Maxim MAX5022EVKIT Istruzioni operative e di manutenzione

General Description

The MAX5022 evaluation kit (EV kit) is a fully assembled

and tested 5W flyback-converter circuit board. The

power supply is configured for an isolated +5VDC out-

put voltage that can supply up to 1A of current. The line

input voltage range is from 85VAC to 265VAC or

120VDC to 375VDC.

The MAX5022 EV kit demonstrates high efficiency up to

80% at 262kHz switching frequency. This high efficiency

is achieved by using a single transistor (MOSFET),

flyback-converter topology providing output power up to

5W. The surface-mount transformer has a tertiary wind-

ing to power the MAX5022 IC after startup. An optocou-

pler along with the transformer provide input-to-output

isolation up to 4500VDC.

Warning: The MAX5022 EV kit is designed to operate

with high voltages. Dangerous voltages are present on

this EV kit and on equipment connected to it. Users

who power up this EV kit or the power sources connect-

ed to it must be careful to follow safety procedures

appropriate for working with high-voltage electrical

equipment.

Under severe fault or failure conditions, this EV kit may

dissipate large amounts of power, which could result in

the mechanical ejection of a component or component

debris at high velocity. Operate this kit with care to

avoid possible personal injury.

Features

♦85VAC to 265VAC or 120VDC to 375VDC Input

Range

♦Isolated Output Voltage: +5VDC at 1A

♦Input-to-Output Isolation Up to 4500VDC

♦Fully Assembled and Tested

♦Efficiency Up to 80%

♦2% Output Voltage Regulation Over Line and

Load

Evaluates: MAX5022

MAX5022 Evaluation Kit

________________________________________________________________ Maxim Integrated Products 1

19-2073; Rev 3; 4/05

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

Ordering Information

PART TEMP RANGE IC PACKAGE

MAX5022EVKIT 0°C to +70°C 6 SOT23-6

Component List

DESIGNATION QTY DESCRIPTION

C1, C9 2

10.0µF ±20%, 400V aluminum

electrolytic capacitors (12.5mm x

13.5mm)

Sanyo 400CV10FS

C2, C3 2

0.22µF ±20%, 50V X7R ceramic

capacitors (1206)

TDK C3216X7R1H224M

C4, C10 2

47µF ±20%, 6.3V aluminum organic

capacitors (case V)

Kemet A700V476M006AT018

C5, C12 2

0.01µF ±10%, 16V X7R ceramic

capacitors (0402)

TDK C1005X7R1C103K

C6 1

0.1µF ±10%, 50V X7R ceramic

capacitor (0603)

TDK C1608X7R1H104K

DESIGNATION QTY DESCRIPTION

C7 1 1000pF ±20%, 4KVAC (DE0910)

Murata DE1E3KX102MA5BA01

C8 1

8200pF ±10%, 50V X7R ceramic

capacitor (0603)

TDK C1608X7R1H822K

C11 1

1000pF ±10%, 630V X7R ceramic

capacitor (1206)

TDK C3216X7R2J102K

C13 1

2200pF ±10%, 50V X7R ceramic

capacitor (0402)

TDK C1005X7R1H222K

D1 1

250mA, 75V high-speed switching

diode (SOT-23)

Central Semiconductor CMPD914

Evaluates: MAX5022

MAX5022 Evaluation Kit

2 _______________________________________________________________________________________

DESIGNATION QTY DESCRIPTION

D2 1

3A, 40V Schottky power rectifier

(SMC)

Central Semiconductor CMSH3-40

D3 1

1000V, 1A full-wave diode bridge

(SMDIP)

Central Semiconductor CBR1-D100S

D4 1 600V, 1A ultra-fast rectifier (SMA)

Central Semiconductor CMR1U-06M

D5 1

100V, 200mA small-signal diode

(SOD-123)

Fairchild Semiconductor MMSD4148

F1 2 2AG and 5mm fuse clips

Keystone 3519

F1 1 1/4A 250V SLO-BLO fuse

Littelfuse 229.250H

L1, L3 2

Ferrite beads 220Ωat 100MHz, 2A

DCR = 0.050Ω(0805)

Murata BLM21PG221SN1

L2 1 470µH, 240mA inductor

Sumida CDRH73-471

N1 1

1.8A, 600V, n-channel MOSFET

(DPAK)

Fairchild Semiconductor SSR2N60B

R1, R2 2 360kΩ±5% resistors (1206)

DESIGNATION QTY DESCRIPTION

R3 1 1.00kΩ±1% resistor (0805)

R4 1 24.9kΩ±1% resistor (0805)

R5 1 8.06kΩ±1% resistor (0805)

R6 1 10Ω±5% resistor (0603)

R7 1 1.78Ω±1% resistor (1206)

R8 1 1.2kΩ±5% resistor (1206)

R9 1 240kΩ±5% resistor (0805)

R10 1 10Ω±5% resistor (0805)

R11 1 1.5kΩ±1% resistor (0603)

R12 1 100kΩ±5% resistor (1206)

R13 1 100Ω±5% resistor (0603)

TB1 1 2-point terminal block (0.2in center)

T1 1

480µH (primary:secondary:tertiary

turns ratio 60:3:8) 5W transformer

Cooper Electronic Technologies

CTX03-15256

U1 1 MAX5022EUT-T (6-pin SOT23)

U2 1

70V, 100% to 200% CRT

phototransistor (0.4in lead spacing)

Fairchild CNY17-3.W

U3 1

1.24V precision shunt regulator

(SOT23-5L)

Texas Instruments TLV431AIDBV

— 4 Rubber bumpers

— 1 MAX5022 EV kit PC board

Component List (continued)

Evaluates: MAX5022

MAX5022 Evaluation Kit

_______________________________________________________________________________________ 3

Quick Start

The MAX5022 EV kit is fully assembled and tested.

Follow these steps to verify board operation.

Warning: Exercise CAUTION when connecting and

measuring off-line voltages.

• Voltage at the primary side may be as high as

700VDC.

• Do not turn on the power supply until all connec-

tions are completed.

• Wear protective eye gear at all times.

• Do not touch any part of the circuit with bare hands

or conductive materials while power is applied.

• Make sure all high-voltage capacitors are fully dis-

charged before handling.

Recommended Equipment

• Isolation transformer

• Variac

• Voltmeter

VOUT Setup Procedure

1) Connect the positive lead of a DC voltmeter to the

VOUT pad.

2) Connect the negative lead of a DC voltmeter to the

GND pad.

3) Make sure that the isolation transformer is not pow-

ered up. Connect the variac to the output of the iso-

lation transformer.

4) Connect one lead of an AC voltmeter to the wiper

terminal of the variac.

5) Connect the other lead of the AC voltmeter to the

“common” terminal of the variac.

6) Set the output voltage of the variac to 0VAC.

7) Connect the wiper terminal of the variac to the L ter-

minal of TB1.

8) Connect the “common” terminal of the variac to the

N terminal of TB1.

9) Connect a 50Ω1W resistor across the output.

10) Power up the isolation transformer, and gradually

increase the voltage of the variac to 85VAC and up

to 265VAC.

11) Verify that VOUT is +5V throughout the input volt-

age range of 85VAC to 265VAC.

SUPPLIER PHONE FAX WEBSITE

Central Semiconductor 631-435-1110 631-435-1824 www.centralsemi.com

Cooper-Coiltronics 561-752-5000 561-742-1178 www.cooperet.com

Fairchild Semiconductor 888-522-5372 Local rep only www.fairchildsemi.com

Kemet 864-963-6300 864-963-6322 www.kemet.com

Keystone Electronics 800-221-5510 718-956-9040 www.keyelco.com

Littelfuse 847-824-1188 847-391-0894 www.littelfuse.com

Murata 770-436-1300 770-436-3030 www.murata.com

Sanyo Electronic Device 619-661-6835 619-661-1055 www.sanyodevice.com

Sumida USA 847-545-6700 847-545-6720 www.sumida.com

TDK 847-803-6100 847-390-4405 www.component.tdk.com

Note: Indicate that you are using the MAX5022 when contacting these component suppliers.

Component Suppliers

Evaluates: MAX5022

MAX5022 Evaluation Kit

4 _______________________________________________________________________________________

MAX5022 EFFICIENCY

0100 200 300 400 500 600 700 800 900 1000

EFFICIENCY (%)

OUTPUT CURRENT (mA)

VIN = 85VAC

VIN = 120VAC

VIN = 265VAC

Figure 1. Efficiency Graph

Detailed Description

The MAX5022 EV kit is an off-line 5W flyback converter,

configured for +5VDC/1A output. A tertiary winding

from the transformer is used to power the device during

normal operation. The secondary winding provides the

+5VDC output and can supply up to 1A.

This EV kit uses the MAX5022, a SOT23, current-mode,

pulse width modulating (PWM) controller. This PWM

controller varies the duty cycle to compensate for the

variation in VIN and the output load to maintain a con-

stant output voltage. The duty cycle determines the

on/off duration of the MOSFET (N1). The n-channel

MOSFET is used as a switch to control the current

through the primary winding of the transformer (T1).

The duty cycle is controlled by the feedback loop con-

sisting of voltage-divider resistors (R4, R5), a shunt regu-

lator (U3), an optocoupler (U2), and the PWM compara-

tor inside the MAX5022. This network provides the isolat-

ed feedback, regulating the output voltage to 5V ±2%

with up to 4500VDC input-to-output isolation.

The MAX5022 senses the current going through the

transformer’s primary winding with a current-sense

resistor (R7), and shuts down the output when the out-

put current exceeds the current limit of 1.6A. The

MAX5022 EV kit is protected against catastrophic fail-

ure with the fuse (F1).

Evaluates: MAX5022

MAX5022 Evaluation Kit

_______________________________________________________________________________________ 5

TERMINAL BLOCK

TB-1

TB-2

470µH

1.2kΩ

10µF

400V

10µF

400V

360kΩ

R12

100kΩ

C11

1000pF

360kΩ

0.22µF

789

1000pF

47µF

6.3V

1kΩ

R10

10Ω

0.01µF

8.06kΩ

24.9kΩ

0.1µF

C10

47µF

6.3V

+5V

VOUT

GND

10 1112

CTX03_15256

10ΩR7

1.78Ω

8200pF

NDRV

VIN

VCC

R11

1.5kΩ

C12

0.01µF

0.22µF

U2-B

240kΩ

OPTO

GND

MAX5022

SECONDARY GROUND

PRIMARY GROUND

NOTE: ALL RESISTORS ARE 5% UNLESS OTHERWISE SPECIFIED

100Ω

U2-A

R13

C13

2200pF

Figure 2. MAX5022 EV Kit Schematic

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

6_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

Evaluates: MAX5022

MAX5022 Evaluation Kit

Figure 3. MAX5022 EV Kit Component Placement Guide—Component Side

Figure 4. MAX5022 EV Kit PC Board Layout—Component Side

Figure 5. MAX5022 EV Kit PC Board Layout—Solder Side

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

MAX5022EVKIT

Indice

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente