Moxa Technologies AWK-1121 Manuale utente

Reproduction without permission is prohibited.

P/N: 1802011210011

AWK-1121

Quick Installation Guide

Moxa AirWorks

Second Edition, June 2014

- 2 -

Overview

Moxa’s AWK-1121 WLAN Client is ideal for applications that are hard to

wire, too expensive to wire, or use mobile equipment that connects over

a TCP/IP network. The AWK-1121 is rated to operate at temperatures

ranging from 0 to 60°C for standard models and -40 to 75°C for extended

temperature models, and is rugged enough for any harsh industrial

environment. Installation is easy, with either DIN-Rail mounting or

distribution boxes. The DIN-Rail mounting ability, wide operating

temperature range, and IP30 housing with LED indicators make the

AWK-1121 a convenient yet reliable solution for any industrial wireless

application.

Package Checklist

Moxa’s AWK-1121 is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

•1 AWK-1121

•1 Swivel-type Antenna (2dBi, RP-SMA, 2.4&5GHz)

•1 Quick Installation Guide

•1 Document and software CD

•1 Moxa Product Warranty Booklet

•1 Protective Cap

•1 Resistive Terminator

- 3 -

Panel Layout of the AWK-1121

Top Panel View

Front Panel View

Rear Panel View

1. Grounding screw (M3)

2. Terminal block for PWR1 and

PWR2

3. RS-232 console port

4. AUX antenna port

5. System LEDs:

PWR, FAULT, and

STATE LEDs

6. LEDs for signal strength

7. WLAN and LAN LEDs

8. 10/100BaseT(X) RJ45 Port

9. MAIN antenna port

10.

Screw hole for wall mounting kit

11.

DIN-Rail mounting kit

12.

Reset button

- 4 -

Mounting Dimensions

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back

panel of the AWK-1121 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the AWK-1121, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove the AWK-1121 from the DIN-Rail, simply reverse Steps 1 and

- 5 -

Wall Mounting (optional)

For some applications, it may be more convenient to mount the

AWK-1121 to a wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from the

AWK-1121, and

then attach the

wall mount

plates with M3 screws, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the

AWK-1121 to a wall requires 4 screws.

Use the

AWK-1121 device, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads

of the screws should be less

than 6.0 mm in diameter, and the

shafts should be less

than 3.5 mm in diameter, as shown in the figure at the

right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into

the wall, insert the four screw

heads through the large opening

of the keyhole

-shaped

apertures, and then slide the

AWK

-1121 downwards, as

indicated to the right. Tighten

the four screws for added

stability.

- 6 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa AWK-1121.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowed for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked

“Class 2” or “LPS” and rated O/P: 12 to 48 VDC

, minimum

7.7 W (12 V/0.55 A to 48V/0.16 A), 25°C.

ATTENTION

Make sure

the external power adapto

r (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

- 7 -

Grounding the Moxa AWK-1121

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

The 4-contact terminal block connector on the AWK-1121’s top panel is

used for the AWK-1121’s two DC inputs. The top and front views of the

terminal block connector are shown here.

Top View

Front View

STEP 1:

Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

-blade screwdriver to

tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the AWK-1121’s t

panel.

ATTENT

ION

Before connecting the

AWK-1121

to the DC power inputs, make

sure the DC power source voltage is stable.

- 8 -

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the AWK-1121’s front panel are

used to connect to Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

RS-232 Connection

The AWK-1121 has one RS-232 (8-pin RJ45) console port located on the

top panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect

the Moxa AWK-1121’s console port to your PC’s COM port. You may then

use a console terminal program to access the AWK-1121 for console

configuration.

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

-----

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

-----

NOTE

The pin numbers for male DB9 and DB25 connectors, and

hole numbers for female DB9 and DB25 connectors are

labeled on the connector. However, the numbers are

typically quite small, so you may need to use a magnifying

glass to see the numbers clearly.

2. The pin numbers for both 8-pin and 10-p

in RJ45 connectors

(and ports) are typically not labeled on the connector (or

port). Refer to the Pinout diagram above to see how RJ45

pins are numbered.

- 9 -

LED Indicators

The front panel of the Moxa AWK-1121 contains several LED indicators.

The function of each LED is described in the table below.

LED

Color

State

Description

PWR Green

Power is being supplied

Off

Power is not being supplied

FAULT Red

Booting

Blinking

(slow)

IP address cannot be got from DHCP

server (interval: 1 sec).

Blinking

(fast)

IP address conflict (interval: 0.5 sec).

Off

Normal status.

STATE Green/

Red

Green

Software Ready.

Blinking

Green

The AWK Search Utility has located the

AWK. (interval: 1sec).

Red

Booting or Error condition.

SIGNAL

(5 LEDs)

Green

Signal level

Off

Reserved

WLAN Green

WLAN is connected

Blinking

WLAN is transferring data

Off

WLAN is not in use or not working

properly.

LAN Green

Green

100/10 Mbps LAN port is active.

Blinking

Data is being transmitted

Off

100/10 Mbps LAN port is inactive

Specifications

WLAN Interface

Standards IEEE 802.11a/b/g for Wireless LAN

IEEE 802.3u 10/100BaseT(X) for Ethernet LAN

IEEE 802.3af for Power-over-Ethernet (PoE

models Only)

Spread Spectrum and

Modulation (typical)

DSSS with DBPSK, DQPSK, CCK

OFDM with BPSK, QPSK, 16QAM, 64QAM

802.11b:

•CCK @ 11/5.5 Mbps

•DQPSK @ 2 Mbps

•DBPSK @ 1 Mbps

802.11a/g:

•64QAM @ 54/48 Mbps

•16QAM @ 36/24 Mbps

•QPSK @ 18/12 Mbps

•BPSK @ 9/6 Mbps

Operating Channels

(central frequency)

US:

•2.412 to 2.462 GHz (11 channels)

•5.18 to 5.24 GHz (4 channels)

EU:

•2.412 to 2.472 GHz (13 channels)

•5.18 to 5.24 GHz (4 channels)

JP:

•2.412 to 2.484 GHz (14 channels, channel 14

- 10 -

only support DSSS)

•5.18 to 5.24 GHz (4 channels for W52)

Security

Firewall for MAC/IP/Protocol/Port-based filtering

64-bit and 128-bit WEP encryption,

WPA/WPA2-Personal and Enterprise (IEEE

802.1X/RADIUS, TKIP and AES)

Transmission Rates

802.11b: 1, 2, 5.5, 11 Mbps

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps

TX Transmit Power 802.11b:

•Typ. 18±1.5 dBm @ 1 to 11 Mbps

802.11g:

•Typ. 18±1.5 dBm @ 6 to 24 Mbps

•Typ. 17±1.5 dBm @ 36 Mbps

•Typ. 16±1.5 dBm @ 48 Mbps

•Typ. 16±1.5 dBm @ 54 Mbps

802.11a:

•Typ. 18±1.5 dBm @ 6 to 24 Mbps

•Typ. 16±1.5 dBm @ 36 Mbps

•Typ. 15±1.5 dBm @ 48 Mbps

•Typ. 14±1.5 dBm @ 54 Mbps

RX Sensitivity

802.11b:

•-97 dBm @ 1 Mbps

•-94 dBm @ 2 Mbps

•-92 dBm @ 5.5 Mbps

•-90 dBm @ 11 Mbps

802.11g:

•-88 dBm @ 6 to 24 Mbps

•-85 dBm @ 36 Mbps

•-75 dBm @ 48 Mbps

•-70 dBm @ 54 Mbps

802.11a:

•-88 dBm @ 6 to 24 Mbps

•-85 dBm @ 36 Mbps

•-75 dBm @ 48 Mbps

•-70 dBm @ 54 Mbps

Protocol Support

General Protocols

Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP,

TCP, UDP, RADIUS, SNMP, PPPoE, DHCP,LLDP

Interface

Default Antennas 1 dual-band omni-directional antennas, 2 dBi,

RP-SMA (male)

Connector for

External Antennas

2 RP-SMA (female)

RJ45 Ports

1, 10/100BaseT(X) auto negotiation speed, F/H

duplex mode, and auto MDI/MDI-X connection

Console Port

RS-232 (RJ45-type)

Reset

Present

LED Indicators

PWR, FAULT, STATE, SIGNEL, WLAN, LAN

Physical Characteristics

Housing

Metal, providing IP30 protection

Weight

400 g

Dimensions

50 x 115 x 70 mm

(1.98 x 4.53 x 2.76 in)

Installation

DIN-Rail mounting,

wall mounting (with optional kit)

Altri manuali per AWK-1121

Indice

Altri manuali Moxa Technologies Punto di accesso wireless

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies AWK-3121B Series Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A-M12-RCC-EU Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121-RTG Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-6222 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manuale utente

Moxa Technologies

Moxa Technologies AirWorks WK-1137C-EU-T Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-5232-M12-RCC Manuale utente

Moxa Technologies

Moxa Technologies AWK-4131 Manuale utente

Moxa Technologies

Moxa Technologies NPort NWH650 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131-RCC Series Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131-M12-RCC Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-622 Manuale utente

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Manuale utente

Moxa Technologies

Moxa Technologies AWK-3131A-RTG Series Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1151C Series Manuale utente

Moxa Technologies

Moxa Technologies Airworks AWK-3131A-M12-RCC Manuale utente

Moxa Technologies

Moxa Technologies WAC-1001 Series Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente