Megger MFT1500 Series Manuale utente

MFT1500 Series

Multifunction Tester

Quick Start Guide

GSAFETY WARNINGS

■Safety Warnings and Precautions must be read and understood

before the instrument is used. They must be observed during use.

■The circuit under test must be switched off, de-energised and

isolated before test connections are made when carrying out insulation

and continuity tests.

■Continuity of protective conductors and earthed equipotential bonding

of new or modified installations must be verified before carrying out

an earth fault loop impedance test, or RCD test.

■Circuit connections and exposed metalwork of an installation or

equipment under test must not be touched.

■The live circuit warning and Automatic discharge are additional safety

features and should not be regarded as a substitute for normal safe

working practices.

■Do not move the rotary switch positions while a test is in progress.

■The LCD ‘neon’ voltage indicators cannot reveal a Neutral - Earth

reversal. They cannot be relied upon to identify circuit correctness and

are for guidance only.

■After insulation tests, capacitive circuits must be allowed to discharge

before disconnecting test leads.

■The instrument should not be used if any part of it is damaged.

■Test leads, probes and crocodile clips must be in good order, clean

and with no broken or cracked insulation.

■Ensure that hands remain behind guards of probes/clips when testing.

■U.K. Safety Authorities recommend the use of fused test leads when

measuring voltage on high energy systems.

■Replacement fuses must be of the correct type and rating. Failure to fit

the correctly rated fuse will result in damage to the instrument in the

event of an overload. NOTE

THE INSTRUMENT MUST ONLY BE USED BY SUITABLY TRAINED AND

COMPETENT PERSONS

Users of this equipment and/or their employers are reminded that Health

and Safety Legislation requires them to carry out valid risk assessments of

all electrical work so as to identify potential sources of electrical danger

and risk of electrical injury such as inadvertent short circuits.

Where the assessments show that the risk is significant then the use of

fused test leads constructed in accordance with the HSE guidance note

GS38 'Electrical Test Equipment for use by Electricians' should be used.

Symbols used on the instrument are:

FCaution: risk of electric shock

GCaution: refer to accompanying notes

tEquipment protected throughout by Double Insulation (Class II)

cEquipment complies with current EU directives.

Equipment must not be connected to installations >500 V.

G>500V

Continuity Measurement [Ω]

Range switch set to [Ω] range

Test Lead options 1 or 2

The MFT1500 will automatically display continuity resistance

when connected.

Lead Null

Short test leads together and press the YELLOW test button on

the instrument or Switched Probe.

Continuity Buzzer ( Z)

The buzzer will sound automatically when a circuit is made

(default threshold <2 Ω)

Buzzer Threshold ( Z)

Select BUZZER range and press the ORANGE button until

required range is displayed.

Options, 2 Ω, 5 Ω, 10 Ω, 20 Ω, 50 Ω, and 100 Ω

Warning: Ensure the circuit to be tested is disconnected and

isolated before starting testing.

Voltage, Continuity and Insulation testing

Voltage measurement (V)

Range switch set to (V) range

The MFT1500 will automatically display circuit voltage up to

500 V a.c./d.c.

Backlight (MFT1502 only)

Intelligent mode - operates automatically. To switch to manual

mode, press the RED lock and the BLACK backlight buttons

together.

OPTION 2

Switched

probe

OPTION 1

2 wire lead

set

BLACK

BLACK (BACKLIGHT) YELLOW (TEST)

RED

(LOCK)

BLUE (0º - 180º) ORANGE (BUZZER)

BLACK

RED

PROBE

Insulation testing [MΩ]

Range switch set to [250 V, 500 V or 1 kV] range

Test Lead Options 1 or 2

For insulation voltage range select 250 V, 500 V or 1 kV as

required.

Press the YELLOW test button on the instrument or on the

switched probe to activate the test.

Insulation Test lock

Press the YELLOW test and RED lock buttons together to lock on

the insulation test mode.

The warning triangle is displayed during test lock.

To disable test lock press the YELLOW test button again.

Warning:

Hazardous voltages may be continuously present on the test

probes when the test button is locked down.

Non tripping loop test [NO TRIP]

Range switch set to the [NO TRIP]

Test Lead Options 1, 2 or 3

NOTE: A 3-Wire connection must be used.

Select when loop testing circuits with RCD protection fitted.

1) Firmly connect the GREEN lead to EARTH, the BLACK lead to

NEUTRAL and the RED lead to PHASE. (Alternatively insert

the plug into an installation socket) (OPTION 3).

2) Supply voltage and polarity are displayed.

3) The test will ‘beep’ and automatically start when a voltage is

detected.

4) Measured L-PE loop value is displayed.

The test can be repeated by pressing the YELLOW test button.

Warning: Live voltages present on test circuits during tests.

OPTION 1

2 wire

measurement

OPTION 2

Switched

Probe

OPTION 3

Mains plug

test lead

BLACK

GREEN GREEN

RED

PROBE

25 A (High current loop test) [25 A]

For use on circuits with NO RCD protection fitted.

Warning: The LCD 'Neons' are invalid when using the two wire

connection and should be ignored.

Range switch set to [25 A] range

Test Lead set: Options 1, 2 or 3

Phase-Earth loop impedance

1) Connect the GREEN lead to EARTH and the RED lead to

PHASE or plug into 13 Amp socket.

2) Supply voltage will be displayed.

3) The test will beep and automatically start when voltage is

detected.

4) Measured loop value is displayed.

5) To repeat, press the YELLOW test button.

Phase-Neutral loop impedance

Same connections to instrument as above but connect GREEN

lead to NEUTRAL and RED lead to PHASE.

Phase-Phase loop impedance

Same connections to instrument as above but connect the

GREEN lead to 2nd PHASE and the RED lead to 1st PHASE.

Bonded Metalwork Testing [25 A]

Test Lead set: OPTION 1 or 2

1) Connect the GREEN lead to the bonded metalwork.

2) Connect the RED lead to PHASE.

3) Supply voltage is displayed.

4) The test will ‘beep’ and automatically start when voltage is

detected.

5) Measured resistance value is displayed.

OPTION 3

Mains plug

test lead

OPTION 1

2 wire lead

set

OPTION 2

Switched

probe

GREEN

RED

GREEN

PROBE

PSC Measurement [PSC]

NOTE: High current 25 A measurement only!

Range switch set to [PSC]

Using test lead OPTION 1, 2 or 3 , connect the test leads as

follows:

Phase-Earth PSC

GREEN lead to EARTH and the RED lead to PHASE.

Phase-Neutral PSC

GREEN lead to NEUTRAL and RED lead to PHASE.

Phase-Phase PSC

GREEN lead to 2nd PHASE and the RED lead to 1st PHASE.

1) The supply voltage is displayed and the test will beep, and

automatically start when voltage is detected.

2) Measured PSC result is displayed.

RCD testing

1/2I, I and 5I RCD trip timing [RCD]

Warning: The LCD 'Neons' are invalid when using the two wire

connection and should be ignored.

Test Lead OPTION 1,2 or 3

Select 1/2I,Ior 5Ias required.

1) Ensure the right hand RCD range switch [mA] is set to the

correct range for the RCD under test.

2) Connect the test leads to the RCD as shown above.

3) Press the YELLOW test button on the instrument or the

switch probe.

On 1/2Ithe message >1999 ms is displayed after 2 seconds.

NOTE: The message ‘TrP’ will be displayed if the RCD trips

unexpectedly..

On Ithe trip time is displayed (or >200 ms if RCD fails to trip).

On 5Ithe trip time is displayed (or >40 ms if RCD fails to trip).

OPTION 3

Mains plug

test lead

OPTION 2

Switched

probe

OPTION 1

3 wire

measurement

BLACK

GREEN GREEN

RED PROBE

DC test [DC]

Used for testing DC Sensitive RCDs.

Test Lead OPTION 1,2 or 3 as required

1)Select the appropriate RCD rated current on the right hand

rotary switch.

2)Select the [DC] test on the left hand switch.

3) Press the YELLOW test button.

4)The trip time will be displayed .

5)If the RCD fails to trip, ">200 ms" will be displayed.

0º or 180º

On either the I, 5Ior DC test, to switch between 0º and 180º

press the BLUE 0°/180° button.

Ramp Test [ ]

Test Lead OPTION 1, 2 or 3 as required

A test current from 1/2Ito 1Iwill be applied during which the

RCD should trip.

1) Set the Range select to the RAMP symbol.

2) Set the RCD range switch [mA] to the current rating of the RCD.

3) Press the YELLOW test button.

4) Results are displayed in mA.

5) If RCD fails to trip the message ">***mA" is displayed.

*** = Final test current applied

Batteries

Uses 8 x 1.5 V AA (LR6) Alkaline dry cells.

Low battery voltage is indicated by the bsymbol in the display.

To replace batteries, disconnect test leads . Remove the battery

cover and carefully remove the battery carrier.

Replace with new batteries. Do not mix old and new batteries

Warning: OBSERVE CORRECT POLARITY . Incorrect battery

polarity could damage the instrument and invalidate the warranty.

Spare fuse

A blown fuse is indicated by the fsymbol. To replace the fuse:

Disconnect test lead and remove the battery cover, replace fuse

with spare provided: type: 500 mA (F) HBC 10 kA 500 V

This instrument is manufactured in the United Kingdom.

The company reserves the right to change the specification or design without prior

notice.

Megger is a registered trademark.

Part No 6172-812 - Edition 1 - Printed in England - 0503

Indice

Altri manuali Megger Apparecchiature di prova

Megger

Megger PVS 100i Manuale utente

Megger

Megger LT300 Manuale utente

Megger

Megger BMM500 Series Manuale utente

Megger

Megger MIT510/2 Manuale utente

Megger

Megger SWG 1750 C Manuale utente

Megger

Megger WM6 Manuale utente

Megger

Megger MFT70-US Manuale utente

Megger

Megger BITE 3 Manuale utente

Megger

Megger S1-552/2 Manuale utente

Megger

Megger BALTO Modular Manuale utente

Megger

Megger DET2/2 Manuale utente

Megger

Megger MIT200 Series Manuale utente

Megger

Megger MIT200 Series Manuale utente

Megger

Megger Programma Sverker 750 Manuale utente

Megger

Megger MIT300 Manuale utente

Megger

Megger BITE 2 Manuale utente

Megger

Megger S1-554/2 Manuale utente

Megger

Megger BM5200 Guida rapida

Megger

Megger MIT1020/2 Manuale utente

Megger

Megger RCDT300 Series Manuale utente

Megger

Megger T 99/1 Manuale utente

Megger

Megger ME1000351 Manuale utente

Megger

Megger BM100/4 Manuale utente

Megger

Megger PAT100 Series Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente