MPB PIRS Manuale di istruzioni

MPB S.r.l.

Via Giacomo Peroni 400/402

00131 Rome - Italy

Tel +39 0641200744

Fax +39 0641200653

[email protected]

www.gruppompb.uk.com

Quick start Manual PIRS

Quick Start Manual

PIRS

Quick start Manual Version: 1.1

Updated to the Software Version: 1.0.0

Updated to Firmware Version: 1.01

QUICK START MANUAL

PIRS

- 2 -

SAFETY NOTES

Read before using the product

MPB works to provide the best safety conditions available and complies with the latest safety

standards.

The instrumentation described in this manual was produced, tested and left the factory in

conditions that fully comply with European standards.

To ensure the correct use of the product, these general instructions must be read and

applied before and for any use of the instrumentation.

The PIRS is made for industrial environments and should be used by authorized staff only.

MPB disclaims any responsibility for a use of the device different from explained in the

manual.

In order to keep the 24 months warranty, please do not remove the seals of the instrument.

QUICK START MANUAL

PIRS

- 3 -

Declaration of conformity

(according to EMC 89/336/EEC directive and low voltage 73/23/EEC)

This is to certify that the product: PIRS

complies with the following European standards:

Safety: EN 61010-1 (undated reference, applies to all editions)

EMC emissions: EN 61326-1 (undated reference, applies to all editions)

EMC immunity: EN 61326-1 (undated reference, applies to all editions)

This product complies also with the 2014/35/CE Low voltage directive

requirements and with 2014/30/EU Electromagnetic compatibility

and with R0HS 2011/65/EU

MPB S.r.l.

 
 QUICK START MANUAL 
PIRS 
 
- 4 - 
 
 
 
Index 
 
General information .............................................................................................................................. - 5 - 
1. Introduction................................................................................................................................... - 5 - 
2. System description ........................................................................................................................ - 5 - 
3. System composition and optional accessories.............................................................................. - 5 - 
4. Technical specifications ................................................................................................................. - 6 - 
Operating principles .............................................................................................................................. - 7 - 
1. Block diagram ................................................................................................................................ - 7 - 
2. Working principles of PIRS............................................................................................................. - 7 - 
Software ................................................................................................................................................ - 8 - 
1. Installation..................................................................................................................................... - 8 - 
2. Connecting the instrument.......................................................................................................... - 10 - 
3. New list creation.......................................................................................................................... - 11 - 
4. Edit list ......................................................................................................................................... - 11 - 
5. Delete list..................................................................................................................................... - 11 - 
6. Delete frequency ......................................................................................................................... - 11 - 
7. Add frequency ............................................................................................................................. - 12 - 
8. Delete all frequency from list ...................................................................................................... - 12 - 
9. Wizard table ................................................................................................................................ - 12 - 
Calibration ........................................................................................................................................... - 13 - 
1. General ........................................................................................................................................ - 13 - 
2. Quiet zone pre-saved .................................................................................................................. - 13 - 
3. Quiet zone with sample probe .................................................................................................... - 13 - 
Measures ............................................................................................................................................. - 14 - 
1. setup ............................................................................................................................................ - 15 - 
- Turn on the PIRS .............................................................................................................................. - 15 - 
 
 
 

QUICK START MANUAL

PIRS

- 5 -

1.General information

1.1. Introduction

The PIRS (Portable Immunity Radiation System) is an innovative system to generate

amplified CW signals with calibration feedback.

1.2. System description

The PIRS can be used for Pre compliance Radiated Immunity Test (in accordance to the

IEC 61 000-4-3) and to generate the electric fields with intensity among 1 V/m and 30 V/m

inside shielding rooms, TEM and GTEM Cells, anechoic and semi anechoic chambers.

Thanks to its batteries power supply and its 8 hours autonomy (in generation and

continuous power amplification), it can be used with extreme ease in any environment,

mostly in “Situ” to perform Radiated Immunity Test on high dimensions devices hardly to

transport inside anechoic chambers or test labs.

Figure 1

1.3. System composition and optional accessories

Standard composition:

- PIRS

- Protective bag

QUICK START MANUAL

PIRS

- 6 -

Options:

- Tripod support NMR-01

- Tower up to 4m NMR-03

- Log periodic antenna LP-02

- Biconical antenna BC-01

- Biconical log periodic antenna BL-01

- PIRS converter

- RF Power meter

- Broadband meter

1.4. Technical specifications

Frequency Range

10 kHz … 3 GHz

Resolution

1 Hz

Connectorization

N-Type

Max output power (Typ)

37 dBm @1 MHz

Min output power (Typ)

3 dBm @ 3 GHz

Display

graphic 240x128

I/O interface

USB, fiber optic

Reference Standards

IEC 61000-4-3 (pre-compliance)

Operating Temperature

-10°…40°C

Certificate of Calibration

Standard; LAT

Dimensions

30 x 15 x 8 cm

Weight

1.7 kg

Power

8 batteries 18650 rechargeable and replaceable by the

operator

Custom list

From 128 to 500 points each

Auto calibration

- Set point

- Feedback tolerance

With sample probe or with mathematical model

Configurable for each list via software

Minimum user defined 2.5% (Typ 5%)

Feedback

- With sample probe

- With power meter

Configurable from one second minimum

Freq. freely configurable via PC

Freq. available on the antenna certificate

Persistence generation

Configurable from one second minimum

Compatibles tools

8053B, OR03, WBM, 6630F0A+6630

Technical specifications may change without notice

QUICK START MANUAL

PIRS

- 7 -

2. Operating principles

2.1. Block diagram

The block diagram below represents the PIRS:

Figure 2

2.2. Working principles of PIRS

The PIRS is an instrument design to speed up the generation of known electromagnetic

fields. Carrying out the proper calibration, using a sample probe (see cap 4Calibration) it is

possible to create, at selected frequencies, a table of power that the PIRS must generate

in order to have a target filed, chose by the operator. The field generated will be a function

of the distance of the object to be radiated, the type of antenna and the environment.

By the PIRS the operator creates a quite field area in which to immerse the instrument he

wants to test.

QUICK START MANUAL

PIRS

- 8 -

3. Software

3.1. Installation

Launch the setup file (setup.exe) and eventually click YES/Execute in the pop up window.

Please note that the PIRS SW can require to be “executed as administrator”.

Follow the steps as in the following figures.

Figure 3

QUICK START MANUAL

PIRS

- 9 -

Figure 4

Figure 5

QUICK START MANUAL

PIRS

- 10 -

Figure 6

3.2. Connecting the instrument

1) Start the PIRS Software, connect the USB cable to the computer and to the

instrument: at the first connection, wait for the driver installation, at the end of which

a notification of the operating system will appear

Figure 7

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente