Moxa Technologies AWK-3252A Series Manuale utente

P/N: 1802032520010

*1802032520010*

AWK-3252A Series

Quick Installation Guide

Moxa AirWorks

Version 1.0, December 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The AWK-3252A Series is an industrial-grade AP/bridge/client with IEEE

802.11ac Wave 2 technology. This Series features concurrent dual-band

Wi-Fi data transmissions up to 400 Mbps (2.4 GHz mode) and 867 Mbps

(5 GHz mode) simultaneously, meeting the speed and flexibility

requirements for industrial applications. In addition, the built-in dual

band pass filter and the wide-temperature design ensure the reliability

and continuous operation in harsh environments. The dual redundant

DC power inputs enhance availability while PoE support provides more

flexibility for powering end devices and simplifying field-site

deployments. Meanwhile, backwards compatibility with 802.11a/b/g/n

makes the AWK-3252A the ideal solution for constructing a versatile

wireless data transmission system.

- 3 -

Panel Layout of the AWK-3252A

1. Grounding screw (M5)

2. Terminal blocks for PWR1,

PWR2, relay, DI 1 and DI 2

3. Reset button

4. Antenna connector A

5. System LEDs: PWR1, PWR2,

PoE, 2.4GHz, 5GHz, SYSTEM

6. USB host (type A for ABC-02)

7. Console port (RS-232, RJ45)

8. LAN1 (PoE), LAN 2 ports

(10/100/1000BaseT(X) ports,

RJ45)

9. Antenna connector B

10. Model name

11.

Screw holes for wall-

mounting

kit

12.

DIN-rail mounting kit

13.

Cable holder screw

- 4 -

Mounting Dimensions

DIN-Rail Mounting

When shipped, the metal DIN-rail mounting kit is fixed to the back

panel of the AWK-3252A. Mount the AWK-3252A on to a corrosion-free

mounting rail that adheres to the EN 60715 standard.

STEP 1:

Insert the upper lip of the DIN

-rail

kit into the

mounting rail.

STEP 2:

Press the

AWK-3252A towards the

mounting rail until it snaps into

place.

- 5 -

To remove the AWK-3252A from the DIN rail, do the following:

STEP 1:

Pull down the latch on the DIN

rail kit with a screwdriver.

STEP 2 & 3:

Slightly pull the

AWK-3252A

forward and lift it up to remove

it from the mounting rail.

Wall Mounting (Optional)

For some applications, it may be more convenient to mount the AWK-

3252A to a wall, as illustrated below.

STEP 1:

Remove the aluminum DIN-

rail attachment plate from

the

AWK-3252A, and then

attach the wall

-mounting

plates with M3 screws, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the

AWK-3252A to a wall requires 3 screws.

Use

the AWK-3252A device, with wall-mounting plates

attached, as a guide to mark the correct locations of

the 3 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the

shafts should be less

than 3.5 mm in diameter, as shown in the figure on the

right.

Do not drive the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall-mounting panel between the wall and

the screws.

NOTE

Test the screw head and shank size by inserting the screws

into

one of the keyhole shaped apertures of the w

all-mounting

plates before they are fixed to the wall.

- 6 -

STEP 3:

Once the screws are fixed into the

wall, insert the four screw heads

through the large opening of the

keyhole

-shaped apertures, and then

slide the

AWK-3252A downwards, as

indicated to the ri

ght. Tighten the

three screws for added stability.

WARNING

•

This equipment is intended to be used in a Restricted

Access Location, such as a dedicated computer room

where

only authorized service personnel or

users can gain access.

Such personnel must be instructed about the fact that the

metal chassis of the equipment is extremely hot and may

cause burns.

•

Service personnel or users have to pay special attention

and take special precautions before handling this

equipment.

•

Only authorized, well-trained professionals should be

allowed to access the restricted access location. Access

should be controlled by the authority responsible for the

location with lock and key or a security identity system.

•

External metal parts are hot!! Pay special attention or

use special protection before handling the equipment.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

AWK-3252A.

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes that dictate the

maximum current allowed for each wire size. If the

current

goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

Read and Follow These Guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the crossing point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire co

nduit. To avoid interference, wires with

different signal characteristics should be routed separately.

- 7 -

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•For future reference, you should label the wiring used for all of your

devices.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked “Class 2” or “LPS” and rated O/P: 22 W

ATTENTION

Make sure

the external power adapter (includes power cords

and plug assemblies) provided with the unit is certified and

suitable for use in your country.

ATTENTION

DO NOT

use a PoE Injector. Instead, use an IEEE 802.3af or

IEEE 802.3at compliant PSE (Power Sourcing Equipment) for

PoE (Power over Ethernet) devices.

Grounding the AWK-3252A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface,

such as a metal panel. The potential

difference between any two

grounding points must be zero. If

the potential difference is NOT zero, the product could be

permanently damaged.

Installations with Cable Extended Antennas for Outdoor

Applications

If an AWK device or its antenna is installed in an outdoor location,

proper lightning protection is required to prevent direct lightning strikes

to the AWK device. In order to prevent the effects of coupling currents

from nearby lightning strikes, a lightning arrester should be installed as

part of your antenna system. Ground the device, antenna, as well as

the arrester properly to provide maximum outdoor protection for the

device.

- 8 -

Arrester Accessories

•SA-NMNF-02: Surge arrester, N-type (male) to N-type (female)

•SA-NFNF-02: Surge arrester, N-type (female) to N-type (female)

Terminal Block Pin Assignment

The AWK-3252A comes with a 10-pin terminal block located on the top

panel of the device. The terminal block contains dual power inputs, a

relay output, and dual digital inputs. Refer to the following figure and

table for the detailed pin assignment.

Definition

DC Power Input 1

DC Power Input 2

Relay Output

Digital Input 1

Digital Input GND

Digital Input 2

Digital Input GND

Wiring the Redundant Power Inputs

The top two pairs of contacts of the 10-contact terminal block

connector on the AWK-3252A’s top panel are used for the AWK-3252A’s

two DC inputs. The top view of the terminal block connector is shown

below.

- 9 -

STEP 1: Insert the negative/positive DC wires

into the

+/- terminals.

STEP

2: Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the AWK-3252A’s

op panel.

NOTE

Input Terminal Block (CN1) is suitable for wire size range of 16-

28 AWG (1.318-0.0804 mm²).

ATTENTION

If the

AWK-3252A

is connected to a motor or other similar type

of equipment, be sure to use power isolation protection. Before

connecting the

AWK-3252A to the DC power inputs, make sure

the DC power source voltage is stable.

Wiring the Relay Contact

The AWK-3252A has one relay output, which consists of the two

contacts of the terminal block on the AWK-3252A’s top panel. Refer to

the previous section for detailed instructions on how to connect the

wires to the terminal block connector, and how to attach the terminal

block connector to the terminal block receptor. These relay contacts are

used to indicate user-configured events. The two wires attached to the

Relay contacts form an open circuit when a user-configured event is

triggered. If a user-configured event does not occur, the Relay circuit

will be closed.

Wiring the Digital Inputs

The AWK-3252A has two sets of digital inputs—DI1 and DI2. Each DI

comprises two contacts of the 10-pin terminal block connector on the

AWK-3252A’s top panel. Refer to the “Wiring the Redundant Power

Inputs” section for detailed instructions on how to connect the wires to

the terminal block connector, and how to attach the terminal block

connector to the terminal block receptor.

Cable Holder Installation

Attach the cable holder to the bottom of the AWK-3252A to keep

cabling neat and avoid accidents that result from untidy cables.

- 10 -

STEP 1: Screw the cable holder onto the bottom

of the

AWK-3252A.

STEP 2:

After mounting the AWK-3252A

and plugging in the LAN cable,

tighten the cable along the device and wall.

Communication Connections

10/100/1000BaseT(X) Ethernet Port Connection

The 10/100/1000BaseT(X) ports located on the AWK-3252A’s front

panel are used to connect to Ethernet-enabled devices.

MDI/MDI-X Port Pinouts

1000BaseT

MDI/MDI-X

10/100BaseT

(X)

MDI

10/100BaseT

(X)

MDI-X

TRD(0)+

TX+

RX+

TRD(0)–

TX-

RX-

TRD(1)+

RX+

TX+

TRD(2)+

TRD(2)-

TRD(1)-

RX-

TX-

TRD(3)+

TRD(3)-

RS-232 Connection

The AWK-3252A has one RS-232 (8-pin RJ45) console port located on

the front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to

connect the AWK-3252A’s console port to your PC’s COM port. You may

then use a console terminal program to access the AWK-3252A for

console configuration.

Altri manuali per AWK-3252A Series

Indice

Altri manuali Moxa Technologies Unità di controllo

Moxa Technologies

Moxa Technologies PWR-190-AC/DC Manuale utente

Moxa Technologies

Moxa Technologies CB-108 Manuale utente

Moxa Technologies

Moxa Technologies NE-4100 Series Manuale utente

Moxa Technologies

Moxa Technologies WAPN001 Manuale utente

Moxa Technologies

Moxa Technologies WFS001 Manuale utente

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Manuale utente

Moxa Technologies

Moxa Technologies NPort Z2150 Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Manuale utente

Moxa Technologies

Moxa Technologies CA Series Manuale utente

Moxa Technologies

Moxa Technologies EOM-104 Series Manuale utente

Moxa Technologies

Moxa Technologies TCC-100 Series Manuale utente

Moxa Technologies

Moxa Technologies ioThinx 4500 45ML-5401 Manuale utente

Moxa Technologies

Moxa Technologies MGate 4101-MB-PBS Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort E Series Manuale utente

Moxa Technologies

Moxa Technologies DA-IRIGB-4DIO-PCI104-EMC4 Manuale utente

Moxa Technologies

Moxa Technologies CA-134I Manuale utente

Moxa Technologies

Moxa Technologies WAPN008 Manuale utente

Moxa Technologies

Moxa Technologies ABC-01 Manuale utente

Moxa Technologies

Moxa Technologies CA-132 series Manuale utente

Moxa Technologies

Moxa Technologies CA Series Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort E1 Series Manuale utente

Moxa Technologies

Moxa Technologies PWR-100 Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente