Mitsubishi Electric P95DW-DC Manuale utente
FRANÇAIS DEUTSCHITALIANO
NEDERLANDS
ESPAÑOL ENGLISH
DIGITAL MONOCHROME PRINTER
MODEL
P95DW-DC
OPERATION MANUAL
THIS OPERATION MANUAL IS IMPORTANT
TO YOU.
PLEASE READ IT BEFORE USING YOUR
DIGITAL MONOCHROME PRINTER.
DIGITAL MONOCHROME
PRINTER
FRANÇAIS DEUTSCHITALIANO
NEDERLANDS
ESPAÑOL ENGLISH
CAUTION:
Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his or her own expense.
Information:
This class A digital apparatus complies with Canadian ICES-003.
"CLASSIFIED BY UNDERWRITERS LABORATORIES INC.®
WITH RESPECT TO ELECTRICAL SHOCK, FIRE AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH ANSI/AAMI ES60601-1 (2005, 3rd ed.) AND CAN/CSA-C22.2
No. 60601-1 (2008)"
Indications according to IEC60601-1
1. Functions and intended usage of this product
This product receives signals from diagnostic imaging equipment or a personal computer,
and automatically prints and ejects the received image data on the thermal paper.
2. Classication of this product
• According to the degree of protection of the applied part against electric shock: - (No
applied part)
• According to the degree of protection against harmful ingress of water: Ordinary
equipment (Enclosed equipment without protection against ingress of water)
• According to the degree of safety of application in the presence of a ammable anesthetic
mixture with air or with oxygen or nitrous oxide: Equipment not suitable for use in the
presence of a ammable anesthetic mixture with air or with oxygen or nitrous oxide
• According to the mode of operation: Continuous operation with intermittent loading
3. Follow the applicable laws and regulations in your country or region or the hospital rules
when disposing of this product or the accessories or consumables thereof.
DANGER:
EXPLOSION HAZARD.
DO NOT USE IN THE PRESENCE OF FLAMMABLE ANESTHETICS.
FRANÇAIS DEUTSCHITALIANO
NEDERLANDS
ESPAÑOL ENGLISH
DO NOT OPEN.
TO REDUCE THE RISK OF INJURY OR BURNS, DO NOT REMOVE COVER (OR
BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION:
When you dispose of the unit or accessories, you must obey the law in the relative area
or country and/or regulation in the relative hospital.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
The “Caution, hot surface” symbol indicates that the marked item may be hot
and should not be touched.
The “Nonionizing radiation” symbol
This symbol is intended to alert the user to read the operation and maintenance
(servicing) instructions before using the appliance, and to follow the directions.
This symbol is used to get the user’s attention.
The “STANDBY” symbol
The “direct current” symbol indicates that the equipment is suitable for direct
current only.
The “Caution, moving parts” symbol indicates that there are moving parts near
this symbol and they should not be touched.
The “Electro Static Discharge (ESD) warning” symbol indicates that trouble
(including equipment malfunction) due to static electricity may occur in certain
conditions.
: Manufactured on : to be combined with date code YYYY-MM
: Manufacturers Identication (name address)
: Serial number
: Authorised representative in the European Community
WARNING:
To prevent re or shock hazard, do not expose this appliance to rain or moisture.
Use the USB cable according to the recommendations as below, in order to comply with
EN60601-1-2.
The USB cable with appropriate plug should be 2 m long or shorter, comply with USB 2.0
standard High speed requirements and USB IF (USB Implementers Forum) approved.
This product is to be employed with medical equipment, just for reference purpose, not for
medical diagnostic purpose.
This equipment is not suitable for use in locations where children are likely to be present.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality
materials and components which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and accumulators,
at their end-of-life, should be disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol
means that the battery or accumulator contains a heavy metal at a certain concentration.
This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical and
electronic products, batteries and accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your local
community waste collection/recycling centre.
Please, help us to conserve the environment we live in!
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2012/19/EU Article 14
Information for users and Annex IX, and/or to the directive 2006/66/
EC Article 20 Information for end-users and Annex II.
WARNING:
The front panel may be heated to high temperature when this product is
damaged. This may cause burns. In such a case, stop the power supply of the
system.
FRANÇAIS DEUTSCHITALIANO
NEDERLANDS
ESPAÑOL ENGLISH
INSTRUCTIONS FOR MEDICAL USE
<according to the Medical Safety/EMC standard IEC/EN 60601-1-2>
MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC and
needs to be installed and put into service according to the EMC information provided in the
ACCOMPANYING DOCUMENTS.
Portable and mobile RF communications equipment can affect MEDICAL ELECTRICAL
EQUIPMENT.
Technical description
List of all cables and maximum length of the cable and other ACCESSORIES
Maximum length Reference page in this operation manual
DC power cord 2 m This page and the previous pages for safety
USB cable 2 m This page and the previous pages for safety
Thermal paper Page 3 for thermal paper, page 24 for accessories
WARNING:
The use of ACCESSORIES and cables other than those specied, with the exception of
cables sold by the manufacturer of the Model P95DW-DC as replacement parts for internal
components, may result in increased EMISSIONS or decreased IMMUNITY of the Model
P95DW-DC.
