Morgana AutoFold Pro Manuale utente
ISSUE 7
MAY
2011
DOCUMENT
FOLDING MACHINE
OPERATORS MANUAL
184-011
AutoFold Pro
Website: www.morgana.co.uk
Facsimile: ( 01908 ) 692399Telephone:
United KingdomMorgana Systems Limited
( 01908 ) 608888
Page 2
INDEX
FOLDING
INTRODUCTION & SPECIFICATION
PAGE 4
SAFETY Do’s & Don’ts 5
THE AutoFold Pro
7
The Morgana AutoFold Pro
Labeled Photograph
OPERATING THE AutoFold Pro
8
8
TOUCHSCREEN OPERATION
10
11
13
16
17
18
20
21
23
24
25
26
29
REMOVING PAPER JAMS 30
TROUBLE SHOOTING
31
31
31
31
31
31
Adjusting the Tilt of the Feed Bed
Fitting the Transfer Bed Assembly to the Autocreaser and
Aligning the Machines
Touchscreen Layout
Paper Settings Page
Roller Gap Set Page
Feed Bed Fans Settings Page
Folds in ‘Set By Fold’ mode
Folds in ‘Set By Position-’ mode
Example of ‘Set By Position’ mode
Delivery Settings Page
Status Screen
Running the Job
Setting the machine to operate in manual sheet feed mode
Store Pages
Tools Menu
Paper crease out of square
Paper fold out of square
Paper Jamming
Machine will not start
Paper not feeding
Cracking of the printed material along the crease
Fold Settings Pages
Crease Position Inaccuracy 31
Page 3
SYSTEM
INDEX
Sheet did Not Arrive
ERROR SCREENS
02 32
09 32
10 33
11 33
12 33
13 34
45 34
DISPATCH KIT 36
ACCESSORIES AND OPTIONS 37
RECOMMENDED SPARES 38 - 39
01 32
MACHINE CALIBRATION HISTORY SHEET 40
FUSE POSITIONS & RATINGS 41
PRODUCT RECYCLING AND DISPOSAL 42
FUSE POSITIONS AND RATINGS 43
Paper Crunch
Clip 1 NOT Clear
Clip 1 NOT Blocked
Clip 2 NOT Clear
Clip 2 NOT Blocked
Overlap
Sheets Too Close
AutoFold Pro
INTRODUCTION AND SPECIFICATION
The is a self powered, stand alone folding machine with an innovative new
vacuum controlled sheet alignment system which has been designed to take pre-creased
stock from a wide range of both Morgana and 3rd party creasing machines.
The AutoFold Pro features the unique Flying Knife Folding System used successfully in the
much acclaimed Digifold which allows folding of most stocks from 0.1mm, reducing the
possibility of scratching, marking or cracking of the substrate as is often associated with
conventional folding systems.
A maximum paper thickness cannot be specified, as this is governed by the hardness of
the substrate and the type of fold required; but in most cases stocks up to 0.35mm should
present no problems providing they are properly pre-creased.
1 phase 110 / 115v 60Hz
Sound Power Level (Connected to an Autocreaser Pro 33).....................77.0 decibels
*As part of our continued product improvement plan, specifications and information
published in this manual are subject to change without notice.
All specifications are dependant on application, type of stock, temperature, RH and print
engine used.
Specifications quoted were measured on uncoated and unprinted stock.E&OE.
AutoFold Pro
It is to note that to prevent cracking, when using dry ink or toner based print
engines, the material be fully acclimatised for at least 48 hours before putting an
image onto the paper.
Feeding System ................................................ Conveyor Vacuum Sheet Alignment
Input Bed Height ...............................................Adjustable from 850mm to 1000mm
Max. Sheet Size ................................................600mm x 385mm (24” x 15”)
Min. Sheet Size .................................................210mm x 140mm (8.3” x 5.5”) (dependant
on stiffness of paper and type of fold).
Max. Paper Thickness ................................... 0.40mm (varies according to hardness,
type of fold, and substrate).
Min. Paper Thickness ....................................... 0.11mm
Max. No. Folds per Sheet.................................. 2
Max. No. Stored Programmes ...........................Unlimited
Min. Repeat Fold Distance ................................70
Min. Fold Distance from Leading Edge .............50mm (1.96”) (depending on paper weight)
IMPORTANT
must
IMPORTANT
Note:
the operating environment should be controlled to a temperature between
16° C and 27° C Maximum.
(varies according to hardness,
type of fold, and substrate).
mm (2.75”) (depending on paper weight)
Min. Fold Distance from Tail Edge .................... 50mm (1.96”) (depending on paper weight)
Min. Fold Length ............................................... 70mm (2.75”)
Speed per Hour (A4 in half)............................... 6240 sheets (When used with a Morgana
Autocreaser; set on speed 3, Pulsed).
Dimensions ....................................................... L: 1700mm H: 1220mm W: 680mm
L: (66.9”) H: (48”) W: (26.8”)
Weight ...............................................................128Kgs (+50Kgs packing)
Power Requirement .......................................... 1 phase 220 / 240v 50hz
Specification
The production speed varies according to the material size and
the fold type.
Page 4 FOLDING
INTRODUCTION
AutoFold Pro
Page 5
SYSTEM
Safety Do’s & Don’ts
Safety Do’s & Don’ts
Do - read this operator manual fully before operating the machine.
Do - operate with the designated AC current only. Use an exclusive outlet, as
overloading may cause fire or an electric shock.
Do - install the power cord out of the way to avoid a tripping hazard.
Do - make sure that the mains inlet connector is always easily accessible.
Do not - install the machine in an unstable place such that it tilts or shakes.
Do not - unplug the plug or unplug the power cord from the outlet with a wet hand,
this can cause an electric shock.
Do not - unscrew and remove any covers from the machine, as it can cause an
electric shock or injury.
Do not - place receptacles containing liquids on any surface.
Do not - adjust any part of the machine whilst rollers are running
Do not - operate the machine with loose or trailing clothing or loose hair.
Do not - under any circumstances adjust the paper gate when the machine is
switched on.
REGLES DE SECURITE : « A FAIRE » ET « A NE PAS FAIRE »
Lire ce mode d'emploi avant d'utiliser la machine.
Respecter l'alimentation électrique indiquée. Brancher sur une prise séparée
car une surcharge peut entraîner un incendie ou un choc électrique.
Installer le cordon d'alimentation de manière à ne pas pouvoir
trébucher par dessus.
Ménager un accès libre à la prise de courant.
Ne pas installer la machine sur une surface non plane, afin d'éviter
qu'elle ne penche ou ne vibre.
Ne pas installer la machine sur une surface non plane, afin d'éviter
qu'elle ne penche ou ne vibre.
Ne démonter et enlever aucun carter de la machine, par crainte de décharge
électrique ou de blessure.
Ne pas placer de récipient contenant un liquide sur la machine.
N'effectuer aucun réglage pendant que les rouleaux fonctionnent.
Ne pas porter de vêtements flottants et rassembler les cheveux longs
lors de l'utilisation de la machine.
En aucune circonstance, régler le séparateur de papier lorsque la
machine est branchée.
AutoFold Pro
Page 6 FOLDING
Warning Labels
Do - be aware of any finger traps and rotating parts when operating
the machine.
Do - read this operator manual fully before operating the machine.
Do not - operate the machine with loose or trailing clothing.
Do not - operate the machine with loose hair.
Do - be aware of any finger traps and rotating parts when operating
the machine.
Do - be aware of sharp points and blades.
Do - be aware of rotating rollers.
Do - be aware of low current anti-static shock.
Attention au risque de se coincer les doigts, et aux pièces en
mouvement lors du fonctionnement de la machine.
Ne pas porter de vêtements flottants lors de l'utilisation de la machine
Rassembler les cheveux longs lors de l'utilisation de la machine.
Attention au risque de se coincer les doigts, et aux pièces en
mouvement lors du fonctionnement de la machine.
Attention aux éléments tranchants et aux couteaux.
Attention aux rouleaux en fonctionnement
Attention aux faibles chocs d'électricité statique
Lire ce mode d’emploi avant d’utiliser la machine.
Page 7
SYSTEM
DOCUMENT FOLDING MACHINE
Key to photograph below
1 Delivery assembly 2 Top Cover 3 Touchscreen
4 Gap Set Knobs 5 System Switch 6 Fuses
7 Mains Input Socket 8 Emergency Stop Switch
1
5
7
23
6
4
AutoFold Pro
AutoFold Pro
8
Page 8 FOLDING
ADJUSTING THE TILT OF THE FEED BED
FITTING THE TRANSFER BED ASSEMBLY TO THE AUTOCREASER AND
ALIGNING THE MACHINES.
1. The Feed Bed can be tilted, so that it matches the height of the creasing unit that is
being used with it.
(i) Open the front and rear column covers.
(ii) Loosen the knurled locking collar at the top of the front gas spring.
(iii) Adjust the tilt of the Feed Bed, (up or down) to match the height of the creasing
unit, then re-tighten both of the knurled locking collars.
1. The AutoFold is supplied, as standard, with a Transfer Bed Assembly that fits onto the
AutoCreaser 33 and AutoCreaser Pro 33 machines. A Transfer Bed Assembly that will
fit the wider AutoCreaser 50 and AutoCreaser Pro 50 machines can be purchased as
an optional extra (see accessories and options on page 37).
(i) Remove the stacker unit from the AutoCreaser and fit the Transfer Bed Assembly as
shown in FIG.8
(ii) Tilt the feed bed of the AutoFold, as described above, to align with the Transfer Bed
Assembly as shown in FIG.8
Knurled Locking Collar
Front Column Cover Rear Column Cover
Operating the AutoFold Pro
Page 9
SYSTEM
(iii) Adjust the relative positions of the machines so that the Transfer Bed Assembly aligns
with the Autofold Feed Bed as shown in FIG.9
(iv) Plug the connector, on the flying lead of the Transfer Bed Assembly, into the AutoFold
Socket as shown in FIG.9. This electrical connection between the AutoFold and the
AutoCreaser is a safety feature. If the system switch on the Autofold is switched off or
a jam occurs on the AutoFold the AutoCreaser will stop feeding.
When using the AutoFold with an AutoCreaser Pro 33 or an AutoCreaser Pro 50, it is
recommended that the AutoCreaser is set to Pulse Feed and the speed is set to number 2.
Depending on the type of crease and length of the paper, the speed setting may need to be
changed to speed number 1 or number 3.
NOTE.
(TOP VIEW)
FIG.9
AutoCreaser
Transfer Bed Assembly
Morgana
AutoCreaser Unit
AutoFold
Feed Bed
Align Machines
As Shown
Socket
AutoFold
AutoFold
Morgana
Feed Bed
AutoCreaser Unit
AutoCreaser
Transfer Bed Assembly
(FRONT VIEW)
FIG.8
Align Machines
As Shown
AutoFold Pro Operating the AutoFold Pro
TOUCHSCREEN OPERATION
1. Turn the Emergency Stop button clockwise to switch the power on. After the
system start up procedure the touch screen will be displayed as shown below.
WARNING:-
Wait at least 10 seconds, after making any selection on the Touchscreen
panel, before switching the machine OFF. Failure to do so could result in the
data storage being corrupted, and the machine not operating.
The touch screen is laid out into 3 main areas as shown below:
Page 10 FOLDING
Setting
page
Status of
machine &
data entry
area. Also
used for
quick links
to setting
pages.
Tabs to enable switching between setting
pages -choose either Paper Settings, Gap
settings, Feed Fan Setting, Fold settings,
Delivery settings, Store and Tools.
Operating the AutoFold Pro
IMPORTANT.
If you have not been trained to operate this machine, we strongly advise that you select
the red cross icon.
We recommend that you either seek training or ask a trained operator to run the machine
for you.
Select the green tick icon only if you have been trained to operate this machine.
If you have not been trained to operate this machine and you select the green tick icon,
Morgana Systems Ltd accept no responsibility for personal injury, damage to the
machine or damage to materials being processed by the machine.
Altri manuali per AutoFold Pro
1
Indice
Altri manuali Morgana Macchina piegatrice
Morgana
Morgana AutoFold Pro Manuale utente
Morgana
Morgana DIGIFOLD Manuale utente
Morgana
Morgana TF MEGA-S Manuale utente
Morgana
Morgana Digifold 5000P Manuale utente
Morgana
Morgana MB300 XL Pro Manuale utente
Morgana
Morgana UFO Manuale
Morgana
Morgana DigiFold Pro Manuale utente
Morgana
Morgana Digifold Pro CB Manuale utente
Morgana
Morgana DocuFold Pro Manuale utente
Morgana
Morgana Square fold 104 Manuale utente
