MiLAN MIL-S8000G Manuale utente

8-Port Gigabit Switch

MIL-S8000G

User Guide

Eight Auto-negotiation 10/100/1000Mbps Gigabit Ethernet

RJ-45 Ports. Each port with Auto MDI/MDIX.

Regulatory Approval

- FCC Class A

- UL 1950

- CSA C22.2 Number 950

- EN60950

- CE

EN55022 Class A

EN55024

Canadian EMI Notice

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel

brouilleur du Canada.

European Notice

Products with the CE marking comply with both the EMC Directive (89/336EEC) and the Low Voltage

Directive (73/23EEC) issued by the commisions of the European Community. Compliance with these

directives implies conformity to the following European norms:

- EN55022 (CISPR 22) - Radio Frequency Interference

- EN61000-X - Electromagnetic Immunity

- EN60950 (IEC950) - Product Safety

Five-Year Limited Warranty

MiLAN Technology warrants to the original consumer or purchaser that each of its product and component thereof,

will be free from defects in material and/or workmanship for a period of five years from the original factory shipment

date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable.

MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of

merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall

MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in

connection with the performance of the product delivered hereunder. MiLAN Technology will in no case cover

damages arising out of the product being used in a negligent fashion or manner.

Trademarks

trademarks of MiLAN Technology in the United States and/or other countries.

To Contact MiLAN Technology

For prompt response when calling for service information, have the following information ready:

- Product serial number and revision

- Date of purchase

- Vendor or place of purchase

You can reach MiLAN Technology technical support at:

- E-mail: support@milan.com

- Telephone: +1.408.744.2751

- Fax: +1.408.744.2771

MiLAN Technology

1329 Moffett Park Drive

Sunnyvale, CA 94089

United States of America

Telephone: +1.408.744.2775

Fax: +1.408.744.2793

http://www.milan.com

[email protected]

P/N 90000404_A

Table of Contents

1. Introduction

Features

Package Contents

2. Hardware Description

Front Panel

LED Indicators

Rear Panel

3. Installation

Desktop Installation

Rack-mount Installation

Power On

4. Network Application

Backbone Switch

5. Network Configuration

5.1 Port Status

5.2 Port Configuration

5.3 Mirror Configuration

5.4 VLAN Configuration

5.5 VLAN Setup

5.6 Trunk Configuration

5.7 Miscellaneous Configuration

6. Troubleshooting

7. MIL-S8000G Technical Specifications

1. Introduction

Gigabit Ethernet over copper technology is a cost-effective way for

network equipment to be upgraded from Fast Ethernet to Gigabit speeds

without the use of expensive fiber optics cabling. Gigabit networks create

high-speed backbone connections between switches, servers, databases

and end stations.

The MIL-S8000G, an 8-Port Gigabit switch, is an ideal solution for solving

traffic block at the core of the network. It offers eight auto-negotiation

10/100/1000Base-T Gigabit Ethernet ports that can significantly improve

your network’s backbone performance. The switch will fit into any level

network to act as an exit to the backbone switch that can handle

throughput speeds up to 2000Mbps at Full-duplex mode.

Figure 1-1. MIL-S8000G

The switch will automatically detect the speed of the device that you plug

into it to allow connections to 10, 100 or 1000Mbps devices.

The eight port Gigabit switch features automatic MDI/MDIX connections

for each port. It also features store-and-forward switching and auto-

learning of source addresses with an 8,000 entry MAC address table.

Features

Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards

Eight auto-negotiation 10/100/1000Base-TX switch ports (Using

shielded RJ-45 connections)

Automatic MDI/MDIX crossover for all ports

Embedded 8K entry MAC address table (Supports 8K

Unicast/Multicast/Broadcast addresses)

Store-and-Forward architecture

Full Duplex and Half Duplex flow control support

Plug-and-Play configuration

LED Indicators for Power, 100M, 1000M, LK/ACT, and FDX/COL

Standard 19-inch rackmount design

Console Management (Port Configuration/Statistics, Port Mirroring,

Port-Based VLAN’s and Port Trunking)

Package Contents

MIL-S8000G 8 port Gigabit switch

Power Cord

Four Adhesive Rubber Feet

User’s Manual

Warranty Card

Compare the contents of your MIL-S8000G package with the

standard checklist above. If any item is missing or damaged, please

contact your local dealer for service.

2. Hardware Description

Front Panel

The Front Panel of the 8-Port Gigabit Switch consists of eight auto-

negotiation 10/100/1000Mbps Ethernet RJ-45 connectors, supporting

automatic MDI/MDIX, and four LED-indicators (1000M, 100M, LK/ACT,

FUL/COL) for each Gigabit port.

Figure 2-1. The Front Panel of the 8-Port Gigabit Switch

RJ-45 Ports ( Auto MDI/MDIX ): Eight auto-negotiation

10/100/1000Mbps Ethernet RJ-45 connectors.

Console Port : Console management is available through the

Console Port. A direct connection between the Switch and an end

station ( PC ) via a RS-232 cable is required.

LED Indicators

The LED Indicators gives a real-time indication of system operating

statuses. There are four LED-indicators for each Gigabit port and one

Power LED for Unit. The following table provides descriptions of LEDs

status and their meaning.

Figure 2-2.

LED Indicators.

Console Port

LEDs

RJ-45 Gigabit Ports

LED Status Description

Green Power On

Power

Off Power is not connected

Green The port is operating at the speed of 1000Mbps.

1000M

Off No device attached or in 10/100Mbps mode

Green The port is operating at the speed of 100Mbps.

100M

Off No device attached or in 10Mbps mode

Green The port is connecting with the device.

Blinks The port is receiving or transmitting data.LK/ACT

Off No device attached.

Yellow The port is operating in Full Duplex mode.

Off No device attached or in Half Duplex mode.

Table 2-1. Descriptions of LED Indicators

Rear Panel

The 3-pronged power plug and ventilation fan are located at the rear

panel. The switch will work with AC in the range 100-240V AC, 50-60Hz.

The rear panel of the MIL-S8000G Gigabit switch is shown below.

Figure 2-3. The Rear Panel of the MIL-S8000G Switch

3. Installation

Desktop Installation

Set the switch on a sufficiently large flat space with a power outlet nearby.

The surface should be clean, smooth, level, and sturdy.

Make sure there is enough clearance around the switch to allow

attachment of cables, power cord and air circulation.

Attaching Rubber Feet

A. Make sure mounting surface on the bottom of the switch is grease

and dust free.

B. Remove adhesive backing from the rubber feet.

Figure 3-1. Attaching rubber feet to each corner on the bottom of the

Switch

C. Apply the rubber feet to each corner on the bottom of the switch.

These footpads can prevent the switch from shock/vibration.

Rack-mounted Installation

The MIL-S8000G includes a rack-mounted kit that allows it to be mounted

in an EIA standard size, 19-inch Rack.

Perform the following steps to rack mount the switch:

A. Position one bracket to align with the holes on one side of the switch

and secure it with the smaller bracket screws. Then attach the

remaining bracket to the other side of the switch.

Figure 3-2. Attach mounting brackets with screws

B. After attaching both mounting brackets, position the MIL-S8000G

switch in the rack by lining up the holes in the brackets with the

appropriate holes on the rack. Secure the switch to the rack with a

screwdriver and the rack-mounting screws.

Figure 3-3. Mounting the MIL-S8000G in an EIA standard 19-inch Rack

Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance

on the front and 3.4 inches (8 cm) on the back of the switch. This is

especially important for enclosed rack installation.

Power On

Connect the power cord to the power socket on the rear panel of the

switch. The other side of power cord connects to the power outlet. The

internal power supply in the Switch works with AC in the voltage range

100-240VAC, frequency 50~60Hz.

Check the power indicator on the front panel to see if power is properly

supplied.

4. Network Application

The MIL-S8000G Switch can be used connect servers, switches,

workstations, and PCs (a Gigabit 1000Base-T NIC is required for PC

installation) to each other by connecting these devices directly to the

Switch. The Switch automatically learns node addresses, which are used

to filter and forward all traffic, based on the destination address.

Backbone Switch

The MIL-S8000G Switch is an ideal solution for enterprise networks

where large data broadcasts are constantly processed.

All ports can be connected to departmental switches, and the

departmental switches can be connected to the MIL-S8000G Switch.

Each end station can access the server’s data by connecting the servers

to the core switch. This will allow all the devices in the network to

communicate with each other.

Indice

Altri manuali MiLAN Interruttore

MiLAN

MiLAN MIL-S24002TGXX Manuale utente

MiLAN

MiLAN MIL-SM802GAF Manuale utente

MiLAN

MiLAN MIL-S800I Manuale utente

MiLAN

MiLAN MIL-SME801P Manuale di istruzioni

MiLAN

MiLAN MIL-SM800P Manuale utente

MiLAN

MiLAN MIL-S800 Manuale utente

MiLAN

MiLAN mil-s2400s Manuale utente

MiLAN

MiLAN MIL-SM24004TG Manuale utente

MiLAN

MiLAN MIL-SM8TAF1GPA Manuale di programmazione

MiLAN

MiLAN MIL-S501MT-15 Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

MiLAN

MiLAN MIL-SM800 Manuale utente

MiLAN

MiLAN MIL-S1600S Manuale utente

MiLAN

MiLAN MIL-S5000T Manuale utente

MiLAN

MiLAN MIL-SM2401MAF Manuale utente

MiLAN

MiLAN MIL-SM808G Manuale utente

MiLAN

MiLAN TR-TP-HB-1600 Manuale utente

MiLAN

MiLAN MIL-S2612 Manuale utente

MiLAN

MiLAN MIL-S500 Manuale utente

MiLAN

MiLAN MIL-S8000T Manuale utente

MiLAN

MiLAN MIL-SM4804G Manuale utente

MiLAN

MiLAN MIL-S24T2GPA Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale di istruzioni

MiLAN

MiLAN MIL-SM801P Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuale utente