Metrologic MS7120 Orbit Manuale utente

METROLOGIC INSTRUMENTS, INC.

MS7120 Orbit®Presentation

Laser Scanner

Installation and User’s Guide

00-02408D_unit_7120_Cover_Oct_2005.qxd 10/26/2005 11:31 AM Page 1

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer,

who may quote brief passages in a review, or provided for in the Copyright

Act of 1976.

Products and brand names mentioned in this document are trademarks of

their respective companies.

TABLE OF CONTENTS

Introduction................................................................................................1

Scanner and Accessories..........................................................................2

Operational Notes .....................................................................................3

Installation

For RS232, OCIA and IBM 46XX Interfaces.........................................4

For Keyboard Wedge Interface.............................................................5

For Stand Alone Keyboard Interface.....................................................6

Notes for USB Interface ........................................................................7

Notes for MS7120-00 'Laser Emulation' ...............................................7

Scanner Parts............................................................................................8

Audible Indicators......................................................................................9

Visual Indicators ......................................................................................10

Failure Modes..........................................................................................11

Labels......................................................................................................12

Maintenance............................................................................................12

Scan Volume Specifications

Optimal Low Density (Default) ............................................................13

Optimal High Density ..........................................................................13

Close...................................................................................................14

Normal.................................................................................................14

Far.......................................................................................................15

Depth of Field by Minimum Bar Code Element Width

Optimal Low Density (Default) ............................................................16

Optimal High Density ..........................................................................17

Close...................................................................................................18

Normal.................................................................................................19

Far.......................................................................................................20

iii

TABLE OF CONTENTS

Installing the Optional Wall/Counter Mount .............................................21

Troubleshooting Guide ............................................................................22

RS-232 Demonstration Program .............................................................27

Applications and Protocols ......................................................................28

Design Specifications ..............................................................................29

Default Settings .......................................................................................31

Scanner and Cable Terminations............................................................36

Limited Warranty .....................................................................................39

Notices ....................................................................................................40

Patents ....................................................................................................44

Index........................................................................................................45

INTRODUCTION

Orbit®is an aggressive, omnidirectional laser bar code scanner.

Lightweight and rugged, Orbit is small in size, but BIG in performance.

Designed for applications where counter space is limited, Orbit is the

ideal presentation scanner for retail, convenience, liquor and specialty

stores. In addition, Orbit’s unique, contoured shape allows it to be

picked-up and used as a hand-held scanner when scanning large or

bulky items.

Engineered with a large, easy-to-find optimal scan area, Orbit increases

the first pass read rate for maximum productivity. The scanning head can

be tilted vertically a full 30° for added flexibility when scanning various

sized objects. These features increase the scanning throughput without

increasing the scanner size.

SCANNER INTERFACE

7120-00 Laser Emulation, RS-232 Transmit/Receive

7120-9 OCIA and RS-232 Transmit/Receive (Full RS232 Configurable)

7120-11 IBM 46XX and Full RS-232C

7120-41 Full RS-232C/Light Pen Emulation

7120-47 Keyboard Wedge, Stand-Alone Keyboard and RS-232

Transmit/Receive

7120-62 Ruby with Verifone, RS232

7120-67 Full RS-232C (OCIA Configurable)

Orbit offers a great deal of features to the consumer:

•Fully automatic scanning operation

•PowerLink compatible

•Data editing

•7 beeper tones

•Programmable depth of field

•Easy programming

SCANNER AND ACCESSORIES

BASIC KIT

Part # Description

MS7120 Orbit®Presentation Laser Scanner

00-02407 MetroSelect®Programming Guide

00-02408 MS7120 Installation and User’s Guide*

* Available on the Metrologic website - www.metrologic.com

OPTIONAL ACCESSORIES

Part # Description

AC to DC Power Transformer- Regulated 5.2VDC @ 650 mA output.

45-45593 120V United States

45-45591 220V-240V Continental European

45-45592 220V-240V United Kingdom

46-46803 220V-240V Australia

46-46983 220V-240V China

54-54xxx PowerLink Cable with built in power jack

Standard - 2.1m (7') straight cord, short strain relief

53-53xxx PowerLink Cable with built in power jack

Optional - 2.7m (9') coiled cord, long strain relief

xxx specifies connection to the host.

54-54002 Keyboard Wedge PowerLink Cable with Adapter Cable

54-54020 Stand Alone Keyboard PowerLink Cable

Other items may be ordered for the specific protocol being used. To order additional items,

contact the dealer, distributor or call Metrologic’s Customer Service Department at

1-800-ID-METRO or 1-800-436-3876.

SCANNER AND ACCESSORIES

OPTIONAL ACCESSORIES

Part # Description

MVC** Metrologic Voltage Converter Cable

+12VDC to +5.2VDC or -12VDC to +5.2VDC

MX009-2** MX009 USB Converter Cable

** Contact a Metrologic customer service representative for additional

information on the MVC and MX009 cable series and the host connections

available.

45-45619 Counter/Wall Mount Kit

Other items may be ordered for the specific protocol being used. To order

additional items, contact the dealer, distributor or call Metrologic’s Customer

Service Department at 1-800-ID-METRO or 1-800-436-3876.

OPERATIONAL NOTES

Metrologic recommends using the external power supply provided with the

scanner when operating the MS7120. When using power supplied by the host,

the host system should supply a minimum of 250 mA of current @ 5VDC.

Orbit is shipped from the factory programmed with default settings. To configure

the MS7120 scanner to meet the host system’s specific needs, refer to the

MetroSelect Programming Guide (MLPN 00-02407B) for instructions on how to

enter the program mode and select the appropriate bar codes.

INSTALLATION FOR RS232, OCIAAND IBM 46XX INTERFACES

1. Turn off the host system.

2. Plug the male 10-pin RJ45 end of

the PowerLink cable into the 10-pin

jack on the MS7120.

3. Connect the 9 pin female end of

the PowerLink cable to the host

device.

Note: Skip to #6 if receiving power

from the host system.

4. Plug the power supply’s L-shaped

plug into the power jack on the

PowerLink cable.

5. Check the AC input requirements

of the power supply to make sure

the voltage matches the AC outlet.

The outlet should be installed near

the equipment and be easily

accessible. Connect AC power to

the transformer.

6. Turn on the host system.

Note:

a. When the scanner first receives power, the green LED will turn

on. Then the scanner will beep once and the red LED will flash

simultaneously.

b. Plugging the scanner into the serial port of the PC does not

guarantee that scanned information will appear at the PC. A

software driver and correct configuration setting are also required

for proper communication to occur.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet the

requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

INSTALLATION FOR KEYBOARD WEDGE INTERFACE

1. Turn off the PC/Host.

2. Connect the male 10-pin RJ45 end of

the PowerLink cable to the jack on

the MS7120.

3. Connect the L-shaped plug of the

power supply into the power jack on

the PowerLink cable.

4. Make sure the AC input requirements

of the power supply matches the AC

outlet. Plug the power supply into the

AC outlet. The outlet should be near

the equipment and easily accessible.

5. Disconnect the keyboard from the PC.

Note the type of connector on the

keyboard and keyboard port on the PC.

6. The “Y” end of the PowerLink cable

terminates to female 5-pin DIN and

a male 6-pin mini DIN connector. If

necessary attach the supplied

adapter cable to the appropriate

end of the “Y” cable.

7. Connect one end of the “Y” cable to the Keyboard and other end of

the “Y” to the Keyboard port on the PC.

8. Power up the PC.

Manufacturer’s Recommendation:

Powering Orbit directly from the computer can sometimes cause

interference with the operation of the scanner or the computer. Not all

computers supply the same current through the keyboard port, explaining

why a scanner will work on one computer and not another. Metrologic

recommends using an external power supply. For additional information

contact a Metrologic customer service representative.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet the

requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

INSTALLATION FORSTANDALONE KEYBOARD INTERFACE

1. Turn off the host system.

2. Plug the male 10-pin RJ45 end of

the PowerLink cable into the

10-pin jack on the MS7120.

3. Connect the PowerLink cable to the

keyboard port on the host system.

4. Plug the power supply’s L-shaped

plug into the power jack on the

PowerLink cable.

5. Check the AC input requirements

of the power supply to make sure

the voltage matches the AC outlet.

The outlet should be installed near

the equipment and be easily

accessible. Connect AC power to

the transformer.

6. Turn on the host system.

Manufacturer’s Recommendation:

Powering Orbit directly from the computer can sometimes cause

interference with the operation of the scanner or the computer. Not all

computers supply the same current through the keyboard port, explaining

why a scanner will work on one computer and not another. Metrologic

recommends using an external power supply. For additional information

contact a Metrologic customer service representative.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet the

requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

Altri manuali per MS7120 Orbit

Indice

Altri manuali Metrologic Lettore di codici a barre

Metrologic

Metrologic MS6720 Manuale utente

Metrologic

Metrologic MS700i Manuale utente

Metrologic

Metrologic Stratos MS2xxx Series Istruzioni per l'installazione e il funzionamento

Metrologic

Metrologic MK1650-62B14 - Metrologic IS1650 - Wired Stationary Barcode... Manuale utente

Metrologic

Metrologic Cubit MS6520 Series Manuale utente

Metrologic

Metrologic Genesis MS7580 Manuale del proprietario

Metrologic

Metrologic Tire and Rubber Guida utente

Metrologic

Metrologic MS6200 Pulsar Series Manuale utente

Metrologic

Metrologic Hand-Held Scanner Manuale utente

Metrologic

Metrologic MS9590 VOYAGERGS series Manuale utente

Metrologic

Metrologic Stratos MS2x20 Series Istruzioni per l'installazione e il funzionamento

Metrologic

Metrologic MetroSelect Manuale utente

Metrologic

Metrologic Quantum T MS3580 Manuale utente

Metrologic

Metrologic IS4220 ScanGlove Manuale utente

Metrologic

Metrologic Stratos MS2420 Manuale utente

Metrologic

Metrologic MS 1690 Focus Series Manuale utente

Metrologic

Metrologic Fusion MS3780 Manuale utente

Metrologic

Metrologic IS3480 QuantumE Manuale utente

Metrologic

Metrologic MS9500 Voyager Series Manuale utente

Metrologic

Metrologic TECH 7 MS770 Manuale utente

Metrologic

Metrologic FocusE IS1650 Manuale utente

Metrologic

Metrologic 1070 Manuale utente

Metrologic

Metrologic MS2020 Stratos Manuale utente

Metrologic

Metrologic MS 1690 Focus Series Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente