Monoprice 38161 Manuale utente

Indice

Altri manuali Monoprice Interruttore

Monoprice

Monoprice 30919 Manuale utente

Monoprice

Monoprice Blackbird 36632 Manuale utente

Monoprice

Monoprice BLACKBIRD 44556 Manuale utente

Monoprice

Monoprice 36650 Manuale utente

Monoprice

Monoprice Blackbird 33417 Manuale utente

Monoprice

Monoprice HDX-301 Manuale utente

Monoprice

Monoprice 10319 Manuale utente

Monoprice

Monoprice Blackbird 33418 Manuale utente

Monoprice

Monoprice HD-411E3 Manuale utente

Monoprice

Monoprice HD-140E3-3D 1x4 Pro Series Manuale utente

Monoprice

Monoprice Blackbird 36633 Manuale utente

Monoprice

Monoprice 31056 Manuale utente

Monoprice

Monoprice 36652 Manuale utente

Monoprice

Monoprice 38295 Manuale utente

Monoprice

Monoprice HDX-401E Manuale utente

Monoprice

Monoprice 33416 Manuale utente

Monoprice

Monoprice Blackbird 21614 Manuale utente

Monoprice

Monoprice 4x2 HDMI Manuale utente

Monoprice

Monoprice 24568 Manuale utente

Monoprice

Monoprice 3407 Manuale utente

Monoprice

Monoprice HRM-2214F Manuale utente

Monoprice

Monoprice 36737 Manuale utente

Monoprice

Monoprice Blackbird Manuale utente

Monoprice

Monoprice Blackbird 31057 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente

1

8-Channel Speaker Zone Hub

P/N 38161

Quick Install Guide

INTRODUCTION

This 8-Channel Speaker Zone Hub is designed to connect up to eight pairs of speakers to a

single amplifier or receiver. It uses removable terminal blocks for easy connection for the

speaker wires. Note that this speaker selector does not include impedance matching

circuitry, so the use of impedance matching volume controls are highly recommended to

prevent damage to the amplifier caused by low impedance loads.

INSTALLATION

Perform the following steps to install this speaker selector.

1. Remove one of the black colored terminal blocks from the rear of the speaker

selector.

2. Strip approximately 1/4" of insulation from each end of each speaker wire.

3. Using a small flathead screwdriver, loosen the screws on the terminal block.

4. Insert each end of the left channel positive speaker wire into the L+ terminal and

the negative speaker wire into the L- terminal, then tighten the screws to secure

them in place.

5. Insert each end of the right channel positive speaker wire into the R+ terminal and

the negative speaker wire into the R- terminal, then tighten the screws to secure

them in place.

2

6. Insert the terminal block into the rear of the speaker selector.

7. Connect the left and right channel speaker wires into the terminals on your speaker,

taking care to match the polarity.

8. Repeat for the other seven speakers and black terminal blocks.

9. Remove the red colored terminal block from the rear of the speaker selector.

10. Strip approximately 1/4" of insulation from each end of each speaker wire.

11. Using a small flathead screwdriver, loosen the screws on the terminal block.

12. Insert each end of the left channel positive speaker wire into the L+ terminal and

the negative speaker wire into the L- terminal, then tighten the screws to secure

them in place.

13. Insert each end of the right channel positive speaker wire into the R+ terminal and

the negative speaker wire into the R- terminal, then tighten the screws to secure

them in place.

14. Insert the terminal block into the rear of the speaker selector.

15. Connect the left and right channel speaker wires into the terminals on your

amplifier, taking care to match the polarity.