monolith 43241 Manuale utente
MTM 3-Way Powered Desktop Speakers
P/N 43241
User's Manual
2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra
attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind. Do not
place drinks or other containers with moisture on or near the
device. If moisture does get in or on the device, immediately
remove it from its power source and allow it to fully dry before
reapplying power.
•Do not touch the device, the power cord, or any other connected
cables with wet hands.
•If operating this speaker in a humid environment, ensure that no
condensation occurs. Condensation could cause damage to the
speaker cone and could cause a short in the amplifier, which in turn
could cause fire or severe electric shock.
•Do not install this device on an unstable surface where it could fall
and cause either personal injury or damage to the device and/or
other equipment.
•Do not expose this device to excessive vibration or extreme force,
shock, or fluctuations in temperature or humidity.
•Avoid prolonged exposure to excessive volume levels, which could
cause hearing damage. Reduce the volume to minimum before
using these speakers, then increase the volume to a comfortable
listening level.
3
•Do not expose this device to excessively high temperatures. Do not
place it in, on, or near a heat source, such as a fireplace, stove,
radiator, etc. Do not leave it in direct sunlight.
•Do not place or install this device in an area where it can be
exposed to excessive amounts of dust, humidity, oil, smoke, or
combustible vapors.
•Prior to operation, check the unit and power cord for physical
damage. Do not use if physical damage has occurred.
•Before plugging the unit into a power outlet, ensure that the outlet
provides the same type and level of power required by the device.
•Unplug this device from the power source when not in use.
•Take care to prevent damage to the power cord. Do not allow it to
become crimped, pinched, walked on, or become tangled with
other cords. Ensure that the power cord does not present a tripping
hazard.
•Never unplug the unit by pulling on the power cord. Always grasp
the connector head or adapter body.
•Ensure that power is turned off and disconnected before making
any electrical connections.
•Clean using a soft, dry cloth only. Do not use chemical cleaners,
solvents, or detergents. For stubborn deposits, moisten the cloth
with warm water.
•This device has no user serviceable parts. Do not attempt to open,
service, or modify this device.
4
FEATURES
•One 1.25" silk dome tweeter in each speaker
•Two 4" woofers in each speaker
•Two 5.25" passive radiator drivers in each speaker
•Separate 50-watt Class D amplifiers for each speaker
•50Hz ~ 20kHz frequency response
•Bluetooth® 5 with Qualcomm® aptX™ HD codec
•Subwoofer output
•3.5mm headphones output
•Stereo analog RCA, digital optical S/PDIF, USB Type-C®, and
Bluetooth inputs
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring
that your ordering, purchasing, and delivery experience is second to none.
If you have any problem with your order, please give us an opportunity to
make it right. You can contact a Monoprice Customer Service
representative through the Live Chat link on our website
www.monoprice.com or via email at [email protected]. Check the
website for support times and links.
5
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all
the items listed below. If anything is missing or damaged, please contact
Monoprice Customer Service for a replacement.
1x Primary Speaker
1x Secondary Speaker
1x Remote Control
2x AAA Batteries
1x Speaker Interconnect Cable
1x Stereo RCA Audio Cable
1x Foot Mat
1x AC Power Cable
1x User's Manual
6
PRODUCT OVERVIEW
Primary Speaker Front Panel
1. Headphone: 3.5mm stereo
headphone jack.
2. Tweeter: One 1.25" silk dome
tweeter.
3. Woofers: Two 4" woofers.
4. Volume: Multifunction knob and
source LED indicators. With the
speakers powered on, rotate the
knob to increase or decrease the
volume level. With the speakers
powered off, momentarily press
the knob to turn the speakers on.
With the speakers powered on,
momentarily press the knob to
cycle through the inputs in the
order BT (Bluetooth®), USB, OPT (optical), and RCA. With the
speakers powered on, press and hold the knob for 2 seconds to put
the speakers into standby mode.
5. IR: Infrared receiver for receiving IR signals from the included
remote control.
7
Primary Speaker Side Panels
6. Passive Radiators: Two 5.25" passive radiators (one on each side).
8
Primary Speaker Rear Panel
1. AC INPUT: IEC 60320 C8
connector for connecting
the included AC Power
Cord.
2. USB: USB Type-C® input.
3. OPTICAL: Digital optical
S/PDIF input.
4. ANALOG INPUTS: Stereo
RCA inputs.
5. SUBWOOFER OUTPUT:
Mono RCA output for
connecting a subwoofer
(available separately).
6. SPEAKER OUT: Connectors
for connecting the
Secondary Speaker using
the included Speaker Interconnect Cable.
7. POWER: Switch for turning the speakers on or off. When the switch
is in the ON position, the auto standby function will put the
speakers into standby mode after 30 minutes of no audio input.
When in standby mode, the speakers will automatically power on
when an audio signal is detected.
9
Remote Control
1. ON/STANDBY: Press the button to turn the
speakers on or to put them into standby
mode. Note that the POWER switch on the
Primary Speaker Rear Panel must be in the
ON position for this button to function.
2. TONE DEFEAT: Press the button to bypass
the tone controls for an unaltered audio
signal, without changing the tone control
settings. Press the button again to reinsert
the tone controls into the audio signal path.
3. PAIR: Press the button to enter Bluetooth®
pairing mode.
4. TONE WHEEL: The TONE WHEEL allows you to boost or cut the low
frequency (BASS+/BASS-) and high frequency (TREBLE+/TREBLE-)
portions of the audio signal.
5. 0: If the 0button is pressed within 20 seconds of using the TONE
WHEEL, the last tone control used (BASS or TREBLE) will be reset to
0. If the button is pushed without having used the TONE WHEEL in
the last 20 seconds, both the BASS and TREBLE tone controls will
be reset back to 0.
6. SOURCE: Press the button to cycle through the inputs in the order
BT (Bluetooth®), USB, OPT (optical), and RCA.
7. VOLUME: Use the buttons to increase or decrease the volume level.
8. MUTE: Press the button to turn audio mute on or off.
10
INSTALLATION
Ensure that power is turned off and disconnected on all equipment to be
connected before making any electrical connections.
1. Ensure that the POWER switch on the Primary Speaker Rear Panel is
in the OFF position.
2. Place the Primary Speaker and Secondary Speaker in their intended
locations.
3. Connect one end of the included Speaker Interconnect Cable to
the SPEAKER IN connectors on the Secondary Speaker Rear Panel,
then connect the other end to the SPEAKER OUT connectors on the
Primary Speaker Rear Panel.
4. (Optional) Plug one end of the included Stereo RCA Audio Cable
into the ANALOG INPUTS RCA jacks on the Primary Speaker Rear
Panel, the plug the other end into the RCA line output on your
audio source device.
5. (Optional) Plug one end of a digital optical S/PDIF cable (available
separately) into the OPTICAL port on the Primary Speaker Rear
Panel, then plug the other end into the digital optical output on
your audio source device.
6. (Optional) Plug one end of a USB-C® cable (available separately)
into the USB port on the Primary Speaker Rear Panel, then plug the
other end into the USB output on your laptop or computer.
7. (Optional) Plug one end of a mono RCA cable (available separately)
into the RCA input on a subwoofer (available separately), then plug
the other end into the SUBWOOFER OUTPUT jack on the rear panel.
Indice
Altri manuali monolith Altoparlanti
