Morphy Richards 73281 Manuale utente

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Bagless upright vacuum cleaner

Please read and keep these instructions

VC73281 MUK Rev 1

For replacement parts, help with using your Morphy Richards, problems

and lots more, contact us by phone or through our website.

UUKKHHeellpplliinnee::0088444488771100994499

RReeppllaacceemmeennttPPaarrttss::0088444488773300771155

IIrreellaannddHHeellpplliinnee::11880000440099111199

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

Dust canister

It is important to regularly empty the canister, even if it does not appear full.

Filters

It is important that the dust canister pleated/mesh filter is tapped clean over a

dustbin each time the dust canister is emptied, this allows air through the appliance.

Wash the canister filters regularly in luke-warm water and allow to air dry before

re-fitting.

Blockages

Check the hose, tubes and tools for blockages.

Safety cut-out

If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may operate.

If this happens, switch off and disconnect from the mains supply. Clear any blockage,

empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

If the brush-bar is not rotating, check the belt (as described on page 6). Replace any

damaged or broken belts.

73281 rev1 13/3/08 16:22 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following common sense

safety rules.

Please read these

instructions carefully before

using the product.

Primarily there is danger of

injury or death and secondly

the danger of damage to the

appliance.

Location

• Do not use or keep this

product outside.

• Do not store the appliance

near hot surfaces eg. ovens

or heating appliances.

Mains lead

• Do not allow the mains lead

to become strained or run

this appliance over it.

• If the electrical cable

becomes damaged, the

cable assembly must be

replaced. Do not attempt this

task yourself, contact the

helpline number that is found

at the bottom of the page.

Personal safety

• WARNING: Keep loose

clothing, hair, fingers etc.

away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• WARNING: Only lift the

product by the handle

⁄

• Disconnect from the

mains supply before

attempting to clear

blockages, clear the

brush or replace the belt.

• Disconnect from the mains

supply before cleaning or

emptying the appliance.

• Never modify the cleaner in

any way.

• Never use in the presence of

explosive liquid or vapours.

• Never pick up inflammable or

poisonous liquids such as

petrol, copier toner or other

volatile substances. Never

pick up acids, asbestos or

asbestos dust.

• Never touch the plug or

cable with wet hands.

• Unprofessional repairs can

be dangerous for users.

• Use only Morphy Richards

spare parts and accessories.

• The appliance must never be

left running unsupervised.

• This appliance is intended for

domestic use only. Misuse or

use for commercial or any

other purpose will render the

guarantee invalid.

• Always disconnect the

appliance from the mains

supply after use.

• This appliance is not

intended for use by persons

(including children) with

reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge,

unless they have been given

supervision or instruction

concerning use of the

appliance by a person

responsible for their safety.

• To protect against fire,

electric shock and personal

injury, do not immerse cord,

plug or cleaner in water or

other liquid.

Product safety

• Never use the appliance

without the filters being

installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

• Never over-extend the hose

such that the cleaner is

pulled over. If the cleaner is

knocked over, switch off

before attempting to upright.

• Never pick the cleaner up by

the floor nozzle when

connected to the mains, use

the carrying handle.

Children

• Children do not understand

the dangers associated with

operating electrical

appliances. Never allow

children to use this

appliance.

• Children should be

supervised to ensure that

they do not play with the

appliance, or stumble over

the power cord.

Electrical

requirements

Check that the voltage on the

rating plate of your appliance

corresponds with your house

electricity supply which must

be A.C. (Alternating current).

If the socket outlets in your

home are not suitable for the

plug supplied with this

appliance, the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the mains

lead, if severed, must be

destroyed, as a plug with

a bared flexible cord is

hazardous if engaged

into a live socket outlet.

Should the fuse in the 13

amp plug require changing, a

13 amp BS1362 fuse must

be fitted.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

73281 rev1 13/3/08 16:22 Page 2

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

FEATURES

⁄Handle

¤Handle locking pin

‹Metal telescopic tube

›Stretch hose

ﬁDust canister lid

ﬂFilter assembly

‡Dust canister

·Floor nozzle height

adjustment dial

‚Turbo tool

(certain models only)

„Upholstery tool /

dusting brush

‰Crevice tool

ÂHose clip (unassembled),

including hose clip screw

ÊDust canister release

button

ÁHandle height adjuster

button

ËCord storage cleats

ÈPower cord

ÍHose clip (assembled)

ÎTelescopic tube release

button

ÏHose hook

ÌUpright release pedal

ÓON/OFF button

⁄

‹

ﬂ

‡

ﬁ

›

„

‰

‚

73281 rev1 13/3/08 16:22 Page 3

OPERATING THE

APPLIANCE

Assembly

WARNING: Do not plug in

the cleaner until it is

assembled.

1Carefully unpack all of the

components.

2Lift the cleaner body to the

upright position.

3Slide the telescopic tube ‹into

the opening on the top of the

unit. Ensure the telescopic tube

fits in correctly, and is locked

into place A.

• To remove the telescopic tube,

press the release button Î,

located on the rear of the

vacuum cleaner, then lift the

telescopic tube up B.

4Slide the handle ⁄into the top

of the telescopic tube. Ensure

the handle locking pin ¤fits in

place C.

• Remove the handle by pressing

the locking pin, then pulling the

handle up.

5To increase the height of the

handle, push downward on the

handle height adjuster button Á

and raise the handle to the

desired height. With the handle

at the desired height, release the

button, the handle will click

securely into place.

Hose clip fitting D

1Using a cross-head screwdriver,

remove the hose clip screw from

the rear of the product.

2Insert the hose clip Âinto it’s

slot in the rear of the appliance.

3Re-fit the screw and tighten. Do

not overtighten.

Hose

Locate the hose under the hook

and into the hose clip.

WARNING: Do not overstretch

the hose, otherwise there is a

risk of the product being

pulled over.

Cord Storage

This appliance features

convenient cord storage. Wind

the power cord È around the

two cord holder cleats Ëon the

side of the unit. Turn the upper

cord cleat to the left or right to

quickly release the power cord.

USING

Unwind the power cord fully.

Plug the cord into the supply

mains. Press the ON/OFF

button Ó to turn the vacuum

cleaner on and off.

Release the handle by pushing

the upright release pedal Ì.

This allows repositioning of the

handle for storage, normal

operation or cleaning beneath

furniture E.

Floor nozzle

height adjustment

Before using the cleaner, the

floor nozzle height must be set

to the correct height.

Choose the setting which most

closely matches your carpet

height, using the floor nozzle

height adjustment dial ·. This

raises and lowers the brushbar

to suit your carpet type.

When the cleaner is in it’s

upright position, or when using

the hose › and tools ‚ „ ‰,

ensure the floor nozzle height

adjustment dial is at the tools

setting.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

73281 rev1 13/3/08 16:22 Page 4

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Using on carpets

1Place the cleaner in it’s upright

position.

2Set the carpet height

adjustment dial · to the

desired position.

3Release the mains cable by

revolving the quick release cleat

half-a-turn and extend the cable

fully.

4Plug the cable into the mains

socket.

5Step on the handle release

pedal to release the handle to

the desired position.

6Press the ON/OFF button to the

‘ON’ position.

IMPORTANT: To prevent damage

to carpets:

• Never leave the cleaner

switched on in one place for an

extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

• Never lean on the product.

Using the

attachments

Follow steps 1-4of the ‘Using

on carpets’ section, but set the

carpet height adjustment dial to

the tools setting.

5Attach the accessories ‚ „ ‰

to the handle, removing the

handle from the telescopic tube,

then firmly push in the desired

accessory F:

Turbo tool ‚ is ideal for pet

hair removal from stairs and

upholstery.

Upholstery tool „ for

upholstery, stairs etc.

Dusting brush „ for delicate

surfaces.

Crevice tool ‰for awkward

places, corners and behind

radiators etc.

6If additional length is required,

remove the telescopic tube from

the cleaner, connect it to the

handle, and add the desired

accessory to the end of the tube

7Switch ON/OFF.

• IMPORTANT: When using the

hose and tools, locate the hose

into the hose hook Ï on the

main unit. This will help prevent

the cleaner from tipping over.

• IMPORTANT: Turning the cleaner

sideways helps prevent the

cleaner being pulled along by

the stretched hose.

Using & cleaning the

turbo nozzle

Attach the Turbo nozzle to either

the handle or the telescopic

tube as described previously.

Following use, your turbo nozzle

may become clogged. Switch

the cleaner to ‘OFF’. Turn over

the tool and pull away any hairs

or fibres. If they are tightly

wound around the brush,

carefully snip the fibres with

scissors, being careful not to

damage the brush bar, pull away

from the brush bar and dispose.

SAFETY CUT-OUT

If the cleaner overheats, a motor

protection thermostat will

automatically switch the motor

off. If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least

60 minutes. Check the airways

for blockages, empty the dust

canister and clean the filters

before restarting.

73281 rev1 13/3/08 16:22 Page 5

EMPTYING THE

DUST CANISTER

Empty the dust canister

‡

regularly even if it does not look

full, this will maintain the

performance.

1Unplug the cleaner from the

mains switch.

2Press the dust canister release

button

and pull the canister

away from the main body H.

3Take the canister to a dustbin.

4Hold the dust canister over the

dustbin. Press the empty release

button

on the back of the

canister. This opens the door



at the base of the canister for the

contents to be emptied-out I.

REMOVING AND

CLEANING THE

FILTERS

HEPA filter

IMPORTANT: After every empty,

clean the dust canister filter

ﬂ

1Empty the dust canister.

2Remove the dust canister lid

ﬁ

by turning it counter-clockwise,

then lifting off J.

3Lift the filter assembly out of the

dust canister K.

4Lift out the mesh filter from the

filter frame by twisting it counter-

clockwise L.

5Tap the filter over a dustbin until

no more dust falls out M.

6You may also wash the filter in

luke-warm water, do not use

detergents. It is recommended to

wash the filter once a month or

when suction seems reduced.

Leave the filter to thoroughly air

dry before refitting into the

vacuum.

NOTE: The white material in the

filter will become discoloured

over time, this is normal and will

not affect the filter’s

performance.

IMPORTANT: Always empty the

dust canister and clean the filter

and mesh following prolonged

use. Never overfill the dust

canister. Clean the filter and

mesh screen every time the dust

canister is emptied.

Motor protection filter

The motor protection filter

located underneath the dust

canister in the air-inlet pipe.

1Remove the dust canister.

2Lift out the filter N and shake

over a dustbin.

The filter may also be washed in

water (no detergents). Allow the

filter to air dry. Ensure the filter is

thoroughly dry before refitting.

3Replace the filter.

Exhaust filter

The exhaust filter

is located

below the dust canister

compartment.

1Remove the dust canister.

2Remove the exhaust filter by

twisting the motor protection

filter cover

and lifting it away

3Lift the filter out and shake

vigorously over a dustbin. The

filter may also be washed in luke

warm water. Do not use

detergents. The filter must be

completely dry before re-fitting.

Allow filters to air dry naturally.

4Replace the filter and the dust

canister.

CHANGING THE

BELT

If the brush bar

stops

rotating, it is likely that the drive

belt

has snapped (usually

because the brush has been

stalled). Replace the belt with the

spare belt provided. Additional

belts can be obtained from

Morphy Richards by calling the

helpline number at the base of

the page.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199



73281 rev1 13/3/08 16:22 Page 6

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Accessing the floor

nozzle

1Disconnect the cleaner from the

mains supply.

2Press the handle release pedal

and place the cleaner face down

on a soft surface, eg. carpet.

3Remove the four screws holding

the two undercarriage plates

in position. Remove the plates P.

4Lift up the undercarriage

and

unclip from it’s location

5Underneath the undercarriage is

the height adjustment cam. In the

centre of the cam is a screw,

remove this screw

6Next, remove the four remaining

floor nozzle screws

, two

located by the rear wheels and

two halfway along the floor nozzle

7Turn the product over and pull off

the height adjustment knob.

8Lift the rear of the floor nozzle

cover and unclip from the front.

Put safely to one side

Removing and

re-fitting the rotating

brush bar & belt

1Lift out the belt cover

˘ U

2Gently lever out the right hand

side of the brush-bar, followed by

the left hand side

3To re-fit, thread the brush-bar

through the belt. Place the left

hand side of the brush-bar into

location, then place the belt

around the motor shaft. Pull the

brush-bar forwards (stretching the

belt) and locate the right hand

side of the brush-bar.

4IMPORTANT: Make sure both

ends of the brush-bar are fully

and correctly located, and the

belt is not trapped. The

brush-bar should be able to be

rotated by hand.

5Re-fit the belt cover carefully,

noting it’s location.

Refitting the floor

nozzle cover

1Hook the front of the cover into

the floor nozzle, then lower the

rear of the cover. Note: it may be

necessary to lift the upright

portion of the product to allow

the cover to fully close.

2Refit the four main screws.

3Turn the product over and check

that the front of the cover is fully

closed.

4Insert the height adjustment

knob, carefully turning it until it

locates into the mating keyway

on the cam.

5Turn the product back over and

locate the screw into the centre

of the cam and tighten.

6Clip the undercarriage into

location and close into position.

7Re-fit the two undercarriage

plates and tighten the four

screws.

Return the cleaner to the upright

position. Connect to the mains

supply and switch on to test.

HELPLINE

If you have any difficulty with your

appliance, do not hesitate to call

us.

We are more likely to be able to

help than the store from where

you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

rear of the appliance.

• Serial number as shown on the

rating label.

UK Helpline 0844 871 0949

Replacement Parts 0844 873 0715

Ireland Helpline 1800 409 119

73281 rev1 13/3/08 16:22 Page 7

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company therefore reserves the right to change the specification of

its models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helplines (office hours)

UK 0844 871 0949

Spare Parts 0844 873 0715

Republic of Ireland 1800 409 119

VC73281 MUK Rev 1 03/08

FFoorrddeettaaiillssooffootthheerrpprroodduuccttssiinntthheeMMoorrpphhyyRRiicchhaarrddssrraannggee,,pplleeaasseesseeeeoouurrwweebbssiittee......

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailer’s receipt as proof of

purchase. Staple your

receipt to this back cover

for future reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase, it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after

28 days and within 24

months of original

purchase, you should

contact the helpline

number quoting model

number and serial number

on the product, or write to

Morphy Richards at the

address shown.You will be

asked to return the product

(in secure, adequate

packaging) along with a

copy of proof of purchase.

Subject to the exclusions

set out below (see

Exclusions), the faulty

appliance will then be

repaired or replaced and

dispatched usually within

seven working days of

receipt.

If, for any reason, this item

is replaced during the 2-

year guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore, it is vital to retain

your original receipt or

invoice to indicate the date

of initial purchase.

To qualify for the two-year

guarantee, the appliance

must have been used

according to the

manufacturer’s

instructions. For example,

the filters must have been

regularly cleaned as

instructed.

Morphy Richards shall not

be liable to replace or

repair the goods under the

terms of the Guarantee

where:

EXCLUSIONS

1The fault has been caused

or is attributable to

accidental use, mis-use,

negligent use or used

contrary to the

manufacturer’s

recommendations or where

the fault has been caused

by power surges or

damage caused in transit.

2The appliance has been

used on a voltage supply

other than that stamped on

the products.

3Repairs have been

attempted by persons

other than our service staff

(or authorised dealer).

4The appliance has been

used for hire purposes or

non-domestic use.

5The appliance is second

hand.

6Morphy Richards are not

liable to carry out any type

of servicing work under the

guarantee.

7Consumables such as the

filters and belt are not

covered by the guarantee.

• This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for

consequential loss or

damage. This guarantee is

offered as an additional

benefit and does not affect

your statutory rights as a

consumer.

• This guarantee is valid in

the UK and Ireland only.

For electrical products sold within the

European Community. At the end of the

electrical products useful life it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

73281 rev1 13/3/08 16:22 Page 8

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Morphy Richards Aspirapolvere

Morphy Richards

Morphy Richards IB73105 Manuale utente

Morphy Richards

Morphy Richards IB71050 Manuale utente

Morphy Richards

Morphy Richards Pod vacuum cleaner Manuale utente

Morphy Richards

Morphy Richards STORM LIGHT UPRIGHT VACUUM CLEANER - REV 3 Manuale utente

Morphy Richards

Morphy Richards Storm pets cylinder vacuum cleaner Manuale utente

Morphy Richards

Morphy Richards Orb vacuum cleaner Manuale utente

Morphy Richards

Morphy Richards Bagless Cylinder Vacuum Cleaner Manuale utente

Morphy Richards

Morphy Richards Storm Manuale utente

Morphy Richards

Morphy Richards ECO PRIUS Manuale utente

Morphy Richards

Morphy Richards IB70045 Manuale utente

Morphy Richards

Morphy Richards PremAir Cyclonic 70035 Manuale utente

Morphy Richards

Morphy Richards Supervac Deluxe Manuale utente

Morphy Richards

Morphy Richards BAGLESS UPRIGHT VACUUM CLEANER - REV 1 Manuale utente

Morphy Richards

Morphy Richards PerformAir Upright Vacuum Manuale utente

Morphy Richards

Morphy Richards Upright and Handheld Steam Cleaner Manuale utente

Morphy Richards

Morphy Richards Essentials Family and Pets+ Manuale utente

Morphy Richards

Morphy Richards PERFORMAIR CYCLONIC VACUUM CLEANER Manuale utente

Morphy Richards

Morphy Richards VC73410 MUK Manuale utente

Morphy Richards

Morphy Richards IB73370 Manuale utente

Morphy Richards

Morphy Richards ORB Pets Cyclone Manuale utente

Morphy Richards

Morphy Richards Goblin 73276 Manuale utente

Morphy Richards

Morphy Richards ULTRALIGHT CYCLONE VACUUM CLEANER Manuale utente

Morphy Richards

Morphy Richards ESSENTIALS COMPACT BAGLESS VACUUM CLEANER Manuale utente

Morphy Richards

Morphy Richards BAGLESS CYLINDER VACUUM CLEANER - REV 2 Manuale utente

Manuali Aspirapolvere popolari di altre marche

Bissell

Bissell LittleGreen Proheat 1425 Series Manuale utente

Panasonic

Panasonic MC-YL637S147-AE Manuale utente

NEFF

NEFF N17XH10 0 Series Manuale utente

LG A9 Series Manuale utente

Oreck

Oreck Cordless Captura BK51700 Series Manuale utente

Kogan

Kogan KAVACROBVWA Manuale utente

Kränzle

Kränzle VENTOS 50 ID Guida utente

EVVO

EVVO Ai35 Manuale utente

DeWalt

DeWalt DWH200D Manuale utente

Pontec

Pontec Pondomatic Vacuum Cleaner Manuale utente

Cleanmaxx

Cleanmaxx PC-P007E Manuale utente

Exido

Exido 240-114 Manuale utente

RIDGID

RIDGID WD1685AU0 Manuale utente

Ezviz

Ezviz RE4P Manuale utente

STG global

STG global TANVAC HDV3000 Manuale utente

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuale utente

Factory

Factory M3340 Manuale utente

Shop-Vac

Shop-Vac VN92 SERIES Manuale utente