Matrix T3x Guida per l'amministratore
T3x Error Codes LCD Console Board W / MEEEX LCB 1
Table of Contents
Page#
Error Code Description 2
MaintenanceLamp
BlueLight 2
RedLight 2
ServiceInformation 2-3
Serial Number Information 2
Engineering Mode 3
Speed Movement Related Errors 4-6
E1 Speed Feedback Issue 5
E1 Corrective Action Parts Needed 6
Console Memory Related Errors 7-8
E2MemoryLoss 8
E2 Corrective Action Parts Needed 8
Elevation Movement Related Errors 9-13
E3 Elevation Motor Signal Range / Stall 10
E3 Corrective Action Parts Needed 11
E6 Elevation Signal Missing 12
E6 Corrective Action Parts Needed 13
Notes:
If there are any safety concernes please call the Matrix Fitness Systems Service Department
at 866-693-4863 before performing any service.
Please make sure to take any saftey percautions before performing any service.
Unplug any electrical power cords before touching any electrical components.
Use common sense before performing any electrical service.
Do not touch any component that is “hot” or looks to be “hot”.
T
3X Error Codes
LCD Console Board W/ MEEEX LCB
1000324 Rev 1 8/1/05
T3x Error Codes LCD Console Board W / MEEEX LCB 2
ERROR CODES
Errors are divided in speed related errors (E1) , console memory related error (E2) , and elevation related errors (E3 /
E6). System should be properly calibrated (if possible) before attempting to troubleshoot error codes.
The following table contains standard error codes. Other error codes are enabled for development purposes but
cannot be remedied via engineering variables. Error codes can be remedied in some conditions by system calibration
or require toggle of system power to reset
MaintenanceLamp
Blue Light: Normal Opertation Mode: When the treadmills accumulated distace reaches the 5,000 mile mark
the Blue light will be displayed meaning the it is time for general maintenance to be performed. This light will
then come on at every 5,000 mile interval. To turn off the light after you have finished the maintenance hold
the incline ↓and the speed -at the same time for 3 seconds.
Red Light: Normal Operation Mode: This light will occure when there is a Error sent to the console display.
To fix this please see the Error Code guide number and follow the instruction on how to fix the problem.
Service Information
For faster service please have the following information ready.
Serial Number
Production Date:
This information is located on the front of the elevation rack.
Additional information needed:
Start Speed
Motor Decal information
Motor Pad under motor
CODE DESCRIPTION
1 Speed Range (usually caused by calibration)
Speed Stall (could be missing speed sensor)
AC power wires could be loose
2 Console Memory Loss
3 Elevation out of range / Elevation movement stall
6 Console signal to LCB but no movement
T3x Error Codes LCD Console Board W / MEEEX LCB 3
Recording Information Needed From Engineer Mode
Enter Engineer Mode hold down the ↑& + Use the ↓↑ arrows to select the P value.
keys for 3 seconds.
Once at the P Value use the - + to change the data. Once at the needed value press QUICK START to save.
To run Auto Check hold down the SELECT key
T3x Error Codes LCD Console Board W / MEEEX LCB 4
SPEED
MOVEMENT
RELATED
ERRORS
T3x Error Codes LCD Console Board W / MEEEX LCB 5
E1 - Speed Feedback Error
OVERVIEW
If no belt movement is detected 10 seconds after pressing START the console calls a speed stall error (E1).
During normal run time operation the value stored during auto calibration is used to initially set the speed (e.g. target speed = 12
MPH, PWM ticks = Maximum PWM = 999). Once the speed is stabilized the actual speed is monitored and if different than the
target speed the PWM value is adjusted until the actual speed matches the target speed. If the PWM value is changed by more
than the amount of ticks required to change .8 MPH and the actual speed does not match the target speed then an (E1) error is
flagged. This error indicates the motor controller system is unable to maintain the target speed.
Solution Flow
Chart
T3x Error Codes LCD Console Board W / MEEEX LCB 6
E1 CORRECTIVE ACTION PARTS NEEDED
Part Number: SJFD08020 (110V)
Description: Motor Control Board, 110v (T3x)
Drawing Number: M02
Part Number: MC0501144E
Description: Console Extended Cable (T3x)
Drawing Number: P01
Part Number: MC0502066C
Description: Console Wire (T3x)
Drawing Number: P02
Part Number: SJTD01008BB
Description: Console Control Board (T3x)
Drawing Number: AY1
Part Number: SZTM68MTR
Description: T3x Motor
Drawing Number: M01
Part Number: MCA206002
Description: MTR Brush T3x
Drawing Number: See MTR Drawing
Qty:2
Part Number: MC0510091B
Description: Speed Sensor T3x
Drawing Number: P05
T3x Error Codes LCD Console Board W / MEEEX LCB 7
CONSOLE
MEMORY
RELATED
ERRORS
T3x Error Codes LCD Console Board W / MEEEX LCB 8
E2 – Console Memory Loss
OVERVIEW
If the console memory chip is damaged or has some sort of electrical spike the console memory could be lost. If so you will need to
replace the console board.
E2 CORRECTIVE ACTION PARTS NEEDED
Part Number: SJTD01008BB
Description: Console Control Board (T3x)
Drawing Number: AY1
T3x Error Codes LCD Console Board W / MEEEX LCB 9
ELEVATION
MOVEMENT
RELATED
ERRORS
T3x Error Codes LCD Console Board W / MEEEX LCB 10
E3– Elevation Range / Elevation Stall
OVERVIEW
When elevation movement is commanded (e.g. elevation up) the elevation position feedback is expected to change in the correct
direction (e.g. increase in pot value for an elevation up command). If the elevation position feedback changes in the opposite of the
expected direction (e.g. elevation command up and elevation feedback decreases) a reverse elevation error (E3) is flagged.
To prevent the elevation from stalling at the lower travel end or running off on the top end of travel the elevation position feedback is
monitored. If the elevation position feedback is lower than expected (e.g. < 10) or higher than expected (e.g. > 250) then an (E3) is
called. To reduce the risk of elevation motor/system damage or overheating in the event of a stall elevation stall conditions are
monitored. If movement is commanded and the position feedback indicates no movement-taking place an elevation stall error is
called. This problem has been caused most frequently by overheated elevation motor.
Solution Flow Chart
Altri manuali per T3x
1
Indice
Altri manuali Matrix Tapis roulant
Matrix
Matrix MX-T5x Manuale utente
Matrix
Matrix T5X GROUP TRAINING Manuale utente
Matrix
Matrix MX-T3x Manuale utente
Matrix
Matrix MX-T3x Manuale utente
Matrix
Matrix LIVESTRONG T1xLS Manuale utente
Matrix
Matrix T1x Manuale di manutenzione
Matrix
Matrix T1xe-02(AC) Manuale utente
Matrix
Matrix T7XI-01 Manuale utente
Matrix
Matrix T3xe Manuale utente
Matrix
Matrix S-DRIVE PERFORMANCE TRAINER Manuale utente
Matrix
Matrix T3xe Manuale utente
Matrix
Matrix T50x-02 Manuale utente
Matrix
Matrix T3xe Manuale utente
Matrix
Matrix T3xm Manuale utente
Matrix
Matrix TOUCH XL Manuale utente
Matrix
Matrix T130 XI Manuale utente
Matrix
Matrix COMMERCIAL SERIES TREADMILL Manuale utente
Matrix
Matrix T1x Manuale utente
Matrix
Matrix T7xi Manuale utente
Matrix
Matrix t3x-03 Manuale utente
