Mastech MAS830L Manuale utente

MAS830L MAS830

MAS830B MAS838

Instruction Manual

DIGITAL MULTIMETER

Introduction

The instrument of this series is a small hand-held 3 1/2 digital

multimeter featuring stable, highly reliable and anti-drop

performance. It is provided with a LCD display of 15 mm

height for clear reading. The circuit design takes LSI double

integral A/D converter as its core under the protection of an

overload protection circuit, making it a superior and handy

instrument. It can be used to measure DC and AC voltage, DC

current, resistance, diodes, transistors, temperature and for

in-circuit continuity test.

Measurement features of the types of this series:

Features

MAS

830L

MAS

830

MAS

830B

MAS

838

Alternating Voltage

measurement V~



Direct Voltage

measurement V



Direct Current

measurement A



Resistance

measurement 



Diode measurement



hFE test



Continuity checking with

buzzer



Data hold



Backlight



1. Display

3 1/2 digit, 7 segment, 15mm high LCD.

2. Back light (option)

When this button is pushed, the Back light of display is

on. After about 5 seconds, the Back light is self-off. The

Back light is on again, just push this button once.

3. Function and range switch

This switch is used to select functions and desired

ranges as well as to turn on/off the meter.

4. Hold function

When this button is pushed, the display will keep the

last reading and “ ” symbol will appear on the LCD

until pushing it again.

5. “10A” jack

Plug in connector for red test lead for 10A measurement

6. “COM” jack

Plug in connector for black (negative) test lead.

7. VmA jack

Plug in connector for red (positive) test lead for voltage,

resistance and current (except 10A) measurements

FRONT PANEL

Safety Information

MAS830B, MAS830L, MAS830B and MAS838 Digital

Multimeters are designed based on ICE61010 600V(CATII)

and pollution degree 2.

To ensure the safe and accurate use, please read the

instruction manual carefully.

Safety Signs

Important safety information. Read the manual.

High voltage with danger

Ground.

Double insulation (Class II safety equipment).

Fuse must be replaced as per the specification herein.

Notices



The instrument can only be used in conjunction with the

probe for the compliance with safety standards. If the

probe needs replacing due to damage, the replacement

must be of the same type or the same electrical

specifications.

Do not exceed the input limit specified for each range.

When the instrument is measuring, do not touch the

input terminal not in use.

When a measurement range is uncertain, turn the

function/range switch to the maximum range position.

Before turning the function/range switch, make sure the

probe is open with the circuit being measured.

Before on-line resistance measurement, turn off all

power and discharge all capacitors.

Be careful when taking measurement of voltage higher

than 60V DC/30V AC. Remember to keep your fingers

behind the hand shield of the probe.

When measuring a TV set or switch power supply,

watch for pulse in the circuit that may damage the

multimeter. 4

Before measuring any transistor, make sure the probe is

not connected to any circuit being measured.

Before taking the measurement of voltage with the

probe, make sure there is no element connected to the

test socket of the transistor.

Maintenance



Before removing the rear cover, disconnect the probe

from the circuit to be measured.

To protect the internal circuit, replace the fuse with one

of the same specifications:

F1 250mA / 250V

F2 10A / 250V

Don’t use the instrument until the rear cover is placed

back and the screws are tightened.

Clean the housing of the instrument only with a wet rag

dripped with little detergent but never chemical solution.

In case of the any abnormality, stop using it and sent it

for maintenance.

Technical data

Accuracy: % of reading 5 digits, one year warranty.

Ambient temperature: 18℃to 28℃

Ambient humidity: 80%.

General features:

Maximum voltage between

terminals and earth ground

CATⅡ600V

Fuse protection

F1 250mA/250V F2 10A/ 250V

Power

9V battery, NEDA 1604 or 6F22

Display

1999

Overrange Indication

“1”

Polarity indication

“-” for negative polarity

Operating Environment

0 to 40℃

Storage temperature

-10℃to 50℃.

Low battery indication

“ ”appears on the display

Size

138mm×69mm×31mm

Weight

170g.

Direct current voltage measurement

Range

Resolution

Accuracy

200mV

100V

0.5% of rdg 3 digits

1mV

0.5% of rdg 3 digits

20V

10mV

0.5% of rdg 3 digits

200V

100mV

0.5% of rdg 3 digits

600V

0.8% of rdg 5digits

Overload Protection: 200mV range: 250V dc or rms.

The rest range: 600V dc or rms.

Direct current measurement

Range

Resolution

Accuracy

20A

0.01A

1% of rdg 3 digits

200A

0.1A

1% of rdg 3 digits

2mA

1A

1% of rdg 3 digits

20mA

10A

1% of rdg 5 digits

200mA

100A

1.5% of rdg 3 digits

10A

10mA

3% of rdg 10 digits

Overload Protection: F1 200mA/250V Fuse F2 10A/ 250V

*MAS838, no 20A positon

Alternative voltage measurement

Range

Resolution

Accuracy

200V

100mV

1.2 % of rdg 10 digits

600V

1.2 % of rdg 10 digits

Overload Protection: 600V dc or rms.

Frequency range: 40Hz to 400Hz.

Display: Average(effective value of sinusoid)

RESISTANCE

Range

Resolution

Accuracy

200

0.1

0.8% of rdg 5 digits

2k

1

0.8% of rdg 2 digits

20k

10

0.8% of rdg 2 digits

200k

100

0.8% of rdg 2 digits

2M

1k

1.0% of rdg 5 digits

Maximum Open Circuit Voltage: 3.2V

Overload Protection: 250VDC or RMS.AC.

Diode and circuit on-off measurement

Range

Description

When the on-resistance is smaller than (70 30)),

the built-in buzzer will beep.

Display the approximate diode position voltage.

Overload Protection:250V DC or RMS.AC.

Temperature measurement

Range

Test Range

Measurement

Accuracy

℃

1℃

-20℃to 40℃

-0℃to 400℃

400℃to 1000℃

10% Range, 2 digits

1.0% Range, 3 digits

2.0% Range

TRANSISTOR hFE TEST (0-1000)

Range

Test Range

Test Current

Test Voltage

NPN & PNP

0-1000

Ib=10A

Vce=3V

Instructions

Notices before operation:

1. Plug the instruction, check the 9V battery, if it is slow, the

symbol will display, requiring battery replacement;

Otherwise follow the steps below.

2. The besides the probe jack indicates that the input

voltage or current should not exceed the specified limits to

protect the internal circuit.

3. Before measurement, turn the function/range switch to the

desired range.

Direct voltage measurement

Insert the red probe to the “V..mA” jack and the black

lead to the “COM” jack.

Turn the function/range switch to the range of V-and

connect the probe to the power supply or load to be

measured. The polarity touched by the red probe will be

on the display.

Direct current measurement

Place the black probe into the “COM” jack. For the

current to be measured not exceeding 220mA, put the

red one into the “V..mA” jack. For current to be

measured between 220mA and 10A, insert the red

probe into 10A jack.

Set the function/range switch to the desired A~ range,

and connect the probe in series with the load to be

measured. The current value and the polarity connected

to the red probe will be shown on the display.

Notice

1. If you do not knowthe measured voltage range in advance,

set the function/range switch to the maximum range, and

then gradually turn to smaller ranges until satisfactory

resolution.

2. If the display shows “1”, this indicates an overrange

measurement, and the switch should be set to a higher

range.

3. The symbol “”beside the probe indicates the

maximum input current is 200mA or 10A, depending on

the inserted jack. Overcurrent will blowthe fuse.

Notice

1. If you do not know the measured voltage range in advance,

set the function/range switch to the maximum range, and

then gradually turn to smaller ranges until satisfactory

resolution.

2. If the display shows “1”, this indicates an overrange

measurement, and the switch should be set to a higher

range.

3. Do not input a voltage of more than600V, it is capableof

indicating a higher voltage, but with the risk of damaging the

inside circuit.

4. When taking the measurement of high voltage, pay special

attention to avoid an electric shock.

Alternative voltage measurement

Place the red probe into the “V.. mA” jack and the

black probe into the “COM” jack.

Turn the switch to V~ and connect the probe to the

power supply or load to be measured.

Note: Refer to point 1, 2, 3 and 4 for direct current

voltage measurement.

Resistance measurement

Place the back probe into the “COM” jack and red one

into the “V/ / HZ”jack.

Turn the switch to the “COM” jack, and connect the

probe to the resistor being measured and read the

result on the display.

Diode measurement

Insert the black lead to the “COM” jack the red one into

the “V..mA” jack.

Connect the red test lead to “V..mA” jack and the

black Turn the switch to the range, and connect

the red probe to the positive pole of the diode being

measured and the black one to the negative pole, read

the approximate forward voltage drop of the diode on

the display.

Notice

1. If the resistor being measured is greater than the maximum

value of the selected range, the display will show “1”,

requiring the selection of a higher range. It normally takes a

few seconds for the reading to get stable when measuring a

resistor larger than 1M.

2. In default of input, for instance, open circuit, thedisplay

shows “1”.

3. When measuring an online resistor, de-energized the

circuit being measured and discharged capacitors.

Altri manuali per MAS830L

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Mastech Multimetro

Mastech

Mastech MS8238C Manuale utente

Mastech

Mastech MS8228 Manuale utente

Mastech

Mastech MS8251B Manuale utente

Mastech

Mastech M839b Manuale utente

Mastech

Mastech MS8265 Istruzioni per il montaggio

Mastech

Mastech MAS830L Istruzioni per il montaggio

Mastech

Mastech my68 Manuale utente

Mastech

Mastech MS8221C Manuale utente

Mastech

Mastech MS8239C Manuale utente

Mastech

Mastech MS8238B Manuale utente

Mastech

Mastech MS8211 Manuale utente

Mastech

Mastech MS8268 Manuale utente

Mastech

Mastech MS8228 Manuale utente

Mastech

Mastech MS8264 Istruzioni per il montaggio

Mastech

Mastech MS8236 Manuale utente

Mastech

Mastech MAS830B Istruzioni per il montaggio

Mastech

Mastech MS8321B Manuale utente

Mastech

Mastech MS8218 Manuale utente

Mastech

Mastech MS8240B Manuale utente

Mastech

Mastech MS8216 Manuale utente

Mastech

Mastech MS2208 Manuale utente

Mastech

Mastech MS5203 Manuale utente

Mastech

Mastech MS8251A Manuale utente

Mastech

Mastech M266 Series Istruzioni per il montaggio

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Fluke

Fluke 83 Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Fluke

Fluke 8846A Manuale operativo e di manutenzione

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente