National Instruments ExpressCard Strain-Relief Manuale utente

INSTALLATION GUIDE

ExpressCard Strain-Relief

Assembly

This guide describes how to install and use the ExpressCard strain-relief

assembly.

Introduction

The ExpressCard strain-relief assembly protects ExpressCards and

ExpressCard cables from unintentional disconnection.

What You Need to Get Started

❑ExpressCard strain-relief assembly

❑Your ExpressCard and cable

❑Hex key (included in your strain-relief assembly kit)

❑ExpressCard Strain-Relief Assembly Installation Guide

❑National Instruments embedded controller with an ExpressCard slot

Installation and Configuration

You can use the ExpressCard strain-relief assembly in two ways. The

first method secures only an ExpressCard. The second secures both an

ExpressCard and ExpressCard cable.

ExpressCard Strain-Relief Assembly Installation Guide 2 ni.com

To secure only an ExpressCard, refer to Figure 1 and follow these steps:

1. Install an ExpressCard in the controller ExpressCard slot.

2. Using the provided hex key, attach the security bracket in its rightmost

position to the controller front panel with the hex socket screws.

Figure 1. Securing Only an ExpressCard

To remove the ExpressCard, loosen but do not remove the screws. Slide the

security bracket to the left and remove the ExpressCard.

1 Hex Socket Screw (2x) 2 Security Bracket

RESET

10/100/1000

ACT/LINK

TRIG

DRIVE

PWR OK

©National Instruments Corporation 3 ExpressCard Strain-Relief Assembly Installation Guide

To secure both an ExpressCard and ExpressCard cable, refer to Figure 2

and follow these steps:

1. Install an ExpressCard in the controller ExpressCard slot.

2. Using the provided hex key, loosely attach the security bracket and

sliding bracket to the controller front panel with the hex socket screws.

3. Attach the ExpressCard cable.

4. Attach and tighten the clamping bracket with the thumb nuts.

5. With the security bracket in its rightmost position, tighten the hex

socket screws with the hex key.

Figure 2. Securing Both an ExpressCard and ExpressCard Cable

1 ExpressCard Cable

2 Thumb Nut (2x)

3 Clamping Bracket

4 Sliding Bracket

5 Security Bracket

6 Hex Socket Screw (2x)

RESET

10/100/1000

ACT/LINK

TRIG

DRIVE

PWR OK

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. The ExpressCard™ word mark and logos are owned by PCMCIA and any use

of such marks by National Instruments is under license. Other product and company names mentioned

herein are trademarks or trade names of their respective companies. For patents covering

National Instruments products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at

ni.com/patents.

Figure 3 shows a secured ExpressCard and ExpressCard cable.

Figure 3. Secured ExpressCard and ExpressCard Cable

Note The ExpressCard strain-relief assembly cannot strain relieve cables when an

extended ExpressCard is installed. Also, the assembly may be unable to strain relieve

cables with very large or unusually shaped housings. However, when you cannot strain

relieve the ExpressCard cable, you still can secure the ExpressCard itself as shown in

Figure 1.

RESET

10/100/1000

ACT/LINK

TRIG

DRIVE

PWR OK

Indice

Altri manuali National Instruments Hardware per computer

National Instruments

National Instruments PCI-1407 Manuale di istruzioni

National Instruments

National Instruments NI PXI-8221 Manuale utente

National Instruments

National Instruments PXI-8170 Series Manuale utente

National Instruments

National Instruments NI-9238 Manuale utente

National Instruments

National Instruments DAQPad-6020E Manuale utente

National Instruments

National Instruments PXIe-1082DC Manuale utente

National Instruments

National Instruments NI 5922 Manuale

National Instruments

National Instruments MXI Express x4 Manuale utente

National Instruments

National Instruments PXIe-8822 Manuale utente

National Instruments

National Instruments 9260 Manuale utente

National Instruments

National Instruments PXI-8101 Manuale utente

National Instruments

National Instruments PXIe-8108 Manuale utente

National Instruments

National Instruments NI 9213 Manuale utente

National Instruments

National Instruments PXIe-5832 Manuale utente

National Instruments

National Instruments PCI-8430 Manuale utente

National Instruments

National Instruments CPCI-GPIB Manuale utente

National Instruments

National Instruments GPIB-ENET-1000 Manuale utente

National Instruments

National Instruments PXI-8335 Manuale utente

National Instruments

National Instruments PXIe-7911 Manuale utente

National Instruments

National Instruments NI 9472 Manuale utente

National Instruments

National Instruments NI roboRIO Manuale utente

National Instruments

National Instruments PXIe-8100 Manuale utente

National Instruments

National Instruments NI PXIe-1085 Manuale utente

National Instruments

National Instruments USRP-2940 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente