Maker Factory MAKEVMP400 Manuale utente

MAKEVMP400

3.5" 320 x 480 TOUCHSCREEN FOR RASPBERRY PI®(ILI9341)

USER MANUAL

MAKEVMP400

V. 03 –14/01/2020 2

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could

harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it

should be taken to a specialized company for recycling. This device should be returned to your

distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Please read the manual thoroughly before bringing this device into service. If the device was damaged in

transit, do not install or use it and contact your dealer.

2. Safety Instructions

•This device can be used by children aged from 8 years and above, and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning the use of the device in a

safe way and understand the hazards involved. Children shall not play with the device.

Cleaning and user maintenance shall not be made by children without supervision.

•Indoor use only.

Keep away from rain, moisture, splashing and dripping liquids.

3. General Guidelines

•Familiarise yourself with the functions of the device before actually using it.

•All modifications of the device are forbidden for safety reasons. Damage caused by user

modifications to the device is not covered by the warranty.

•Only use the device for its intended purpose. Using the device in an unauthorised way

will void the warranty.

•Damage caused by disregard of certain guidelines in this manual is not covered by the

warranty and the dealer will not accept responsibility for any ensuing defects or

problems.

•The dealers cannot be held responsible for any damage (extraordinary, incidental or

indirect) –of any nature (financial, physical…) arising from the possession, use or

failure of this product.

•Due to constant product improvements, the actual product appearance might differ from

the shown images.

•Product images are for illustrative purposes only.

•Do not switch the device on immediately after it has been exposed to changes in

temperature. Protect the device against damage by leaving it switched off until it has

reached room temperature.

•Keep this manual for future reference.

MAKEVMP400

V. 03 –14/01/2020 3

4. Overview

resolution ........................................................................................................... 320 x 480

LCD type ..................................................................................................................... TFT

LCD interface ................................................................................................................SPI

touch screen type ...................................................................................................resistive

backlight...................................................................................................................... LED

aspect ratio................................................................................................................... 8.5

5. Pin Layout

pin no.

symbol

description

1, 17

3.3 V

power positive (3.3 V power input)

2, 4

5 V

power positive (5 V power input)

3, 5, 7, 8, 10, 12, 13,

15, 16

6, 9, 14, 20, 25

GND

ground

TP_IRQ

touch panel interrupt, low level while the panel

detects touching

LCD_RS

instruction/data register selection

LCD_SI/TP_SI

SPI data input of LCD/touch panel

TP_SO

SPI data output of touch panel

RST

reset

LCD_SCK/TP_SCK

SPI clock of LCD/touch panel

LCD_CS

LCD chip selection, low active

TP_CS

touch panel chip selection, low active

6. Example

Required Hardware

•1 x Raspberry Pi®1/2/3 main board

•1 x microSD card (> 8 GB, image file ± 7.5 GB)

•1 x microSD card reader

•1 x micro USB cable

•1 x USB keyboard

•3.5” LCD module (VMP400)

Required Software

•SD formatter

•Win32Disklmager

•Raspberry Pi®OS IMAGE

•LCD Driver

MAKEVMP400

V. 03 –14/01/2020 4

1. Format the SD card. Open SDFormatter, select your SD card and click <Format>.

2. Burn the Raspberry Pi®OS IMAGE onto the SD card. Open Win32Disklmager, select the file and SD card,

and click <Write>. The burning process may take a few minutes.

3. Make the hardware connection. Connect the VMP400 screen to the Raspberry Pi®. Wait for the device to

switch on.

MAKEVMP400

V. 03 –14/01/2020 5

MAKEVMP400

V. 03 –14/01/2020 6

7. Driver Installation

7.1 Install the Raspbian official IMAGE.

Download the latest Raspbian IMAGE from the official website https://www.raspberrypi.org/downloads/.

Format the TF card with an SDFormatter.

Burn the official image onto the TF card using Win32DiskImager.

7.2 Obtain the LCD driver.

Online Installation

Log onto the Raspberry Pi®user system to command line (initial user name: pi, password: raspberry).

Get the newest driver from GitHub (the LCD should be connected to the Internet).

Offline Installation

Extract from the included CD-ROM or ask your seller.

Copy the LCD-show-160701.tar.gz drive to the Raspberry Pi®system root directory. Copy flash the driver

directly onto the TF card after installing the Raspbian IMAGE, or copy by SFTP or other remote copy

methods. Unzip and extract the driver files as the following command:

7.3 Install the LCD driver.

The corresponding execution for this 3.5” LCD:

The corresponding execution to switch back to the traditional HDMI display:

Wait for a moment after executing the above command before you can use the LCD.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also

in part, is prohibited.

This publication represents the technical status at the time of printing.

git clone https://github.com/goodtft/LCD-show.git

chmod -R 755 LCD-show

cd LCD-show/

cd /boot

sudo tar zxvf LCD-show-160701.tar.gz

cd LCD-show/

sudo ./LCD35-show

sudo ./LCD-hdmi

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Maker Factory Unità di controllo

Maker Factory

Maker Factory MAKEVMA308 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA312 Manuale utente

Maker Factory

Maker Factory MAKEVMA404 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA307 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA310 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA411 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA313 Manuale utente

Maker Factory

Maker Factory ARDUINO MAKEVMA316 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente