
Pressure Measurement (2) (3 Wire / Pressure Transducer) (Source / Sink)
Temperature Measurement (9) (2 Wire NTC 10K)
Humidity Measurement (1) (3 Wire / Humidity Sensor 0-100%) (Source / Sink)
Wireless Protocol EnOcean Wireless Standard
Wireless Range 150 (50-150 typical)
Enclosure ABS Plasc
Dimensions 5.5625” x 2.75” x 1”
Operang Temperature -40°F to 125°F (-40°C to 51.667°C)
Storage Temperature 32°F to 104°F (0°C to 32°C)
*PATENT PENDING
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3 - Hudson, OH 44236 - phone 330.915.2382 - fax 330.529.5279 - www.magnum-innovations.com - info@magnum-innovations.com
INSTALLATION & CONFIGURATION
INPUT / OUTPUT OVERVIEW:
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
T1 GND
0-10V
Relay Out 3
Relay In 3
Relay Out 2
Relay In 2
Relay Out 1
Relay In 1
GND
Pressure 2
24VDC
GND
Pressure 1
24VDC
Digital Input 2
24VDC
Digital Input 1
24VDC
24VAC Input, COMM
24VAC Input, HOT
T2
T3
T4
T5
T6
T7
T8
T9
T10 Humidity Power
Digital 1
Digital 2
Pressure 1
Pressure 2
Temp
MAGNUM SENSOR CONTROL BOARD
• CONNECTING INPUTS & OUTPUTS
1. BEFORE INSERTING ANY SENSORS OR WIRES INTO DEVICE, BE SURE TO LOOSEN SCREWS THROUGH THE HOLES ON THE TOP OF THE
DEVICE.
2. INSERT WIRES INTO CORRECT RECEPTACLE ON THE SIDE OF THE DEVICE (see images above), AND THEN TIGHTEN SCREWS TO
SECURE THE WIRES.
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3 - Hudson, OH 44236 - phone 330.915.2382 - fax 330.529.5279 - www.magnum-innovations.com - info@magnum-innovations.com
MAGNUM SENSOR CONTROL BOARD
INSTALLATION & CONFIGURATION
1 INTRODUCTION
2 INSTALLATION
The Magnum Temperature / Humidity / Pressure Sensor Control Board includes 2 digital inputs, 3 digital outputs and 1 analog output.
When a 24 VAC power source is connected to the Magnum Sensor Control Board, the controller automacally makes the 3 relays,
pressure sensors, 0-10 Volts, and two digital inputs available.
The Control Board Includes:
- 24VAC / 24 VDC power connecons
- 9 NTC 10K Temperature sensor input channels / 1 Humidity
- 2 Digital inputs
- 3 Digital outputs
- 1 Analog output
1. BEFORE POWERING DEVICE , connect all sensors and digital inputs / outputs (SEE INPUT / OUTPUT OVERVIEW BELOW)
2. Connect device to a power source
(Green LED should light up to conrm device is powered “ON” as shown in image below)
3. Device Mounng:
NOTE: Mounng environment should have a typical ambient temperature (32°F - 104°F (0°C - 32°C) and relave humidity
levels (20% - 95% non-condensing).
- Device can be wall mounted or mounted directly on the refrigeraon case (on top or side of case)
- Use 1/8” screws to mount device to desired locaon
- See image below for proper screw locaon on the plasc casing.
LED is GREEN
(POWER IS “ON”)
1/8” Screw
Locaon 1/8” Screw
Locaon
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3 - Hudson, OH 44236 - phone 330.915.2382 - fax 330.529.5279 - www.magnum-innovations.com - info@magnum-innovations.com
3 DEVICE CONFIGURATION
AIRCONFIG™ IS REQUIRED TO CONFIGURE THIS DEVICE. PLEASE FOLLOW THE STEPS BELOW TO DOWNLOAD AIRCONFIG™ AND BEGIN
YOUR DEVICE’S CONFIGURATION
Step One
• Download airConfig™, based on your operating system, to your computer at download.magnum-innovations.net
Step Two
• Insert USB stick, specifically programmed by Magnum Innovations, into your computer
Step Three
• Power up your device prior to configuration
Step Four
• Your laptop / computer (with provided USB stick) must be within radio range to configure device
Step Five
• Start airConfig™ and select “Advanced” tab
MAGNUM SENSOR CONTROL BOARD
INSTALLATION & CONFIGURATION
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3 - Hudson, OH 44236 - phone 330.915.2382 - fax 330.529.5279 - www.magnum-innovations.com - info@magnum-innovations.com
4 RESPONSIBILITY & RESIDUAL RISKS
5 DISCLAIMER
Magnum Innovaons shall not be liable for damages caused by or aributed to the user including, but not limited to the following:
• Unauthorized installaon and / or use that does not comply with the safety standards specied in applicable regulaons and
/ or in this document.
• Use on equipment that does not guarantee adequate protecon against electric shocks, water or dust when assembled.
• Use on equipment that allows dangerous parts to be accessed without the use of tools.
• Installaon and / or use on equipment that is not compliant with the current standards and regulaons in force.
Magnum Innovaons shall not be liable for damages originated from the installaon and / or use of the soware that does not com-
ply with the instrucons of this manual.
While reasonable eorts have been made in the preparaon of this document to ensure accuracy, Magnum Innovaons assumes no
liability resulng from the informaon contained herein.
To the maximum extent permied by law, Magnum Innovaons assumes no liability for special, accidental, direct, indirect, con-
sequenal, exemplary or punive damages (including, without any limitaon whatsoever, the loss of income or prots, interrupon of
work, loss of data or goodwill) originang from the use or failure of the soware or equipment or from the supply or failure to supply
technical support, even when informed of the likeliness of said damages.
To the maximum extent permied by law, in no event shall the liability of Magnum Innovaons exceed the amount paid to Magnum
Innovaons for the quanes of it’s products giving rise to the liability.
MAGNUM SENSOR CONTROL BOARD
INSTALLATION & CONFIGURATION
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Magnum Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
