Mcube MC3672 Istruzioni operative e di manutenzione

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 1 / 19
© 2018 mCube Inc. All rights reserved.
GENERAL DESCRIPTION
The MC3672 is an ultra-low power, low
noise, integrated digital output 3-axis
accelerometer with a feature set optimized
for wearables and consumer product
motion sensing. Applications include
wearable consumer products, IoT devices,
user interface control, gaming motion input,
electronic compass tilt compensation for
cell phones, game controllers, remote
controls and portable media products.
The EVA3672A is a prebuilt circuit board
with MC3672 WLCSP 3-axes sensor. The
MC3672 has internal sample rate from 14 to
1300 samples / second and measures
acceleration with a wide usage range, from
+/-2g up to +/-16g, and 6-bit to 14-bit high
precision ADC output, which is easy to fit
on top of the microcontroller, such as an
Arduino. The accelerometer communicates
via I2C and gives out motion detection or
sample acquisition conditions to trigger an
interrupt toward a MCU.
The sensor data is easily readable by
connecting DVDD to 3.3V, GND to ground,
and SCL/SDA pins to your Arduino I2C
clock and data pin respectively. Download
the MC3672 library from GitHub onto the
board, run the example sketch, and then
sensor data shortly comes out in raw data
count and SI unit accelerometer
measurements. An easy-to-use
demonstration on EVA3672A using the
Arduino platform is included in this
document.
MC3672 FEATURES
Range, Sampling & Power
•±2,4,8,12 or 16g ranges
•8, 10 or 12-bit resolution with FIFO
o14-bit single samples
•Sample rate 14 - 1300 samples/sec
•Sample trigger via internal oscillator,
clock pin or software command
•Sniff and Wake modes
•0.4 μA Sniff current @ 6Hz
•Separate or combined sniff/wake
•Ultra-Low Power with 32 sample
FIFO
o0.9 μA typical current @ 25Hz
o1.6 μA typical current @ 50Hz
o2.8 μA typical current @ 100Hz
o36 μA typical current @ 1300Hz
Simple System Integration
•I2C interface, up to 1 MHz
•SPI Interface, up to 8 MHz
•1.29 × 1.09 × 0.742 mm 8-pin
WLCSP package
•Single-chip 3D silicon MEMS
•Low noise to 2.3mg RMS

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 2 / 19
© 2018 mCube Inc. All rights reserved.
TABLE OF CONTENTS
1General Operation ........................................................................................................... 3
2Assembly and Test.......................................................................................................... 6
3Demo............................................................................................................................... 8
4Library Reference.......................................................................................................... 11
5Downloads..................................................................................................................... 15
6Schematics.................................................................................................................... 16
7Fabrication print............................................................................................................. 17
8Revision History............................................................................................................. 18
9Legal.............................................................................................................................. 19

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 3 / 19
© 2018 mCube Inc. All rights reserved.
1 GENERAL OPERATION
1.1 PINOUTS
1.2 POWER PINS
DVDD –3.3V Power Supply Input
GND –Ground Pin for Power and Logic
1.3 I2C PINS
Connect the SCL (I2C clock pin) to your microcontroller’s I2C clock line. This pin can be
used with 3V logic. A 4.7K pull-up resistor is required for this pin. Simply, add a 4.7K pull-
up resistor on R4 to make the I2C clock signal works normally.
Connect the SDA (I2C data pin) to your microcontroller’s I2C data line. This pin can be
used with 3V logic. A 4.7K pull-up resistor is required for this pin. Simply, add a 4.7K pull-
up resistor on R5 to ensure functionality of the I2C data signal.

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 4 / 19
© 2018 mCube Inc. All rights reserved.
R4, R5: If using I2C and I2C pull-up resistors are needed for your application then
install~4.7KΩ resistors into R4 (SCL clock pin) and R5 (SDA data pin) which are not
installed by factory default. In addition, besides soldering resisters on R4/R5, you can add
axial lead 4.7K ohm resistors to the SDA and SCL pin respectively. It will work the same
either way.
NOTE: DO NOT install more than one setup pull-up resistors per I2C bus.
1.4 SPI PINS
With an SPI connection, there is always one master device (usually a microcontroller)
which controls the peripheral devices. Typically, there are three wires commonly
connected to all the devices:
Connect the SCS (Slave Select) to the pin on the device that the master can use to enable
and disable SPI cycles.
Connect the SCL (Serial clock) to the pin where the clock pulses synchronize data
transmission generated by the master
Connect SDO to the pin where the Slave sends data to the master (Master Input, Slave
Output).
Connect SDA to the pin where the Master sends data to the peripherals (Master Output,
Slave Input).

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 5 / 19
© 2018 mCube Inc. All rights reserved.
1.5 INTERRUPT PINS
INT - HW interrupt signal pin. This pin will be triggered by the device when data is ready
to read, or a motion event is detected by the accelerometer. (Not currently supported in
the library for the interrupt pin, so please check the datasheet for the I2C commands and
related registers).

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 6 / 19
© 2018 mCube Inc. All rights reserved.
2 ASSEMBLY AND TEST
Please note that the SPI and I2C interfaces cannot both be active at the same time as
the clock (SCK) and data (SDA) are shared between the two protocols.
2.1 I2C INTERFACE
The EV3672A evaluation board can be easily wired to any microcontroller. This example
shows a typical Arduino UNO platform. For other microcontrollers, be sure it has I2C with
repeated-start support, then port the code. Please refer to the illustration below to connect the
related pins.
•Connect DVDD to the power supply, 3.3V. (Providing higher voltage, like 5V may
damage the sensor).
•Connect GND to common power/data ground.
•Connect the SCL pin to the I2C clock SCL pin on your Arduino.
•Connect the SDA pin to the I2C data SDA pin on your Arduino.
The MC3672 has a default I2C address of 0x4C and it can be changed to 0x6C by tying
the DOUT pin to VDD.

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 7 / 19
© 2018 mCube Inc. All rights reserved.
2.2 SPI INTERFACE
The EV3672A evaluation board can be easily wired to any microcontroller. This example
shows a typical Arduino UNO platform. Please refer to the illustration below for connecting the
related pins and then port the code to get the raw X, Y, Z sensor data.
•Connect DVDD to the power supply, 3.3V. (Providing higher voltage, like 5V may
damage the sensor.)
•Connect GND to common power/data ground.
•Connect SCL to digital I/O pin 13 as Serial Clock.
•Connect SDO to digital I/O pin 12 as Master Input, Slave Output.
•Connect SDA to digital I/O pin 11 as Master Output, Slave Input.
•Connect SCS to digital I/O pin 10 as Slave Select.

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 8 / 19
© 2018 mCube Inc. All rights reserved.
3 DEMO
3.1 DOWNLOAD THE DRIVER FROM GITHUB
To begin reading sensor data, you will need to download the MC3672 Library from the
GitHub repository. Do this by visiting the GitHub repository and manually downloading or
simply click this button the attached URL to download the zip file.
https://github.com/mcubemems/Accelerometer_MC36XX
Rename the uncompressed folder Accelerometer_MC36XX and check that the
Accelerometer_MC36XX folder consisting of MC36XX.cpp and MC36XX.h
If you need the sensor running on SPI, please configure the bus as SPI in the
MC36XX.h shown as below. Otherwise, the default is I2C bus.
//#define MC36XX_CFG_BUS_I2C
#define MC36XX_CFG_BUS_SPI
SPI could support 8MHz speed if high speed mode is enabled as below.
#define SPI_HS

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 9 / 19
© 2018 mCube Inc. All rights reserved.
Place the Accelerometer_MC3672 library folder to your
Arduino_sketch_folder/libraries/ folder.
You may need to create the library subfolder if it is your first library files. Then just restart
the IDE.
An excellent tutorial on Arduino library installation is located at:
http://learn.adafruit.com/adafruit-all-about-arduino-libraries-install-use
3.2 LOAD THE DEMO
Open File->Examples->MC3672-> MC3672demo and upload to your Arduino while it is wired
to the sensor.

MC3672 Accelerometer Driver Quick Start Guide and Demo
mCube Proprietary. APS-045-0017v1.2 10 / 19
© 2018 mCube Inc. All rights reserved.
Now open the serial terminal window at 115,200 baud rate speed to begin the test.
You will see the output from the serial terminal showing the current range scale and resolution
of the sensor in the first three lines followed by two lines of output sensor data at some output
data rate which depict “raw count" data for line 1: X: 6 Y: -2 Z: 1016 with 8G range, 14bit ADC
resolution. Line 2 indicates the SI units for measuring acceleration as X: 0.06 m/s^2 Y: -0.02
m/s^2 Z: 9.73 m/s^2.
This demo also includes the example for FIFO and Sniff interrupt mode. Those could be
enable by modify the definition below. These two examples must be run separately.
#define ENABLE_FIFO_WAKEUP 1
#define ENABLE_SNIFF_SHAKE_WAKEUP 0
Default input pin for interrupt is pin 8 and default FIFO threshold is 3 samples. FIFO size could
be set to maximum 32 samples or just enable FIFO to FIFO_FULL mode.
#define INTERRUPT_PIN 8
#define FIFO_SIZE 3
Indice
Altri manuali Mcube Unità di controllo
Manuali Unità di controllo popolari di altre marche

Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation
JS Automation MPC3034A Manuale utente

JAUDT
JAUDT SW GII 6406 Series Guida rapida

Spektrum
Spektrum Air Module System Manuale utente

BOC Edwards
BOC Edwards Q Series Manuale utente












