Marmitek SMM31 Manuale utente

USER MANUAL

MM3

20458/20120313 • SMM31™

SMM31

™

Shutter Switch Micromodule

SMM31 3

TABLE OF CONTENTS

SAFETY WARNINGS ............................................................... 4

HOW DOES MARMITEK X-10 WORK? .................................. 5

ADRESSES ............................................................................... 5

SIGNAL RANGE....................................................................... 6

SHUTTER SWITCH MICRO MODULE...................................... 8

FUNCTIONS............................................................................. 8

INTRODUCTION...................................................................... 9

INSTALLATION ....................................................................... 9

PROGRAMMING................................................................... 10

FREQENTLY ASKED QUESTIONS.......................................... 11

TECHNICAL DATA ................................................................ 13

DECLARATION OF CONFORMITY........................................ 15

COPYRIGHTS ........................................................................ 16

SAFETY WARNINGS

xThe wiring of your electrical installation is live (230 V)

and extremely dangerous. Never connect the module

when plugged into the mains. Always turn off the

main switch before starting the installation.

xThis product is for professional use and should be

installed by a certified installer."

xTo prevent short circuits, this product should only be

used inside and only in dry spaces. Do not expose the

components to rain or moisture. Do not use the

product close to a bath, swimming pool etc.

xDo not expose the components of your systems to

extremely high temperatures or bright light sources.

xIn case of improper usage or if you have altered and

repaired the product yourself, all guarantees expire.

Marmitek does not accept responsibility in the case of

improper usage of the product or when the product is

used for purposes other than specified. Marmitek

does not accept responsibility for additional damage

other than covered by the legal product

responsibility.

xThis product is not a toy. Keep out of reach of

children.

xDo not open the product: the device may contain live

parts. The product should only be repaired or serviced

by a qualified expert.

xAutomatic switching devices provide comfort, but can

also be dangerous. They can surprise people or can

ignite clothing hanging over an electric heat source.

Please be careful and take appropriate measures to

avoid accidents.

SMM31 5

HOW DOES MARMITEK X-10 WORK?

Marmitek X-10 components use the existing mains wiring

to communicate (using Marmitek X-10 signals). You can

build a complete system using the three different kind of

components of the Marmitek X-10 System:

1. Modules: These components will receive Marmitek X-10

signals and will switch or dim the attached lamp or

appliance. Examples of these modules are lamp modules

and appliance modules. These are available as build-in,

micro, DIN rail and plug-in modules.

2. Controllers: These components will transmit Marmitek

X-10 signals and thus will control the Modules.

3. Transmitters:Wireless components like remotes. The

signals of these components will be received by a

controller with transceiver functionality (IRRF 7243, TM13,

CM15Pro…..). The Transceiver will translate the signals into

Marmitek X-10 signals on the power line.

ADRESSES

Up to a maximum of 256 different addresses can be preset.

These are subdivided into a so-called HouseCode (A to P

incl.) and a UnitCode (1 to 16 incl.). The HouseCode can

also be set on the controllers, so that the controllers and

modules become part of the same system. The address can

be set either using code dials or by pressing buttons,

depending on the type of module.

The Marmitek X-10 System uses standard commands,

which control all units with the same HouseCode at the

same time (e.g. all lights on, all units off, etc.).

SIGNAL RANGE

Range of Marmitek X-10 signals over the Power Line

and how to increase the range.

The Marmitek X-10 System is based on power line

communication. The range of the Marmitek X-10 signals

very much depends on the local circumstances. On average

the range is a cable length of 80 meters.

If you have difficulties with the range of your

Marmitek X-10 signals, please pay attention to the

following facts:

1. When more than one phase is used for your electrical

system, it is necessary to couple these phases for the

Marmitek X-10 signals. For coupling you can use FD10

Phase Couplers/Filters. You only need to install a Phase

Coupler/Filter when your wall outlets and light switches

are divided over more than one phase (more than one

group is no problem). For bigger buildings or longer

distances we advice you to use an active repeater instead

of passive FD10’s.

2. It is possible that Marmitek X-10 signals are attenuated

by devices and lights which are connected to the power

line. In a normal home situation this effect is negligible

(the Marmitek X-10 system is using active gain control to

eliminate the effects). However, it is possible that a

particular device in your house is attenuating the signals so

much that the range of Marmitek X-10 signals is decreased

significantly. When you have range problems, it is wise to

try to locate the device which is attenuating the signals

simply by unplugging devices from the power line, and

testing the differences in range for your Marmitek system.

When e.g. your conclusion is that e.g. your computer

monitor is attenuating the signal, you can use a FM10

SMM31 7

Plug-in Filter between the power line and the monitor to

eliminate the effects.

Known devices which can cause attenuation are:

PC Monitors

PCs with heavy internal power supplies

Old Televisions

Copiers

Fluorescent Lights

Gas Discharge Lamps (Energy Saving Lamps)

3. Some (old) devices are able to disturb the signal by

transmitting noise on the power line. Because the

Marmitek X-10 signals are transmitted on 120 kHz, only

noise on or near this frequency will have influence on the

range. When you use a FM10 Filter to connect this device

to the power line, the noise will be filtered.

4. The Marmitek X-10 protocol has several mechanism to

avoid modules to be switched on or off by other sources

than your Marmitek X-10 Controllers. However, it is

possible that the Marmitek X-10 signals are disturbed by

e.g. baby phones which are in TALK mode (continuous

transmission). When these kind of signals are present on

the power line it is possible that the Marmitek X-10 signals

will not come through.

5. The mains do not stop at the front door of your home.

Everything that is attached to mains nearby your home can

have influence on Marmitek X-10 signals (e.g. heavy

machinery). If you think that your system is influenced by

devices out of your house, it is advisable to install FD10

Phase Coupler/Filter on each phase entering the house.

These filters will block signals coming into or going out of

your house, but will also match the impedance for the

mains. Hereby make your house Marmitek X-10 compatible

for these units. The FD10’s will not only filter but will also

couple the phases (please see 1).

Shutter Switch Micromodule

SMM31

Inp tu

Ad r ssde

On/ ffO*

LN 12

Shutter Switch Micromodule

SMM31

Inpt

Ad r ss

On/f

LN 12

SHUTTER SWITCH MICRO MODULE

Program

Button

RED

BLA

RED

BLA

Light

Indicator

PHASE

NEUTRAL

FUNCTIONS

xMakes your X-10 system invisible.

xInvisible installation built-in behind existing switches

or wall sockets. The module works with all makes and

types of switches, which means it can be used in every

interior and with all installations.

xQuick and easy to install and program.

xTransforms your existing 1- way standard rocker

switch into a X-10 controllable switch.

xMicromodule with built-in relay with two contacts for

connecting a 230V motor.

xCan be operated remotely with an X-10 signal or

locally, fully open/closed or on every interim position.

xLowers, in combination with the CM15Pro™ computer

interface, the sun blinds automatically during the day

in places where the sun shines inside. This way you

protect your furniture against the sunlight, keep the

house cool and simulate that you are at home.

xThe MicroModule uses one-way X-10 communication.

INTRODUCTION

This unit allows a motorized

blind to be controlled either

manually from a 1- way

standard rocker switch

connected to the unit, or

remotely by serial Marmitek

X-10 Powerline messages sent from a suitable controller.

When controlled serially the blind can be made to go to

intermediate settings in addition to fully up or fully down

with dim and bright commands.

INSTALLATION

xSwitch off appropriate mains fuse and master switch!

xImportant : 230V - 50Hz - 1A per channel max.

xTo install the SMM31, neutral and phase are required

at the installation point.

xTake the wall switch out of the wall box.

xDisconnect all wires from the switch.

xPull an additional Neutral wire if it is missing.

xConnect the phase and neutral wire to the “L” and

“N” terminals of the micromodule

xConnect the terminal 1 of SMM31 to Motor Down,

the terminal 2 to Motor Up.

xConnect the thin Black and Red wires of the built-in

module to the 1- way standard rocker switch.

xPosition the MicroModule against the back wall of

the wall outlet behind all the wires.

xYou are now able to program the MicroModule.

xFor more information see chapter “Programming”.

xInstall the 1- way standard rocker switch at its original

SMM31 9

place after the MicroModule is programmed.

xPlease note: due to heat generation, apply no more

than one module per flush socket / central socket!

PROGRAMMING.

WARNING: DO NOT FORGET TO TURN ON THE MAIN

MASTER SWITCH PRIOR TO PROGRAMMING.

Programming the address:

The factory setting for the SMM31 is to address A1.

Unlike most Marmitek X-10 Modules the SMM31 does not

have code wheels.

To change the address, the module needs to be set to the

program mode.

Press and hold the “Program” button for 5 seconds,

indicator light Turns ON, means entering “Program

mode”. Transmit the address command (xx ON or XX OFF),

at this time the indicator light goes OFF.

Warning! The MicroModule will leave the setup mode if it

doesn’t receive any commands within 30 seconds.

Indice

Altri manuali Marmitek Interruttore

Marmitek

Marmitek SWM1P Manuale utente

Marmitek

Marmitek CONNECT420 Manuale utente

Marmitek

Marmitek SWM1P Manuale utente

Marmitek

Marmitek Connect 310 Manuale utente

Marmitek

Marmitek Connect 621 UHD 2.0 Manuale utente

Marmitek

Marmitek AD10 Manuale utente

Marmitek

Marmitek SPEAKER ANYWHERE 350 Manuale utente

Marmitek

Marmitek Connect TS41 Manuale utente

Marmitek

Marmitek X10 SS12E Manuale utente

Marmitek

Marmitek CONNECT 411 Manuale utente

Marmitek

Marmitek Connect 720 Manuale utente

Marmitek

Marmitek Connect 350 UHD Manuale utente

Marmitek

Marmitek CONNECT 236 Manuale utente

Marmitek

Marmitek SW10 Manuale utente

Marmitek

Marmitek Connect 620 UHD 2 Manuale utente

Marmitek

Marmitek CONNECT 225 Manuale utente

Marmitek

Marmitek Connect 620 UHD 2.0 Manuale utente

Marmitek

Marmitek connect AE14 Manuale utente

Marmitek

Marmitek Connect 421 UHD Manuale utente

Marmitek

Marmitek CONNECT 410 Manuale utente

Marmitek

Marmitek SW12 Manuale utente

Marmitek

Marmitek SS13 Manuale utente

Marmitek

Marmitek Connect 310 Manuale di istruzioni

Marmitek

Marmitek Connect 310 UHD 2.0 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente