Molex 78172 Series Manuale utente

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 1 of 6

Revi ion: A Revi ion Date: 08-17-09

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP TOOL

SPECIFICATION SHEET

Order No. 63819 4800

FEATURES

% A full cycle ratcheting hand tool en ure complete crimp

% Thi tool i de igned to be u ed with reeled product due to the mall ize of the connector

% Thi tool i de igned for prototype work only and i not de igned for production

% The reeled product mu t be cut into 5-inch trip to be proce ed in thi hand tool

% Thi tool i IPC/WHMA A-620 Cla 2 compliant a indicated

% Thi tool i RoHS compliant, however RoHS compliant i not required

SCOPE

Product : 1.20mm (.047”) Pitch Pico-EZmate™ Wire-to-Board Crimp Terminal, 28 AWG.

Insulation Diameter

Wire Size IPC/WHMA A620 Terminal



 Strip Length

Terminal

Series No.

Terminal Order No.

Reel Form Only AWG

mm²

mm In. mm In. mm In.

78172-0410

78172 78172-0411 28 0.08 0.55-0.70

.022-.028

0.55-0.70

.022-.028

0.90-1.30

.035-.051

To achieve optimum IPC-A620 in ulation crimp , u e thi in ulation OD range.

Overall in ulation OD pecification for terminal.

Cu tomer to cut off terminal from reel: 0.05mm (.002”) maximum Cut-off Tab.

DEFINITION OF TERMS

The above terminal drawing i a generic terminal repre entation. It i not an image of a terminal li ted in the

cope.

TYPE 7

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 2 of 6

Revi ion: A Revi ion Date: 08-17-09

INSULATION CRIMP FORM

Thi crimp terminal i de igned for miniaturization; therefore, each dimen ion of in ulation crimp portion appear

mall a compared to the terminal material thickne . In order to avoid in ulation piercing the crimp form by the

in ulation barrel, coining i provided in ide of the in ulation barrel. For thi rea on, variou crimp form will occur at

the tip of the in ulation crimp barrel hown in the figure below.

The e crimp form maybe changed completely by a mall change in the wire, in ulation punch, or terminal.

The e crimp form are ati factory for original function of the in ulation crimp portion and it i confirmed that all of

the e form below are acceptable in ulation crimp .

CONDITIONS:

After crimping, the conductor profile hould mea ure the following.

Conductor Crimp (Ref) Insulation Crimp (Ref)

Wire Size Height Width Height Width

Pull Force

Minimum

Terminal

Series No

AWG

mm2

mm In. mm In. mm In. mm In. N Lb.

78172 28 0.08 0.44-0.48

.017-.019

0.85

.033

0.77

.030

0.85

.033

10.0

2.25

OPERATION

CAUTION: In tall only Molex terminal li ted above with thi tool. Do not crimp hardened object a

damage can occur to the tool or die.

Open the tool by queezing the handle together, at the end of the clo ing troke, the ratchet mechani m will

relea e the handle , and the hand tool will pring open.

Crimping Terminals

1. Select the de ired terminal li ted in the preceding chart .

2. Cut a trip of the terminal approximately 5.0” off the reel. Po ition the terminal trip into the lot of the carrier

guide with terminal facing forward.

3. Pu h the trip in until it lock into the (2) detent in the carrier guide and a terminal i centered with the punch

ne t. See Figure 1.

4. Partially clo e the jaw of the hand tool by queezing the handle until you hear the fi t click of the ratchet.

5. From the top of the hand tool in ert the pre- tripped wire into the terminal.

6. Compre the terminal by queezing the tool handle until the ratchet mechani m cycle ha been completed.

Relea e handle to open the jaw .

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 3 of 6

Revi ion: A Revi ion Date: 08-17-09

Note: The tamper proof ratchet action will not relea e the tool until it ha been fully clo ed.

7. Lift up the crimped terminal from the

terminal locator.

8. Vi ually in pect the crimped terminal

for proper crimp location.

9. If crimping more wire advance the

terminal trip by (1) detent until the

terminal i centered with the punch

ne t.

10. Repeat thi procedure until all the

de ired terminal are crimped on the

trip.

Maintenance

It i recommended that each operator of

the tool be made aware of, and re pon ible

for, the following maintenance tep :

1. Remove the pla tic handle from the metal tool

frame by removing the crew and remove du t,

moi ture, and other contaminant with a clean bru h,

or oft, lint free cloth.

2. Do not u e any abra ive material that could

damage the tool.

3. Make certain all pin ; pivot point and bearing

urface are protected with a thin coat of high quality

machine oil. Do not oil exce ively. The tool wa

engineered for durability but like any fine piece of

equipment it need cleaning and lubrication for a

maximum ervice life of trouble free crimping. Light

oil u ed at the pivot point every 5,000 crimp or 3

month , will ignificantly enhance the tool life.

4. Wipe exce oil from hand tool, particularly from

crimping area.

5. When tool i not in u e, keep the handle clo ed to

prevent object from becoming lodged in the

crimping die , and tore the tool in a clean, dry area.

Miscrimps or Jams

Should thi tool ever become tuck or jammed in a partially clo ed po ition, Do Not force the handle open or

clo ed. The tool will open ea ily by pre ing the ratchet relea e lever up. See Figure 2.

SLIDE WIRE

INTO THE

PUNCH NEST

Figure 1

LOCKS IN THE

TERMINAL STRIP

SLIDE TERMINAL

STRIP INTO THE

CARRIER GUIDE

CRIMP TOOL OPEN

WIRE

RATCHET

RELEASE LEVER

Figure 2

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 4 of 6

Revi ion: A Revi ion Date: 08-17-09

NUMBERED ADJUSTMENT

WHEEL

Figure

TURN CLOCKWISE (CW) OR

COUNTER CLOCKWISE (CCW)

TO ADJUST THE PRE LOAD

TURN WITH A SMALL

SCREW DRIVER

REMOVE THE LOCKING 2MM SCREW

How to Adjust Tool Preload

It may be nece ary over the life of the tool to adju t tool handle preload force. Li ted below are the tep

required to adju t the crimping force of the hand tool to obtain proper crimp condition :

1. Remove the 2mm locking crew from the numbered adju ting wheel u ing a crew driver. See Figure 3.

2. U ing the ame crew driver turn the adju tment wheel to the next highe t number.

Note: The uneven number are in clockwi e (CW) direction and the even number are counter clockwi e

(CCW).

3. Example: If the preload i et at number 5, then to increa e the preload, turn the adju tment wheel until the 6th

po ition i located over the 2mm locking crew tapped hole. If it i nece ary to move to the 7th po ition, then

the adju tment wheel hould be turned counter clockwi e (CCW) until the 7th po ition i over the 2mm locking

crew tapped hole.

4. Replace the 2mm locking crew, aligning the neare t notch in the etting wheel to locking crew.

5. Check the crimp pecification and conduct a pull te t after tool handle preload force i adju ted. Repeat

the e tep until the de ired re ult i obtained.

Warranty

Thi tool i for electrical terminal crimping purpo e only. Thi tool i made of the be t quality material . All vital

component are long life te ted. All tool are warranted to be free of manufacturing defect for a period of 30

day . Should uch a defect occur, we will repair or exchange the tool free of charge. Thi repair or exchange will

not be applicable to altered, mi u ed, or damaged tool . Thi tool i de igned for hand u e only. Any clamping,

fixturing, or u e of handle exten ion void thi warranty.

CAUTION: Molex crimp pecification are valid only when u ed with Molex terminal and tooling.

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 5 of 6

Revi ion: A Revi ion Date: 08-17-09

CAUTIONS:

1. Manually powered hand tool are intended for low volume, prototyping, or field repair. Thi tool i NOT

intended for production u e. Repetitive u e of thi tool hould be avoided.

2. In ulated rubber handle are not protection again t electrical hock.

3. Wear eye protection at all time .

4. U e only the Molex terminal pecified for crimping with thi tool.

Certification

Molex doe not certify or re-certify hand tool but rather upplie the following guideline for cu tomer to re-certify

hand tool .

% Thi tool i qualified to pull force only. To re-certify, crimp a terminal to a wire, which ha been tripped

12.7mm (1/2”) long, o there i no crimping of the in ulation. Pull the terminal and wire at a rate no fa ter than

25mm (1.00”) per minute. See the Molex web ite for the Quality Crimp Handbook for more information on pull

te ting.

% If the tool doe not meet minimum pull force value , handle preload hould be increa ed and the pull te t rerun,

(See How To Adju t Preload).

% When the hand tool i no longer capable of achieving minimum pull force, it hould be taken out of ervice and

replaced.

Hand Crimp Tool 1.20mm (.047”) Pitch Pico-EZmate™ Crimp Terminal

Doc No: ATS-6381948000 Relea e Date: 08-17-09 UNCONTROLLED COPY Page 6 of 6

Revi ion: A Revi ion Date: 08-17-09

Figure

PARTS LIST

Item Order No Description Quantity

REF 63819 4800 Hand Crimp Tool Figure 4

1 63819-4870 Tool Kit 1

2 11-11-0320 Spring (Ratchet) 1

3 63600-0479 Spring (Main) 1

4 69008-0972 Adju ter Wheel 1

Americas Headquarters

Li le, Illinoi 60532 U.S.A.

1-800-78MOLEX

[email protected]

Far East North Headquarters

Yamato, Kanagawa, Japan

81-462-65-2324

[email protected]

Far East South Headquarters

Jurong, Singapore

65-6-268-6868

fe info@molex.com

European Headquarters

Munich, Germany

49-89-413092-0

[email protected]

Corporate Headquarters

2222 Wellington Ct.

Li le, IL 60532 U.S.A.

630-969-4550

Fax: 630-969-1352

Visit our Web site at http://www.molex.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali molex Utensili per crimpatura

molex

molex 63827-0470 Manuale utente

molex

molex MOLEX Manuale utente

molex

molex 63825-6770 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex RHT 2251-CC Manuale utente

molex

molex 98897 Manuale utente

molex

molex 35745 Series Manuale utente

molex

molex 63811-9370 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex AT 2100 Manuale utente

molex

molex 63819-1500 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 64003-0800 Manuale utente

molex

molex 63823-0400 Guida utente

molex

molex Avikrimp AT 5762 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex ServiceGrade 64016-0038 Manuale utente

molex

molex 64001-2800 Manuale utente

molex

molex 63823-6470 Manuale utente

molex

molex 63827-6270 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex CS 150 Manuale utente

molex

molex 35745 Series Manuale utente

molex

molex 63823-7970 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente

molex 78172 Series Manuale utente

Manuali Utensili per crimpatura popolari di altre marche