Microchip Technology ATtiny104 Xplained Nano Manuale utente
ATtiny104 Xplained Nano
ATtiny104 Xplained Nano Evaluation Kit User's Guide
Preface
The Microchip ATtiny104 Xplained Nano Evaluation Kit is a hardware platform to evaluate the ATtiny104
microcontroller.
Supported by the Atmel Studio and MPLAB® X integrated development platform, the kit provides easy access to the
features of the Microchip ATtiny104 and explains how to integrate the device in a custom design.
The Xplained Nano MCU series evaluation kits include an on-board mini embedded programmer, and no external
tools are necessary to program the ATtiny104.
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 1
Table of Contents
Preface........................................................................................................................................................... 1
1. Introduction............................................................................................................................................. 3
1.1. Features....................................................................................................................................... 3
1.2. Kit Overview................................................................................................................................. 3
2. Getting Started........................................................................................................................................ 4
2.1. Xplained Nano Quick Start........................................................................................................... 4
2.2. Design Documentation and Relevant Links................................................................................. 4
3. Xplained Nano.........................................................................................................................................6
3.1. Mini Embedded Debugger............................................................................................................6
3.2. Power Sources............................................................................................................................. 6
3.3. Xplained Nano Standard Pinout................................................................................................... 7
3.4. Disconnecting mEDBG.................................................................................................................8
4. Hardware User Guide............................................................................................................................. 9
4.1. Connectors...................................................................................................................................9
4.2. Current Measurement.................................................................................................................. 9
4.3. Peripherals................................................................................................................................. 10
5. Embedded Debugger Implementation...................................................................................................11
5.1. Tiny Program Interface............................................................................................................... 11
5.2. Virtual COM Port.........................................................................................................................11
6. Hardware Revision History and Known Issues..................................................................................... 12
6.1. Identifying Product ID and Revision........................................................................................... 12
6.2. Fuse Masking............................................................................................................................. 12
6.3. Revision 2...................................................................................................................................12
6.4. Revision 1...................................................................................................................................12
7. Document Revision History...................................................................................................................13
The Microchip Website.................................................................................................................................14
Product Change Notification Service............................................................................................................14
Customer Support........................................................................................................................................ 14
Microchip Devices Code Protection Feature................................................................................................ 14
Legal Notice................................................................................................................................................. 14
Trademarks.................................................................................................................................................. 15
Quality Management System....................................................................................................................... 15
Worldwide Sales and Service.......................................................................................................................16
ATtiny104 Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 2
1. Introduction
1.1 Features
• ATtiny104 Microcontroller
• One Yellow User LED
• One Mechanical Button
• mEDBG
– Auto-ID for board identification in Atmel Studio/Microchip MPLAB® X IDE
– One green board status LED
– Programming
– Virtual COM port (CDC)
• USB Powered
1.2 Kit Overview
The Microchip ATtiny104 Xplained Nano Evaluation kit is a hardware platform to evaluate the ATtiny104.
Figure 1-1. ATtiny104 Xplained Nano Evaluation Kit Overview
RESET
TPI DATA
TPI CLK
NC
VREG
VUSB
GND
CLK OUT
CDC T X
CDC RX
VCC
PA0
PA1
PA2
PA3
PA4
PA5
GND
PB3
PB2
PB1
PB0
PA7
PA6
Micro USB Connector
User LED User button
mEDB G
ATtiny104
Power disconnect mEDB G disconnectStatus LED
TPI CLK
TPI DATA
RESET
USER L ED
USER BTN
CDC TX
CDC RX
Power
Ground
Clock
Serial
Target I/O
Shared I/Os
Program/Debug
ATtiny104 Xplained Nano
Introduction
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 3
2. Getting Started
2.1 Xplained Nano Quick Start
Steps to start exploring the Microchip Xplained Nano platform:
1. Download Atmel Studio/Microchip MPLAB® X IDE.
2. Launch Atmel Studio/Microchip MPLAB® X IDE.
3. Optional: Use Atmel START to generate drivers and examples.
4. Write your application code.
5. Connect a USB cable (Standard-A to Micro-B or Micro-AB) between the PC and the debug USB port on the
kit.
When the Xplained Nano kit is connected to your computer for the first time, the operating system will perform a
driver software installation. The driver file supports both 32- and 64-bit versions of Microsoft® Windows® XP,
Windows Vista®, Windows 7, Windows 8, and Windows 10. The drivers for the kit are included with Atmel Studio/
Microchip MPLAB® X IDE.
Once the Xplained Nano board is powered, the green status LED will blink and Atmel Studio/Microchip MPLAB® X
IDE will auto-detect which Xplained Nano board is connected. Atmel Studio/Microchip MPLAB® X IDE will present
relevant information like data sheets and kit documentation. The ATtiny104 device is programmed by the on-board
Mini Embedded Debugger and therefore, no external programmer tool is required.
2.2 Design Documentation and Relevant Links
The following list contains links to the most relevant documents and software for the ATtiny104 Xplained Nano.
•Xplained Products - Xplained Evaluation Kits are a series of easy-to-use evaluation kits for Microchip
microcontrollers and other Microchip products.
– Xplained Nano - used for low pin count devices and provides a minimalistic solution with access to all I/O
pins of the target microcontroller.
– Xplained Mini - used for medium pin count devices and adds Arduino Uno compatible header footprint and
a prototyping area.
– Xplained Pro - used for medium-to-high pin count devices that features advanced debugging and
standardized extensions for peripheral functions.
Note: All the above kits have on-board programmers/debuggers, which creates a set of low-cost boards for
evaluation and demonstration of features and capabilities of different Microchip products.
•Atmel Studio - Free IDE for the development of C/C++ and assembler code for microcontrollers.
•MPLAB® X IDE - MPLAB® X IDE is a software program that runs on a PC (Windows®, Mac OS®, Linux®) to
develop applications for Microchip microcontrollers and digital signal controllers. It is called an Integrated
Development Environment (IDE) because it provides a single integrated “environment” to develop code for
embedded microcontrollers.
•MPLAB® Code Configurator - MPLAB® Code Configurator (MCC) is a free software plug-in that provides a
graphical interface to configure peripherals and functions specific to your application.
•IAR Embedded Workbench® for AVR® - This is a commercial C/C++ compiler that is available for 8-bit AVR.
There is a 30-day evaluation version as well as a 4 KB code-size-limited kick-start version available from their
website.
•Atmel START - Atmel START is an online tool that helps the user to select and configure software components
and tailor your embedded application in a usable and optimized manner.
•Microchip Sample Store - Microchip sample store where you can order samples of devices.
•Data Visualizer - Data Visualizer is a program used for processing and visualizing data. The Data Visualizer
can receive data from various sources such as the EDBG Data Gateway Interface found on Curiosity Nano and
Xplained Pro boards and COM Ports.
ATtiny104 Xplained Nano
Getting Started
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 4
3. Xplained Nano
Xplained Nano is an evaluation platform that provides a set of small boards with access to all microcontroller I/O’s.
The platform consists of a series of low pin count Microcontroller (MCU) boards, which are integrated with Atmel
Studio/Microchip MPLAB® X IDE to present relevant user guides, application notes, data sheets, and example code
through Atmel Studio/Microchip MPLAB® X IDE. The platform also features a Virtual COM port for serial
communication to a host PC.
3.1 Mini Embedded Debugger
The ATtiny104 Xplained Nano contains the Mini Embedded Debugger (mEDBG) for on-board programming. The
mEDBG is a composite USB device of two interfaces: a debugger and a virtual COM port.
Together with Atmel Studio, the mEDBG debugger interface can program the ATtiny104. On ATtiny104 Xplained
Nano, the TPI interface is connected between the mEDBG and the ATtiny104.
The virtual COM port is connected to a UART on the ATtiny104 and provides an easy way to communicate with the
target application through the terminal software. It offers variable baud rate, parity, and Stop bit settings.
Note: The settings on the ATtiny104 must match the settings given in the terminal software.
Info: The virtual COM port in the mEDBG requires the terminal software to set the Data Terminal Ready
(DTR) signal to enable the UART pins connected to the ATtiny104. If the DTR signal is not enabled the
UART pins on the mEDBG are kept in high-z (tri-state), rendering the COM port unusable. The DTR signal
is automatically set by some terminal software, but it may have to be manually enabled in the target
terminal.
The mEDBG controls one status LED on the ATtiny104 Xplained Nano. The table below shows how the LED is
controlled in different operation modes.
Table 3-1. mEDBG LED Control
Operation Mode Status LED
Power-up LED is briefly lit
Normal operation LED is not lit
Programming Activity indicator; the LED flashes when programming/
debugging with the mEDBG
3.1.1 Xplained Nano Clock Output
The mEDBG outputs its CPU clock to the CLK pin 8, as shown in 3.3 Xplained Nano Standard Pinout. The clock
output can be used to feed the target device with a more accurate clock if this is needed for the application.
3.2 Power Sources
The kit can be powered by different sources. By default the kit will have a 5V supply and the voltage is taken directly
from the USB port through a 500 mA PTC fuse. The voltage from the USB connector can vary between 4.4V to 5.25V
(according to USB spec).
If other voltages are required, the kit must be disconnected from the USB to avoid damage or contention to the USB
power. The mEDBG must also be disconnected from the target section of the board. The board can be powered by
applying a voltage to one of the power connections on the board, according to the table below. To avoid any power
leakage through the mEDBG, this should also be disconnected by removing the resistors shown in Figure 3-3. For
placement of power connections, see 3.3 Xplained Nano Standard Pinout.
ATtiny104 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 6
Table 3-2. Power Connections
Power Connection Description
VUSB USB Voltage output when USB is connected (behind a PTC fuse). Can be used as power
input when USB is not used.
VREG Regulated voltage from VUSB. If the kit does not have a regulator, this is directly connected
to VUSB.
VCC Target voltage supply. By default, connected to VREG through a 0Ω resistor. Apply external
voltage here if the resistor is removed.
Figure 3-1. Power Supply Block Diagram
USB Target MCUPTC
Power source
Power connection
Power consumer
0-ohm Resistor
VUSB /
VREG VCC
mEDBG
3.3 Xplained Nano Standard Pinout
Xplained Nano kits have a standard pinout in the mEDBG section, as shown in the tables and figure below. The
program/debug pins will change depending on the target interface but will remain at the same locations.
Xplained Nano kits have a target section where all I/O pins will be available and fanned out. Except for the VCC and
GND pins with fixed positions, there are no defined pin functions in this area. The first pin in the target area is the
VCC pin, located right next to the VREG pin of the standard section. The last pin is GND, and it is located next to the
CDC RX pin in the standard section. For reference, see the figure below.
3.3.1 Standard Pinout for TPI
Table 3-3. Xplained Nano Standard Pinout for TPI
Pin Number Name Description
1 RST Reset line
2 TPID TPI Program data line
3 TPIC TPI Program clock output
4 NC No Connect
5 VREG Regulated voltage or VUSB if no regulator present
6 UART RX mEDBG UART RX line
7 UART TX mEDBG UART TX line
8 CLK mEDBG clock output
9 GND Ground
10 VUSB USB voltage
ATtiny104 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 7
Figure 3-2. Xplained Nano Standard Pinout for TPI
RESET
TPI DATA
TPI CLK
NC
VREG
VUSB
GND
CLK OUT
CDC TX
CDC RX
VCC GND
Micro USB ConnectormEDBGPower disconnect Status LED
3.4 Disconnecting mEDBG
The target device can be completely separated from the mEDBG, but this requires some small modifications to the
board using a soldering iron. By removing the resistors in the sections shown in the figure below, the mEDBG is
completely disconnected from the target controller. If desired to connect the mEDBG again, solder in 0Ω resistors or
solder in 100-mil headers on the header footprints and use wire-straps to connect the interfaces.
Figure 3-3. Kit Modifications
Power disconnect mEDBG disconnect
ATtiny104 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 8
4. Hardware User Guide
4.1 Connectors
4.1.1 ATtiny104 Xplained Nano Pinout
The ATtiny104 Xplained Nano has a direct fan-out of the I/O pins of the device and all I/O’s are accessible at the
edge connectors.
Table 4-1. Edge Connector
Edge
Connector
ATtiny104 Pin Functions Shared Functionality
1 VCC Power supply
2 PA[0] PCINT0/ADC0/AIN0/T0/CLKI/TPICLK mEDBG TPI Clock
3 PA[1] PCINT1/ADC1/AIN1/OC0B/TPIDATA mEDBG TPI Data
4 PA[2] PCINT2/RESET mEDBG Reset
5 PA[3] PCINT3/OC0A
6 PA[4] PCINT4/ICP0
7 PA[5] PCINT5/ADC2/OC0B User LED
8 PA[6] PCINT6/ADC3
9 PA[7] PCINT7
10 PB[0] PCINT8/ADC4
11 PB[1] PCINT9/INT0/ADC5/XCK0/OC0A/CLKO User button
12 PB[2] PCINT10/ADC6/TxD0/ICP0 mEDBG CDC RX
13 PB[3] PCINT11/ADC7/ACO/RxD0/T0 mEDBG CDC TX
14 GND Ground
4.2 Current Measurement
The power to the target controller ATtiny104 is connected from the VREG supply to the targets VCC supply with a 0Ω
resistor, as shown in the figure below. To measure the power consumption of the device, remove the 0Ω resistor and
replace it with an ammeter. The ammeter can be connected between the VREG and VCC pads for easy
measurement.
Tip: To connect the two power domains again, solder in a 0Ω resistor on the footprint or a 100-mil header
on the header footprint at the edge of the board and place a jumper between VREG and VCC.
ATtiny104 Xplained Nano
Hardware User Guide
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 9
CAUTION
Removing the resistor while the kit is powered without an ammeter or jumper may cause the ATtiny104 to
be powered through its I/O pins. This may cause permanent damage to the device.
Figure 4-1. Current Measurement
VREG
VCC
Power disconnect
4.3 Peripherals
4.3.1 LED
There is one yellow LED available on the ATtiny104 Xplained Nano board that can be turned ON and OFF. The LED
can be activated by driving the connected I/O line to GND.
Table 4-2. LED Connection
ATtiny104 Pin Function Shared Functionality
PA5 Yellow LED0 Edge connector
4.3.2 Mechanical Buttons
ATtiny104 Xplained Nano contains one mechanical button. This is a generic user configurable button and when a
button is pressed it will drive the I/O line to GND.
Info: There is no pull-up resistor connected to the generic user button. Remember to enable the internal
pull-up in the ATtiny104 to use the button.
Table 4-3. Mechanical Button
ATtiny104 Pin Description Shared Functionality
PB1 User button Edge connector
ATtiny104 Xplained Nano
Hardware User Guide
© 2019 Microchip Technology Inc. User Guide DS40002160A-page 10
Indice
Altri manuali Microchip Technology Scheda madre
Microchip Technology
Microchip Technology HV9805 Manuale utente
Microchip Technology
Microchip Technology TC1303 DFN Manuale utente
Microchip Technology
Microchip Technology MCP1664 Manuale utente
Microchip Technology
Microchip Technology MPLAB ICE Manuale utente
Microchip Technology
Microchip Technology EVB-USB3503 QFN Manuale utente
Microchip Technology
Microchip Technology MCP16301 Manuale utente
Microchip Technology
Microchip Technology MCP3903 Manuale utente
Microchip Technology
Microchip Technology dsPICDEM MCHV Manuale utente
Microchip Technology
Microchip Technology XLP Manuale utente
Microchip Technology
Microchip Technology Microsemi PolarFire MPF300T Manuale utente
Microchip Technology
Microchip Technology UCS1003-1 Manuale utente
Microchip Technology
Microchip Technology dsPICDEM 1.1 Manuale utente
Microchip Technology
Microchip Technology dsPICDEM MCHV-3 Manuale utente
Microchip Technology
Microchip Technology AVR-BLE Manuale di installazione
Microchip Technology
Microchip Technology dm164136 Manuale utente
Microchip Technology
Microchip Technology ATtiny1607 Curiosity Nano Manuale utente
Microchip Technology
Microchip Technology SAMA5D3 XPLAINED Manuale utente
Microchip Technology
Microchip Technology Explorer 16 Manuale utente
Microchip Technology
Microchip Technology MCP1663 Manuale utente
Microchip Technology
Microchip Technology Curiosity Nano Series Manuale di installazione
Microchip Technology
Microchip Technology ATtiny3217 Xplained Pro Manuale utente
Microchip Technology
Microchip Technology Hello FPGA Manuale utente
Microchip Technology
Microchip Technology Curiosity High Pin Count Manuale utente
Microchip Technology
Microchip Technology PIC16F15376 Curiosity Nano Manuale di installazione
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
