Mobatime METRO Manuale utente

Mounting instructions

METRO Outdoor clocks, round, single- and double-sided

Before installation of the clock please read the manual carefully.

References to the Instruction Manual

1. The information in this Instruction Manual can be changed at any time without previous

notice.

2. This Instruction Manual has been composed with utmost care, in order to explain all details

in respect of the operation of the product. Should you, nevertheless, have questions or

discover errors in this Manual, please contact us.

3. We do not answer for direct or indirect damages, which could occur, when using this

Manual

4. Please read the instructions carefully and start the setting-up of the product, only once you

have correctly understood all information for the installation and of the operation.

5. The installation must only be carried out by skilled staff.

6. It is prohibited to reproduce, to store in a computer system or to transfer this publication in

a way or another, even part of it. The copyright remains with all the rights with BÜRK

MOBATIME GmbH, D-78026 VS-Schwenningen and MOSER-BAER SA – CH 3454

Sumiswald / SWITZERLAND.

Table of contents Page

1 Mounting instructions .....................................................................................................4

1.1 Building department / authority permit.........................................................................4

1.2 General rules...............................................................................................................4

1.3 Handling reference......................................................................................................4

1.4 Internal Connections...................................................................................................4

1.5 External Connections..................................................................................................4

1.6 Open the clock............................................................................................................5

1.7 Exchange of movement and dial.................................................................................6

1.8 Close the clock............................................................................................................6

2 Mounting types ................................................................................................................7

2.1 Wall mounting E (Mounting type zz = 00)....................................................................7

2.2 Wall bracket WA (Mounting type zz = 10).................................................................8

2.3 Ceiling bracket DA (Mounting type zz = 20).............................................................8

2.4 Central post ZM (Mounting type zz = 40)...................................................................9

2.5 Lateral mounting to round post KRL (Mounting type zz = 30).................................9

2.6 Lateral mounting to square post KVL (Mounting type zz = 31)................................9

1 Mounting instructions

1.1 Building department / authority permit

If necessary a building department / authority permit should be requested before mounting.

1.2 General rules

The mains supply for the clock must be installed only by a licensed electrician.

While the national installation regulations must be adhered.

Please provide a cable with a wire cross section of maximum 1.5 mm2.

The clock is not equipped with a mains plug. An all-pole disconnecting device and a fuse for

movement and lighting power supply must be provided in the on-site supply.

The fuses should be chosen according to the power consumption of the device.

For all maintenance and cabling work, the clock has to be separated from mains.

For safety reasons avoid to look directly into the LEDs.

1.3 Handling reference

1. The clock should be transported upright in its original packaging and must be stored dry.

2. Clean the cover glas with wet (lether-) cloth.

3. Never use solvents, aerosol or organic cleaning products.

4. The housing is to treat with standard cleaning agents.

1.4 Internal Connections

The internal wiring is made in the factory. It’s important not to modify the internal wiring.

1.5 External Connections

Dismantle the insulation of the connecting wires on a length of 8 – 9 mm and insert the wires up to the

isolation in the terminal. The spring terminal can be opened with a screw driver size 0.

Phase and neutral wire must be kept together close to the terminal using a cable tie.

1.6 Open the clock

1. Unscrew the 3 screws of the glass ring, pull of the glass ring with the glass and deposit it carefully.

2. Untighten and turn the dial fixation flaps. Carefully pull the dial together with the movement out from

clock housing und disconnect the electrical terminals from the clock movement.

3. Deposit the dial with the movement and hands carefully.

Dial fixation flap

Fixation screws for glass mounting ring

1.7 Exchange of movement and dial

1. Open the clock according to chapter 1.6

2. Before you exchange the dial, be sure that the hands show 12:00 position.

Check movement manual to set the hands to 12:00 position (DIP switch 1 = ON for 190 series

movements).

3. Loosen the Allen screw for the second- and minute hand and remove the hands from the axis.

4. Carefully remove the hour hand from the axis (clench bushing).

5. Use the special wrench to loosen the central nut of the movement and remove it from the shaft.

6. Fix the movement into the new dial (or the new movement into the existing dial) – connectors of the

movement must be at 6:00 position (buttom side) – and tighten the central nut with a torque of 4.5 Nm.

7. Connect the timesignal with the movement and check the correct time. Don’t forget to switch off the

12:00 position command at the movement (e.g. 190 series movements: DIP switch 1 = OFF).

8. Close the clock according to chapter 1.8.

1.8 Close the clock

1. Connect the electrical terminal(s) to the movement (time signal, power).

2. Put the dial to the correct position.

3. Turn the dial fixation flaps and tighten all four screws.

4. Pull the glass ring with the glass carefully over the housing frame and fix the ring with the 3 screws.

Check, that the cables do not affect the clock illumination with shadows on the dials.

2 Mounting types

Nominal-Single-sided (E)

Type Double-sided (WA, DA, KRL, KVL, ZM)

Type

50cm MTv.50.R1.www.xxx.y.zz MTv.50.R2.www.xxx.y.zz

60cm MTv.60.R1.www.xxx.y.zz MTv.60.R2.www.xxx.y.zz

80cm MTv.80.R1.www.xxx.y.zz MTv.80.R2.www.xxx.y.zz

Legend: v = Illumination (0 = no illumination, 2 = LED illumination)

www = Movement code, see document TE-800800 und TE-801006

xxx = Dial: 100: with MOBATIME logo, 101: without logo

y = Cover glass (1 = Mineral glass, 2 = Security glass, 3 = Polycarbonate glass)

zz = Mounting types: 00 = Wall mounting (single-sided, E)

10 = Wall mounting bracket (WA)

20 = Ceiling mounting bracket (DA)

30 = Side pole mounting, round Ø 133 (KRL)

31 = Side pole mounting, square 150 x 150 (KVL)

40 = Cantral post

2.1 Wall mounting E (Mounting type zz = 00)

The electrical cables can be inserted through the two grommets in the back wall of the clock.

Before the mounting, all connection cables has to be separated from mains!

After inserting the cables, fix the clock with the 3 screws (M10) to the wall, using the lugs outside of the

case.

Nominal-A B C D

50cm 566 176 160 594

60cm 666 176 180 694

80cm 866 176 180 894

2.2 Wall bracket WA (Mounting type zz = 10)

The electrical cables can be inserted through the

mounting bracket (cable entry in the middle with

Ø 85 mm).

Before the mounting, all connection cables has to

be separated from mains!

Drill the holes according to the dimenstion drawing of

the flange and prepare them with dowels. Set four "set

screws" into the dowels. Insert the cables through the

bracket into the clock and fix the clock with 4 washers

and 4 nuts.

Flange

2.3 Ceiling bracket DA (Mounting type zz = 20)

The electrical cables can be inserted through the

mounting bracket (cable entry in the middle with

Ø 85 mm).

Before the mounting, all connection cables has to

be separated from mains!

Drill the holes according to the dimenstion drawing of

the flange and prepare them with dowels. Set four

"set screws" into the dowels. Insert the cables through

the bracket into the clock and fix the clock with 4

washers and 4 nuts.

Flange

Nominal -A B

50 566 150

60 666 150

80 866 150

Nominal -A B

50 566 150

60 666 150

80 866 150

2.4 Central post ZM (Mounting type zz = 40)

Prepare the mast with a suitable fundament. For the

dimension of the fundament and the pole, the wind force

has to be taken into consideration. The electrical cables

has to be inserted through the pole.

Before the mounting, all connection cables has to be

separated from mains!



Nominal -ABmin. Bmax. C

50cm 566 40 76 90

60cm 666 40 76 90

80cm 866 60 102 130

2.5 Lateral mounting to round post KRL

(Mounting type zz = 30)

The electrical cables has to be inserted through the

pole.

Before the mounting, all connection cables has to

be separated from mains!

The fixation to the round pole can be done with the

clamping fixture and the 4 screws with nuts.

For standard pole dimension: 133.5 mm

Other dimensions on request.

2.6 Lateral mounting to square post KVL

(Mounting type zz = 31)

The electrical cables has to be inserted through the

pole.

Before the mounting, all connection cables has to

be separated from mains!

The fixation to the square pole can be done with the

clamping fixture and the 4 screws with nuts.

For standard pole dimension: 150 mm

Other dimensions on request.

Nominal -A B

50 566 150

60 666 150

80 866 150

Altri manuali per METRO

Indice

Altri manuali Mobatime Orologio

Mobatime

Mobatime Metroline Manuale utente

Mobatime

Mobatime ECO-DC Manuale utente

Mobatime

Mobatime DTS 4801.masterclock Manuale utente

Mobatime

Mobatime SLH-DC series Manuale utente

Mobatime

Mobatime PROFILINE Series Manuale utente

Mobatime

Mobatime Profiline Manuale utente

Mobatime

Mobatime ECO-SLH-DC Series Manuale utente

Mobatime

Mobatime SEW 30 Manuale utente

Mobatime

Mobatime METROLINE Guida

Mobatime

Mobatime MOBALINE Cristalys Date Manuale utente

Mobatime

Mobatime MOBALine TREND Manuale utente

Mobatime

Mobatime ECO-M-DSC Series Manuale utente

Mobatime

Mobatime METRO Manuale utente

Mobatime

Mobatime HN 60 Manuale utente

Mobatime

Mobatime TREND NTP Series Manuale utente

Mobatime

Mobatime ECO-M-DC Series Manuale utente

Mobatime

Mobatime EuroTime Center ETC Manuale del proprietario

Mobatime

Mobatime DSC. 250.4 Manuale utente

Mobatime

Mobatime DK series Manuale utente

Mobatime

Mobatime ECO DC series Manuale utente

Mobatime

Mobatime Mini Master clock HN 60 Manuale utente

Mobatime

Mobatime Flex Manuale utente

Mobatime

Mobatime EuroTime Center ETC 12 Manuale utente

Mobatime

Mobatime PROFILINE round Guida

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente