Microtek 815C Manuale utente
USER'S MANUAL
www.microtek.com
HIGH RESOLUTION WITH SUPER- WIDE VIEWING ANGLE
18"
i
Table of Contents
Safety Declaration
FCC Compliance Statement iii
Radio Frequency Interference Statement iv
CanadianDOCNotice v
Chapter 1
Introduction 1
Precautions 1
Product Features 1
Unpacking 2
Specifications 3
Supported Timing 4
Cleaning 5
Chapter 2
InstallingtheMonitoe 6
Connecting the Monitor 7
Adjusting the Viewing Angle 8
Chapter 3
OperatingtheMonitor 9
How to Use the OSD 10
Structure of OSD Menus 10
Operating Procedure 10
ii
MenuTable 11
Troubleshooting Procedures 13
ForYourSafety 15
iii
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet different from that to which
the receiver is connected.
iv
•Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use
the shielded signal cord supplied with this unit.
The Federal Communications Commission warns that changes or
modifications of the unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
CE mark for Class B ITE (Following European standard
EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998,
EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
v
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la class B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.”
ENERGY STAR
This product meets the Energy Star guidelines for energy efficiency.
TCO’99
Congratulations! You have just purchased a TCO’99 approved and labeled
products. Your choice has provided you with a product developed for
professional use. Your purchase has also contributed to reducing the
burden on the environment and also to the further development of
environmentally adapted electronics products.
1
Chapter 1
Introduction
Precautions
zRead all of these warnings and save the manual for later use.
zFollow all warning and instructions on the product.
zDo not cover or block the vent holes in the case.
zDo not insert sharp objects or spill liquid into the LCD monitor through the
cabinet slots; this may cause accidental fire, electric shock or failure.
zDisconnect the power plug from the AC outlet if you will not use it for an
extended period of time.
zDo not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks.
zDo not touch the screen directly with your fingers you may damage the screen,
and oil from your skin is difficult to remove.
zDo not apply pressure to screen, as the screen is very delicate.
zKeep the monitor away from extreme heat, cold or humid places.
zDo not place the monitor directly under sunlight, dusty surroundings, or near
equipment, which may generate strong magnetic fields.
Product Features
zSupport SXGA resolution of 1280x1024 pixels
zWide viewing angle
zWide tilting angle
zVESA DPMS-compliant power saving: automatically powers down the
monitor after a defined period of inactivity
zDigital Character Smoothing
zAutomatic Set-Up
zErgonomic Design: TCO Approved
zWindows 95/98/2000/XP Plug & Play Compliant
zVersatile, functional & User friendly OSD
zPlug & Play: Conform to the VESA standards and support DDC1/2B spec.
2
Unpacking
Before unpacking your LCD Monitor, prepare a stable, level, and clean surface near a
wall outlet for your LCD Monitor.
1. Set the LCD Monitor box in an upright position and open from the top of the
box before removing the right/left cushions.
2. Remove the back cover from your monitor (pull from the bottom of cover to
open) to install your PC system.
Accessories
1 pc 1 pc 1 pc 1 pc 1 pc 1 pc
VGA Cable AC/DC Adaptor Power Cord Audio Cable User’s Manual DVI Cable
(Dual Model)
Remember to save your original box and packaging material in case you
need to transport or ship the monitor.
3
Specifications
LCD type 18” SXGA Color TFT
Display Area 14.1 x 11.2 in. (357.1 x 285.7 mm)
Input signal Analog (0.7Vp-p/75 ohm positive)
Dot pitch 0.28mm
Scanning frequency (H) 31.5~79.97 KHz, (V) 56.3~75.02 Hz
Resolution 1280 x 1024
Display color 16.7M colors
Luminance 250 cd/m2
Contrast ratio 350:1
Response time 30 ms(Typ.)
Viewing angle (H) 160°/ (V) 160°
Control type OSD
Plug & Play VESA DDC 1/2B
Dimension (H x W x D) 17.6 x 16.7 x 7.3 in.( 447 x 424.2 x 185.4 mm)
Weight 12.9 lbs (5.86Kg)
Tilt -3 ~ 20 degrees (Upward)
Wall mount 75mm x 75mm (VESA Standard, Optional)
AC input AC 100V ~ 240V , 50/60Hz
Power management VESA DPMS
Power Consumption 50W Max (on)/5W (Power Saving off mode)
Regulatory compliance UL, FCC Class B, EPA Energy Star
4
Supported Timing
Analog
Display Mode Horizontal
Frequency Vertical
Frequency
31.5 KHz 60 Hz
640 x 480
37.5 KHz 75 Hz
VGA
720 x 400 31.5 KHz 70.1 Hz
35.2 KHz 56.3 Hz
37.9 KHz 60.3 Hz
46.9 KHz 75.0 Hz
SVGA 800 x 600
48.1 KHz 72.0 Hz
48.4 KHz 60.0 Hz
56.5 KHz 70.1 Hz
XGA 1024 x 768
60.0 KHz 75.0 Hz
63.98 KHz 60.02 Hz
VESA
SXGA 1280 x 1024
79.97 KHz 75.02 Hz
640 x 480 35.0 KHz 66.7 Hz
Macintosh VGA
832 x 624 49.7 KHz 74.6 Hz
MS-DOS 640 x 350 31.5 KHz 70.1 Hz
Indice
Altri manuali Microtek Monitor
Microtek
Microtek 201SD Manuale utente
Microtek
Microtek C580 Manuale utente
Microtek
Microtek 714M Manuale utente
Microtek
Microtek C788 Manuale utente
Microtek
Microtek C783 Manuale utente
Microtek
Microtek 525M Manuale utente
Microtek
Microtek C786 Manuale utente
Microtek
Microtek JTX V7s Manuale utente
Microtek
Microtek 722S Manuale utente
Microtek
Microtek C593 Manuale utente
Microtek
Microtek C893 Manuale utente
Microtek
Microtek C997SD Manuale utente
Microtek
Microtek C593 Manuale utente
Microtek
Microtek 515M Manuale utente
Microtek
Microtek 211SD Manuale utente
Microtek
Microtek JTX V5 Manuale utente
Microtek
Microtek C588 Manuale utente
Microtek
Microtek C586P Manuale utente
Microtek
Microtek 527C Manuale utente
Microtek
Microtek 512M Manuale utente
