METRON QA-IDS Guida alla risoluzione dei problemi

Q A - I D S

U s e r & S e r v i c e M a n u a l

Q A - I D S I n f u s i o n P u m p T e s t e r

METRON:

USA _ FRANCE NORWAY

1345 Mo roe NW, Suite 255A 30, rue Paul Claudel Travba eveie 1

Gra d Rapids, MI 49505 91000 Evry, Fra ce N-7044 Tro dheim, Norway

Pho e: (+1) 888 863-8766 Pho e: (+33) 1 6078 8899 Pho e: (+47) 7382 8500

Fax: (+1) 616 454-3350 Fax: (+33) 1 6078 6839 Fax: (+47) 7391 7009

E-mail: metronus@aol.com E-mail: metronfrance@infonie.fr E-mail: support@metron.no

Disclaimer

METRON provides this publicatio as is without warra ty of a y ki d, either express or implied, i cludi g

but ot limited to the implied warra ties of mercha tability or fit ess for a y particular purpose. Further,

METRON reserves the right to revise this publicatio a d to make cha ges from time to time to the co te t

hereof, without obligatio to METRON or its local represe tatives to otify a y perso of such revisio or

cha ges. Some jurisdictio s do ot allow disclaimers of expressed or implied warra ties i certai tra sactio s;

therefore, this stateme t may ot apply to you.

Limited Warranty

METRON warra ts that the QA-IDS I fusio Pump Tester will substa tially co form to published specifica-

tio s a d to the docume tatio , provided that it is used for the purpose for which it was desig ed. METRON will,

for a period of twelve (12) mo ths from date of purchase, replace or repair a y defective a alyzer, if the fault is

due to a ma ufacturi g defect. I o eve t will METRON or its local represe tatives be liable for direct, i di-

rect, special, i cide tal, or co seque tial damages arisi g out of the use of or i ability to use the QA-IDS I fu-

sio Pump Tester, eve if advised of the possibility of such damages. METRON or its local represe tatives are

ot respo sible for a y costs, loss of profits, loss of data, or claims by third parties due to use of, or i ability to

use the QA-IDS I fusio Pump Tester. Neither METRON or its local represe tatives will accept, or be bou d

by a y other form of guara tee co cer i g the QA-IDS I fusio Pump Tester other tha this guara tee. Some ju-

risdictio s do ot allow disclaimers of expressed or implied warra ties i certai tra sactio s; therefore, this

stateme t may ot apply to you.

Trademarks

IBM is a registered trademark, a d PC/XT is a trademark of IBM Corporatio . Ce tro ix is a registered trade-

mark of Ce tro ix Corporatio . Microsoft is a registered trademark a d Wi dows is a trademark of Microsoft

Corporatio .

Table of Contents

MANUAL REVISION RECORD............................................................................................5

1. INTRODUCTION..................................................................................................................7

1.1 QA-IDS Features .........................................................................................................................7

1.2 Specificatio s................................................................................................................................7

1.3 Ge eral I formatio ......................................................................................................................8

2. INSTALLATION...................................................................................................................9

2.1 Receipt, I spectio a d Retur .....................................................................................................9

2.2 Setup............................................................................................................................................10

2.3 Power ..........................................................................................................................................10

2.4 PRO-Soft QA-IDS.......................................................................................................................10

3. OPERATING QA-IDS........................................................................................................13

3.1 Co trol Switches a d Co ectio s.............................................................................................13

3.2 Key Pad Fu ctio s.....................................................................................................................14

3.3 Me u a d Fu ctio Keys............................................................................................................14

3.4 Display Me us a d Messages ...................................................................................................15

3.5 Pri ti g Test Reports.................................................................................................................20

3.6 Operator Mai te a ce................................................................................................................22

4. INFUSION PUMP TESTING.............................................................................................23

4.1 I troductio ................................................................................................................................23

4.2 Test Preparatio ..........................................................................................................................23

4.3 Occlusio Pressure/ Bolus Volume Testi g ..............................................................................25

4.4 I fusio Flow Rate a d Volume Testi g....................................................................................26

5. CONTROL AND CALI RATION....................................................................................29

5.1 Required Test Equipme t...........................................................................................................29

5.2 Adjusti g the Display Co trast ..................................................................................................29

5.3 Testi g Power Supply to IDS.....................................................................................................29

5.4 Testi g Pressure Gauge Accuracy..............................................................................................30

5.5 Testi g Flow Rate Accuracy.....................................................................................................30

5.6 Checki g the Battery Backup.....................................................................................................31

6. COMPONENT FUNCTIONS AND PARTS....................................................................33

6.1 Theory of Operatio ....................................................................................................................33

6.2 Power Supply..............................................................................................................................33

6.3 Pri ter Output..............................................................................................................................33

6.4 Serial Port...................................................................................................................................34

6.5 Microprocessor............................................................................................................................34

6.6 Pressure Gauge............................................................................................................................34

6.7 Pump............................................................................................................................................34

6.8 Stepper Motor/Drivers................................................................................................................34

6.9 Co trol Pa el...............................................................................................................................35

6.10 Compo e t Parts......................................................................................................................35

APPENDIX A: DIAGRAMS......................................................................................39

Processor board Compo e t Locatio ...........................................................................................41

6.10.1 Processor board Schematic Diagram 1 ...............................................................................42

6.10.2 Processor board Schematic Diagram 2 (Digital Part) .......................................................43

6.10.3 Processor board Schematic Diagram 3 (CPU) ..................................................................44

6.10.4 Processor board Schematic Diagram 4 (Memory) ............................................................45

6.10.5 Processor board Schematic Diagram 5 (RS232C a d Pri ter) .........................................46

6.10.6 Processor board Schematic Diagram 6 (Digital Outputs) .................................................47

6.10.7 Processor board Schematic Diagram 7 (Digital I puts) ....................................................48

6.10.8 Processor board Schematic Diagram 8 (A/D) ...................................................................49

6.10.9 Processor board Schematic Diagram 9 (Stepper Motor a d Drivers) ..............................50

6.10.10 Processor board Schematic Diagram 10 (Pressure Se sor a d Temperature) ................51

6.10.11 Processor board Schematic Diagram 11 (Mai Part) ......................................................58

6.10.12 Processor board Schematic Diagram 12 (Keyboard, Pressure Se sor a d Pump I dex)

..........................................................................................................................................................59

APPENDIX : ERROR REPORT FORM, QA-IDS.........................................................62

APPENDIX C: SUGGESTION FORM, QA-IDS...............................................................65

Manual Revision Record

This record page is for recordi g revisio s to your QA-IDS User and Service Manual that have

bee published by METRON or its authorized represe tatives. We recomme d that o ly the ma -

ageme t or facility represe tative authorized to process cha ges a d revisio s to publicatio s:

•make the pe cha ges or i sert the revised pages;

•e sure that obsolete pages are withdraw a d either disposed of immediately, or marked as

superseded a d placed i a superseded docume t file, a d;

•e ter the i formatio below reflecti g that the revisio s have bee e tered.

Rev No Date Entered Reason Signature of Person Entering Change

0 - Initial Release

This page intentionally left blank.

1. Introduction

This chapter describes the Metro ’s QA-IDS I fusio Pump Tester’s

features a d specificatio s.

1.1 QA-IDS Features

METRON’s QA-IDS I fusio Pump Tester is a precisio i stru-

me t, desig ed for use by trai ed service tech icia s, for testi g all

types of i fusio pumps accordi g to I ter atio al Electrotech ical

Commissio (IEC) Draft Sta dard 62.D (IEC 601.2.24). Tests i -

clude:

•volumetric tests

•bolus tests

•occlusio alarm tests

QA-IDS is capable of detecti g a mi imum volume variatio of o e

microliter i a ra ge of 0.10 milliliter per hour (ml/hr) to 1000.0

ml/hr. Flow measureme ts are take every 30 seco ds, so that the

measureme ts are i depe de t of the i fusio pump’s flow rate.

Test results, show i the QA-IDS's LCD display, ca be pri ted out

directly, or tra sferred to a PC via the PRO-Soft QA-IDS test auto-

matio software. PRO-Soft lets you desig test protocols, remotely

co trol the QA-IDS, a d store the test results.

1.2 Spe ifi ations

1. Flow Rate

Flow Range 0.10 ml/hr - 1000.0 ml/hr

Min. volume detection 0.72 µl

Dis lay resolution 0.01 ml/hr

2. Time Interval to A hieve ± % A ura y of Reading

1000 ml/hr 100 ml/hr 10 ml/hr

0.5% 0.6 sec 0.5% 6 sec 0.5% 52 sec

1.0% 0.3 sec 1.0% 3 sec 1.0% 26 sec

1.5% 0.2 sec 1.5% 2 sec 1.5% 18 sec

3. Pressure Generation

Range: - 200 to + 600 mmHg

Accuracy:

- 200 to + 200 mmHg: ± 10 mmHg

+ 201 to + 600 mmHg: ± 20 mmHg

4. O lusion Alarm Test

Measurement Range: - 400 to +1500 mmHg.

Accuracy:

- 400 to + 500 mmHg: ± 10 mmHg

+ 501 to + 1500 mmHg: ± 2% of reading

Maximum In ut Pressure: 2500 mmHg

5. Bolus Test

Accuracy: ± 20 µl

1.3 General Information

Temperature Requirements

+15°C to +35°C when o erating

0°C to +50°C in storage

Display

Ty e LCD gra hic dis lay

Al hanumeric format 4 lines, 40 characters

Dis lay control 7 function keys and a key ad

Data Input/ Output (2) Parallel rinter ort (1); Bi-directional RS

-232C (1) for Com uter control

Power From 110 VAC to 240 VAC, 47 / 63 Hz.

Me hani al Spe ifi ations

Housing Metal case

Height 13.5 cm / 5.31 in.

Width 23.5 cm / 9.25 in.

De th 24.5 cm / 9.65 in.

Weight 4.30 kg / 9.48 lbs.

Printer Port Centronics Interface

Standard A essories

User and Service Manual QA-IDS (P/N 15035)

Additional A essories

Carrying case (P/N 15100)

Carrying case, ext. rinter (P/N 10500)

PRO-Soft QA-IDS software (P/N 15200)

PRO-Soft QA-IDS DEMO (P/N 15201)

User Manual PRO-Soft QA-IDS (P/N 15205)

Storage

Store in the carrying case in dry surroundings within the tem era-

ture range s ecified. There are no other storage requirements.

Periodi Inspe tion

The unit should be calibrated every 12 months.

2. Installation

This chapter explai s u packi g, receipt i spectio a d claims, a d

the ge eral procedures for QA-IDS setup.

2.1 Re eipt, Inspe tion

and Return

1. I spect the outer box for damage.

2. Carefully u pack all items from the box a d check to see

that you have the followi g items:

•QA-IDS I fusio Pump Tester (P/N 15000)

•User a d Service Ma ual QA-IDS (P/N 15035)

3. If you ote physical damage, or if the u it fails to fu ctio

accordi g to specificatio , i form the supplier immedi-

ately. Whe METRON AS or the compa y’s represe ta-

tive, is i formed, measures will be take to either repair the

u it or dispatch a replaceme t. The customer will ot have

to wait for a claim to be i vestigated by the supplier. The

customer should place a ew purchase order to e sure de-

livery.

4. Whe retur i g a i strume t to METRON AS, or the

compa y represe tative, fill out the address label, describe

what is wro g with the i strume t, a d provide the model

a d serial umbers. If possible, use the origi al packagi g

material for retur shippi g. Otherwise, repack the u it us-

i g :

•a rei forced cardboard box, stro g e ough to carry the

weight of the u it.

•at least 5 cm of shock-absorbi g material arou d the u it.

•o abrasive dust-free material for the other parts.

Repack the u it i a ma er to e sure that it ca ot shift i the

box duri g shipme t.

METRON’s product warra ty is o page ii of this ma ual. The

warra ty does ot cover freight charges. C.O.D. will ot be ac-

cepted without authorizatio from METRON A.S or its represe -

tative.

2.2 Setup

1. Equipme t co ectio is as show i the typical setup be-

low.

2. If PRO-Soft QA-IDS is bei g used, attach a RS-232 ( ull

modem/data tra sfer co figured) cable to the 9-pi D-sub

outlet port located at the rear of the QA-IDS. Do ot attach

the pri ter cable to the QA-IDS. See below. However, if

you are ot usi g PRO-Soft QA-IDS, a d are se di g di-

rectly to a pri ter for pri touts, attach the pri ter cable to

the 25-pi outlet port .

2.3 Power

Main On/Off Switch. QA-IDS should remai off for at least 5 sec-

o ds before switchi g o agai , i order to allow the test circuits to

discharge fully.

2.4 PRO-Soft QA-IDS

PRO-Soft QA-IDS is a fro t-e d test automatio a d prese tatio

tool for METRON's QA-IDS I fusio Pump Tester. It allows you to

co duct the same tests, but by remote co trol via a IBM-com-

patilbe PC/XT with MS Wi dows (Versio 3.1 or later).

NOTE

Some RS-232C cables are

missing the connection be-

tween the seventh and the

eighth wires in the cable.

The cable may still be called

NULL-modem, but it will not

work with the QA-IDS. Refer

to the PRO-Soft QA-IDS

Users Manual for more in-

formation.

Indice

Altri manuali METRON Apparecchiature di prova

METRON

METRON QA-ST Guida alla risoluzione dei problemi

METRON

METRON QA-ST MKII Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente