Microchip Technology PICDEM Manuale utente

PICDEM™ Mechatronics Demo Board

Quick Start Guide

The PICDEM Mechatronics Demo Board is programmed at the factory with a demonstration program. The board must

be conﬁgured as described in this chapter in order to use the demonstration program. Once the board is conﬁgured

and powered up, the speed of the Brushed DC (BDC) motor on the board may be varied using the potentiometer

(POT1). The 8-bit hexadecimal interpretation of the position of POT1 is displayed on the LCD.

Board Setup

Using the provided wire jumpers, screwdriver and shunts (2-pin black hard plastic jumpers), conﬁgure the

board as shown in the Quick Board Setup Schematic.

1. Attach the leads of the brushed DC motor to Drive 1 and Drive 2 using the screwdriver.

2. Connect POT1 (on J4) to C1- (on J13) using a wire jumper.

3. Connect P1 (on J1) to RD7 (on J10) using a wire jumper.

4. Connect N2 (on J1) to RD2/CCP2 (on J10) using a wire jumper.

5. Connect +5 VDC to the center pin on JP8 using a shunt.

Board Power-Up

Supply power to the board in one of the following ways:

• Connect a 9-12 VDC (0.75 amp minimum) supply using J9 (see note below)

• Connect a 9-12 VDC (0.75 amp minimum) supply to the P21 and P20 screw terminals.

• Connect a 9 VDC battery to the battery connector.

• Connect a 5 VDC (1.2 amp minimum) supply to TP2 and TP3.

Demonstration Program

Press CLR FAULT (SW5), which is near the bottom right corner of the board. Turn POT1 clockwise to

increase the speed of the motor. Note that the number displayed on the LCD increases as you turn the

potentiometer clockwise.

Try experimenting with the other sensors on the board:

• Move the jumper wire on POT1 (J4) to Light (J4). Vary the intensity of light shining on the light sensor

located near the top left corner of the board. Notice what happens to the motor.

• Move the same jumper wire to TEMP (J4). Blow on the temperature sensor located on the top left corner

of the board. Note what happens to the number displayed on the LCD.

• Move the jumper wire back to POT1. Move the jumper wire from N2 (J1) to D0 (J14). Watch what

happens to the intensity of LED D0 as you turn the potentiometer.

Microchip Technology Inc. •2355 W. Chandler Blvd. •Chandler, AZ 85224-6199 USA •(480) 792-7200 •FAX (480) 792-7277

The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. In-Circuit Serial

Programming, ICSP and PICDEM are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of

DS51562B *DS51562B*

Quick Board Setup Schematic

Indice

Altri manuali Microchip Technology Scheda madre

Microchip Technology

Microchip Technology BM62 Manuale utente

Microchip Technology

Microchip Technology dsPICDEM MCHV Manuale utente

Microchip Technology

Microchip Technology MCP2150 Manuale utente

Microchip Technology

Microchip Technology EVB-USB7206 Manuale utente

Microchip Technology

Microchip Technology EVB-KSZ8563 Manuale utente

Microchip Technology

Microchip Technology Curiosity Nano Series Manuale di installazione

Microchip Technology

Microchip Technology PAC1921 Manuale utente

Microchip Technology

Microchip Technology SAM R34 Xplained Pro Manuale utente

Microchip Technology

Microchip Technology RN-2483-PICtail Manuale utente

Microchip Technology

Microchip Technology ADM00612 Manuale utente

Microchip Technology

Microchip Technology MCP1663 Manuale utente

Microchip Technology

Microchip Technology UCS1003-1 Manuale utente

Microchip Technology

Microchip Technology ATtiny3217 Curiosity Nano Manuale di installazione

Microchip Technology

Microchip Technology MCP651 Manuale utente

Microchip Technology

Microchip Technology PICDEM 2 Plus Manuale utente

Microchip Technology

Microchip Technology OS81210 Manuale utente

Microchip Technology

Microchip Technology dsPICDEM MCSM Manuale utente

Microchip Technology

Microchip Technology HV2916 Manuale utente

Microchip Technology

Microchip Technology SAM-IoT Wx v2 Manuale di installazione

Microchip Technology

Microchip Technology SAMA5D3 XPLAINED Manuale utente

Microchip Technology

Microchip Technology AVR-IoT WA Manuale utente

Microchip Technology

Microchip Technology PIC16F17146 CNANO Manuale di installazione

Microchip Technology

Microchip Technology EVB-LAN9252-HBI+ Manuale utente

Microchip Technology

Microchip Technology dsPICDEM 1.1 Plus Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente