National Instruments NI 9235 Manuale utente
GETTING STARTED GUIDE
NI 9235
10 kS/s/channel, 120 Ω Quarter-Bridge Strain
Gage, 8-Channel C Series Strain/Bridge Input
Module
This document explains how to connect to the NI 9235.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9235. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Safety Guidelines
Operate the NI 9235 only as described in this document.
Caution This icon denotes a caution, which advises
you to consult documentation where this symbol is
marked.
Caution Do not operate the NI 9235 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
2| ni.com | NI 9235 Getting Started Guide
built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for
repair.
Safety Voltages
Connect only voltages that are within the following limits:
Between any two terminals ±30 V maximum
Isolation
Channel-to-channel None
Channel-to-earth ground
Continuous 60 V DC,
Measurement Catergory I
Withstand 1,000 V RMS, verified by a 5 s
dielectric withstand test
Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution system
referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This category is
for measurements of voltages from specially protected secondary
circuits. Such voltage measurements include signal levels, special
NI 9235 Getting Started Guide | © National Instruments | 3
equipment, limited-energy parts of equipment, circuits powered
by regulated low-voltage sources, and electronics.
Caution Do not connect the NI 9235 to signals or use
for measurements within Measurement Categories II,
III, or IV.
Safety Guidelines for Hazardous Locations
The NI 9235 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
NI 9235 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2, or Zone 2.
4| ni.com | NI 9235 Getting Started Guide
Caution The system must be installed in an enclosure
certified for the intended hazardous (classified)
location, having a tool secured cover/door, where a
minimum protection of at least IP54 is provided.
Special Conditions for Hazardous Locations Use
in Europe and Internationally
The NI 9235 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO 07 ATEX 0626664X and is IECEx UL 14.0089X
certified. Each NI 9235 is marked II 3G and is suitable for use
in Zone 2 hazardous locations, in ambient temperatures of -40 °C
≤ Ta ≤ 70 °C. If you are using the NI 9235 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
Caution Transient protection shall be provided that is
set at a level not exceeding 140% of the peak rated
voltage value of 85 V at the supply terminals to the
equipment.
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC/EN 60664-1.
NI 9235 Getting Started Guide | © National Instruments | 5
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
stated in the product specifications. These requirements and
limits provide reasonable protection against harmful interference
when the product is operated in the intended operational
electromagnetic environment.
This product is intended for use in industrial locations. However,
harmful interference may occur in some installations, when the
product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize
interference with radio and television reception and prevent
unacceptable performance degradation, install and use this
6| ni.com | NI 9235 Getting Started Guide
product in strict accordance with the instructions in the product
documentation.
Furthermore, any changes or modifications to the product not
expressly approved by National Instruments could void your
authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance,
operate this product only with shielded cables and
accessories.
Special Conditions for Marine Applications
Some products are Lloyd’s Register (LR) Type Approved for
marine (shipboard) applications. To verify Lloyd’s Register
certification for a product, visit ni.com/certification and search
for the LR certificate, or look for the Lloyd’s Register mark on
the product.
Caution In order to meet the EMC requirements for
marine applications, install the product in a shielded
enclosure with shielded and/or filtered power and
input/output ports. In addition, take precautions when
designing, selecting, and installing measurement probes
NI 9235 Getting Started Guide | © National Instruments | 7
and cables to ensure that the desired EMC performance
is attained.
Preparing the Environment
Ensure that the environment in which you are using the NI 9235
meets the following specifications.
Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)
-40 °C to 70 °C
Operating humidity
(IEC 60068-2-78)
10% RH to 90% RH,
noncondensing
Pollution Degree 2
Maximum altitude 5,000 m
Indoor use only.
Note Refer to the device datasheet on ni.com/manuals
for complete specifications.
8| ni.com | NI 9235 Getting Started Guide
NI 9235 Pinout
EXC1
AI1
RC1
EXC3
AI3
RC3
EXC5
AI5
RC5
EXC7
AI7
RC7
EXC0
AI0
RC0
EXC2
AI2
RC2
EXC4
AI4
RC4
EXC6
AI6
RC6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
NI 9235 Getting Started Guide | © National Instruments | 9
Table 1. Signal Descriptions
Signal Description
AI Analog input signal connection
EXC Excitation source connection
RC Quarter-bridge completion connection
NI 9235 Connection Guidelines
• Make sure that devices you connect to the NI 9235 are
compatible with the module specifications.
• You must use 2-wire ferrules to create a secure connection
when connecting more than one wire to a single terminal on
the NI 9235.
• Push the wire into the terminal when using a solid wire or a
stranded wire with a ferrule.
• Open the terminal by pressing the push button when using
stranded wire without a ferrule.
10 | ni.com | NI 9235 Getting Started Guide
Altri manuali per NI 9235
1
Indice
Altri manuali National Instruments Unità di controllo
National Instruments
National Instruments R Series Manuale utente
National Instruments
National Instruments NI 9853 Manuale utente
National Instruments
National Instruments ELVIS RIO CM Manuale utente
National Instruments
National Instruments PXIe-8240 Manuale utente
National Instruments
National Instruments CompactRIO cRIO-FRC Manuale utente
National Instruments
National Instruments PXIe-4339 Manuale utente
National Instruments
National Instruments NI 9401 Manuale utente
National Instruments
National Instruments PXIe-4302 Manuale utente
National Instruments
National Instruments cRIO-9068 Manuale utente
National Instruments
National Instruments NI 9215 Manuale
National Instruments
National Instruments NI ISM-7401 Manuale utente
National Instruments
National Instruments PXIe-8830mc Manuale utente
National Instruments
National Instruments NI 9225 Manuale
National Instruments
National Instruments 9775 Manuale
National Instruments
National Instruments SLSC-12101 Manuale utente
National Instruments
National Instruments PXIe-8861 Manuale utente
National Instruments
National Instruments NI 9269 Manuale utente
National Instruments
National Instruments PXI-6683 Series Manuale utente
National Instruments
National Instruments PXIe-6591R Manuale utente
National Instruments
National Instruments 9755 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