WARNING:
The Model P95DW-DC should not be used adjacent to or stacked with other equipment and
that if adjacent or stacked use is necessary, the Model P95DW-DC should be observed to
verify normal operation in the conguration in which it will be used.
Guidance and manufacturer’s declaration - electromagnetic emissions
The Model P95DW-DC is intended for use in the electromagnetic environment specied below. The
customer or user of the Model P95DW-DC should assure that it is used in such an environment.
Emissions test Compliance Electromagnetic environment - guidance
RF emissions
CISPR 11/EN 55011
Group 1 The Model P95DW-DC uses RF energy only for its internal
function. Therefore, its RF emissions are very low and are not
likely to cause interference in nearby electronic equipment.
RF emissions
CISPR 11/EN 55011
Class B The Model P95DW-DC is suitable for use in all
establishments, including domestic establishments and those
directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Guidance and manufacturer’s declaration - electromagnetic immunity
The Model P95DW-DC is intended for use in the electromagnetic environment specied below. The
customer or user of the Model P95DW-DC should assure that it is used in such an environment.
Immunity test IEC/EN 60601
test level
Compliance
level
Electromagnetic environment - guidance
Electrostatic
discharge (ESD)
IEC/EN 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or ceramic
tile. If oors are covered with synthetic
material, the relative humidity should be at
least 30%.
Electrical fast
transient/burst
IEC/EN 61000-4-4
±2 kV for power
supply lines
±1 kV for input/
output lines
±2 kV for power
supply lines
±1 kV for input/
output lines
Mains power quality should be that of a
typical commercial or hospital environment.
Power frequency
(50/60 Hz)
magnetic eld
IEC/EN 61000-4-8
3 A/m 3 A/m Power frequency magnetic elds should be at
levels characteristic of a typical location in a
typical commercial or hospital environment.
FRANÇAIS DEUTSCHITALIANO
NEDERLANDS
ESPAÑOL ENGLISH
Guidance and manufacturer’s declaration - electromagnetic immunity
The Model P95DW-DC is intended for use in the electromagnetic environment specied below. The
customer or user of the Model P95DW-DC should assure that it is used in such an environment.
Immunity test IEC/EN 60601
test level
Compliance
level
Electromagnetic environment - guidance
Portable and mobile RF communications
equipment should be used no closer to any
part of the Model P95DW-DC, including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter.
Recommended separation distance
Conducted RF
IEC/EN 61000-4-6
3 Vrms
150 kHz to 80
MHz
3 Vrms d=1.2
√P
Radiated RF
IEC/EN 61000-4-3
3 V/m
80 MHz to 2.5
GHz
3 V/m d=1.2√P 80 MHz to 800 MHz
d=2.3√P 800 MHz to 2.5 GHz
where P is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and d is the
recommended separation distance in meters
(m).
Field strengths from xed RF transmitters, as
determined by an electromagnetic site survey,a
should be less than the compliance level in each
frequency range.b
Interference may occur in the vicinity of
equipment marked with the following symbol:
NOTE 1. At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2. These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
a Field strengths from xed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast
cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due
to xed RF transmitters, an electromagnetic site survey should be considered. If the measured
eld strength in the location in which the Model P95DW-DC is used exceeds the applicable RF
compliance level above, the Model P95DW-DC should be observed to verify normal operation. If
abnormal performance is observed, additional measures may be necessary, such as reorienting or
relocating the Model P95DW-DC.
b Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.
Safety Notices for use in combination with other devices
1. All the equipments connected to this unit shall be certied according to Standard
IEC60601-1, IEC60950-1, IEC60065 or other IEC/ISO Standards applicable to the
equipments.
2.
When this unit is used together with other equipment in the patient area*, the equipment
shall be powered by a SELV power supply which is certied according to Standard
IEC60601-1 and provided with double insulation or reinforced insulation.
* Patient Area
R1.5 m
Recommended separation distances between portable and mobile RF communications
equipment and the Model P95DW-DC
The Model P95DW-DC is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the Model P95DW-DC can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile
RF communications equipment (transmitters) and the Model P95DW-DC as recommended below,
according to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d=1.2
√P
80 MHz to 800 MHz
d=1.2
√P
800 MHz to 2.5 GHz
d=2.3
√P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in meters (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to
the transmitter manufacturer.
NOTE 1. At 80 MHz and 800 MHz, the separation distance for higher frequency range applies.
NOTE 2. These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
Altri manuali per P95DW-DC
1
Indice
Altri manuali Mitsubishi Electric Stampante
Mitsubishi Electric
Mitsubishi Electric CP9000DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-D70DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-3800DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric D90-WIFI-1 Manuale utente
Mitsubishi Electric
Mitsubishi Electric D90-WIFI-1 Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-C60DW-WE Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-D90DW-SL Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-3800DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-M15 Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP9600DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP9800DW-S Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-3020DAU Guida alla configurazione
Mitsubishi Electric
Mitsubishi Electric CP9820DW-S Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP3020DE Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-D2E Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-D70DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric P95DW-DC Manuale utente
Mitsubishi Electric
Mitsubishi Electric P95DE Manuale utente
Mitsubishi Electric
Mitsubishi Electric CP-30DW Manuale utente
Mitsubishi Electric
Mitsubishi Electric P-95DW Manuale utente
