Morningstar RelayDriver Manuale utente
RELAYDRIVERTM
Logic Module Accessory
Installation and Operation Manual
…..
Four Channel Relay Driver
…..
1MORNINGSTAR CORPORATION
Table of Contents
1.0 Getting Started...........................................................3
1.1 What’s in the Box?..................................................................... 3
1.2 Features..................................................................................... 4
1.3 Factory Settings......................................................................... 5
2.0 PC Software Installation ...........................................6
2.1 System Requirements ............................................................... 6
2.2 Installing MSView.................................................................. 6
3.0 Configuration.............................................................9
3.1 Open the Setup Wizard ............................................................. 9
3.2 Assign Functions ..................................................................... 10
3.3 Programming the Relay Driver ................................................ 34
4.0 Mounting...................................................................40
4.1 Required Tools ........................................................................ 40
4.2 Wall Mounting.......................................................................... 41
4.3 DIN Rail Mounting.................................................................... 43
5.0 Wiring........................................................................45
5.1 Channel Wiring........................................................................ 45
5.2 Communications Wiring........................................................... 50
6.0 Operation..................................................................53
6.1 LED Indications........................................................................ 53
6.2 Protections............................................................................... 55
6.3 Maintenance............................................................................ 55
7.0 Troubleshooting FAQs............................................56
Appendix A – MS Product Variables ...........................59
Warranty .........................................................................61
Technical Specifications...............................................62
RELAY DRIVER 2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS:
This manual contains important safety, installation and operating
instructions for the Morningstar Relay Driver.
The following symbols are used throughout this manual to indicate
potentially dangerous conditions or important safety instructions.
WARNING: Indicates a potentially dangerous ondition.
Use extreme caution when performing this task.
CAUTION: Indicates a critical procedure for safe and
proper operation of the Relay Driver.
NOTE: Indicates a procedure or function that is
important to the safe and proper operation of the
Relay Driver.
General Safety Information
Read all the instructions and cautions in the manual before
starting the installation.
There are no user serviceable parts in the Relay Driver. Do not
disassemble or attempt to repair.
Ensure that battery power has been disconnected before
installing or removing the Relay Driver.
Do not allow water to enter the Relay Driver.
3MORNINGSTAR CORPORATION
1.0 Getting Started
1.1 What’s in the Box?
Relay Driver
Software CD
Operator’s Manual
Serial RS-232 Cable (6ft)
Meter Bus RJ-11 cable (4ft)
Four (4) Mounting Screws
Mounting Template
RELAY DRIVER 4
1.2 Features
Figure 1. Features of the Relay Driver
Channel Terminal Block
Provides connections for:
Relay Driver power and ground
Four (4) Channel connections (relay contacts, input
voltages, output signals, etc)
DIN Rail Release Tab
Snap on / Release from DIN rail.
LED Indicators
Displays power and channel status, faults, sampling interval.
Meter Bus Ports
Connects to other Morningstar products with meter bus
communications. Two ports (in/out) allow a daisy-chain
connection of multiple devices.
Serial RS-232 Port
A serial programming port used to establish a connection
between the Relay Driver and a PC.
5MORNINGSTAR CORPORATION
1.3 Factory Settings
The Relay Driver is pre-configured at the factory with a default
configuration as outlined below. If a different configuration is
needed, a custom configuration will need to be programmed
into the Relay Driver.
Sections 2.0 through 5.0 explain software installation, custom
configuration, and installation.
Channel 1
Threshold Function:
Channel OFF when Vbattery < 11.5V
Channel ON when Vbattery > 12.6V
1 minute delay before turning on/off
Channel 2
Threshold Function:
Channel OFF when Vbattery < 11.1V
Channel ON when Vbattery > 12.2V
1 minute delay before turning on/off
Channel 3
Threshold Function:
Channel OFF when Vbattery < 14.0V
Channel ON when Vbattery > 15.0V
Channel 4
TriStar Alarm/Fault Monitor:
Channel OFF when no alarms/faults exist
Channel ON when any alarms/faults exist
Excludes RTS open alarm
No communication timeout alarm
RELAY DRIVER 6
2.0 PC Software Installation
2.1 System Requirements
NOTE: Morningstar provides software for Windows®
PCs only. Other platforms are not supported.
• Intel® 486 or Pentium® processor
• Microsoft® Windows 95, 98, 2000, Windows XP Professional
or Home Edition
• 32MB of RAM (64MB Recommended)
• CD-ROM drive (If installing by CD)
• Up to 1.5MB of available hard-disk space
• Internet connection and service (If downloading from web)
• Web browser (If downloading from web)
2.2 Installing MSView
NOTE: The software CD provided may not contain the
latest version of MSView. Check our website for
updates at:
http://www.morningstarcorp.com/products/software
Morningstar MSView is an all-inclusive software package that
provides programming, graphing, and logging capabilities for
supported Morningstar products. MSView is also used to
configure and program the Relay Driver.
7MORNINGSTAR CORPORATION
This section details two software installation options. The first
option explains how to install MSView from the included
software CD. The second option explains how to download and
install the latest version of MSView from our website. We
recommend downloading the latest version from our website if
possible. It is possible to update to a newer version of MSView
at a later time.
Option #1: Install MSView from the included CD
Step 1
Insert the MSView Setup CD in the PC CD-drive. After a few
moments, the MSView software setup wizard should appear.
If setup does not begin (or the autorun CD-drive feature has
been disabled), run Setup.exe on the CD drive using Windows
Explorer.
Step 2
Follow the wizard instructions to install MSView software.
Step 3
After the install is complete, remove the CD from the drive and
store the MSView setup CD in a safe place.
- OR -
Option #2: Download and install MSView software
from the web
Step 1
Visit: http://www.morningstarcorp.com/products/software
9MORNINGSTAR CORPORATION
3.0 Configuration
The MSView software includes a Relay Driver setup wizard to
create and save configurations. Configurations can then be
programmed into the Relay Driver so that it functions as
required.
3.1 Open the Setup Wizard
1. Click the Windows Start Menu button
2. Under Programs, find the MSView Folder.
3. Click the Relay Driver Wizard program Icon
Figure 2. Relay Driver Setup Screen
The Relay Driver Setup screen should appear (see Fig. 2). The
setup wizard is now open. Proceed to section 3.2.
Indice
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
