MBot Cube Manuale utente
Welcome to use MBot Cube 3D Printer
Please check all the accessories one by one in the package, any missing or
damage, Please contact sales representative within 7days of receiving the MBot
cube kit.
Have any problem during assembling or other query contact us at
suppor[email protected]
A3
A6
A1 A 2
A4
A7
A9
A8
A5
前
抵挡板 Bottom dam-board
A9
panel
打印板 玻璃制品
4
Build plate
G14
黄铜柱
tray
Brass barrel
nut
nut
Washer
工具包
1 2 3
J
注意：
检查主板上的驱动小班，
必须和图示上的位置一致，
单打印头插4块，
分别为X、Y、Z、A。
Attention:
Tool box
Control button planel cable
L
Control button panel
protector
Cable wrap
Make sure the stepper
motor drivers chips are in
the right position.
Note:
Only 4 stepper motor
drivers chip for single head
3d printer.
er
G 2 m3 x8m m
6PCS
G 3 m3 x12 mm
4PCS
G 7 m3 x30 mm
4P CS
G 9 m3
9PCS
G 1 2 m3 C5 m3x7x20mm
4P CS 4P CS
G 4 m3 x16 mm
1PCS
A6 I6
G3
X2
G15
G4
X4
G7
X4
G2
X2
I7
G3
X2
G2
X4
G9
X2
G9
X2
A9 I1
C5
X4
A8
G12
X4
C1
X3
1
Assemble all the
electronics
components and
C1 stick to the
correct position.
A8
G9
X
G3
X
A8 A1
G9
X
G3
X
C3
C3
I2
G3
X2
G3
X4
G9
X2
G9
X4
I3
C7
X4
G6
X4
C7
X2
G 9
6PCS
G 3 m 3x1 2 mm
PCS6
G 1 5 m3
4P CS
2
注意：
按键(i3)安装时，注意插口在下方。
Attention:
i
2
2
2
2
Keep the cable connector socket of control
button pannel (i3) downside when assembling.
Y Axis Assembly
G3 X4
G9 X2
I4
C6 X2
G5 X2
G3
G9 X4
A8
C4
C3
x3
C2
G3
X轴限位开关
正面
背面
G12
G12
C2
A4
G9
G 3 m3 x12 mm
6P CS
G 5 m3 x20 mm
2P CS
G 9
8P CS
G 1 2 m 3
PCS2
3
X-axis limit switch
front
back
I4
G9
C6
X2
X2
C5
X2
A2
G12
X4
C5
X4
I5
F5
A5
G7
X4
G 7 m 3x3 0mm
4P CS
G 9 m 3
2P CS
G 3 m 3x1 2mm
2P CS
G 1 2 m3
4P CS
C6 3x7x12
2PCS
C6 3x7x20
4PCS
4
5
注意：
电机先不要坚固。
Attention:
Don’t fasten screw on
the motor too tight.
Altri manuali per Cube
2
Indice
Altri manuali MBot Stampante 3D
