National Instruments NI 9478 Manuale utente

GETTING STARTED GUIDE

NI 9478

16 DO, 0 V to 50 V, Sinking, 50 μs

This document explains how to connect to the NI 9478.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9478. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9478 only as described in this document.

Caution Do not operate the NI 9478 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

2| ni.com | NI 9478 Getting Started Guide

Safety Voltages

Connect only voltages that are within the following limits:

Vsup-to-COM 50 VDC maximum,

Measurement Category I

Isolation

Channel-to-channel None

Channel-to-earth ground

Continuous 60 VDC,

Measurement Category I

Withstand 1,000 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

NI 9478 Getting Started Guide | © National Instruments | 3

Caution Do not connect the NI 9478 to signals or use

for measurements within Measurement Categories II,

III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

intended for direct connection to the MAINS building

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

Safety Guidelines for Hazardous Locations

The NI 9478 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9478 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

4| ni.com | NI 9478 Getting Started Guide

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Caution For Division 2 and Zone 2 applications,

install a protection device across the external power

supply and the COM pin. The device must prevent the

external power supply voltage from exceeding 70 V if

there is a transient overvoltage condition.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9478 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx UL 14.0089X certified. Each NI 9478 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9478

NI 9478 Getting Started Guide | © National Instruments | 5

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

6| ni.com | NI 9478 Getting Started Guide

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

NI 9478 Getting Started Guide | © National Instruments | 7

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI 9478

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

8| ni.com | NI 9478 Getting Started Guide

Note Refer to the device datasheet on ni.com/manuals

for complete specifications.

NI 9478 Getting Started Guide | © National Instruments | 9

NI 9478 Pinout

DO0

DO1

DO2

DO3

DO4

DO5

DO6

DO7

Vsup

DO8

DO9

DO10

DO11

DO12

DO13

DO14

DO15

COM

Vsup

COM

10 | ni.com | NI 9478 Getting Started Guide

Altri manuali per NI 9478

Indice

Altri manuali National Instruments Unità di controllo

National Instruments

National Instruments NI 9214 Manuale utente

National Instruments

National Instruments 5761R Manuale utente

National Instruments

National Instruments PXIe-5694 Manuale utente

National Instruments

National Instruments 9756 Manuale utente

National Instruments

National Instruments PXIe-4353 Manuale

National Instruments

National Instruments NI 9227E Manuale utente

National Instruments

National Instruments NI 9212 Manuale utente

National Instruments

National Instruments 7330 Manuale utente

National Instruments

National Instruments NI 9882 Manuale utente

National Instruments

National Instruments NI USB-9264 Manuale utente

National Instruments

National Instruments NI 9250 Manuale utente

National Instruments

National Instruments sbRIO-9609 Manuale utente

National Instruments

National Instruments SCC-A10 Manuale utente

National Instruments

National Instruments NI PXI-6682H Manuale utente

National Instruments

National Instruments PXIe-6594 Manuale utente

National Instruments

National Instruments 9266 Manuale utente

National Instruments

National Instruments NI FlexRIO PXI-7952R Manuale utente

National Instruments

National Instruments SCXI-1104 Manuale utente

National Instruments

National Instruments FieldPoint FP-DI-301 Manuale utente

National Instruments

National Instruments SCC-DO01 Manuale utente

National Instruments

National Instruments NI PXIe-7976R Manuale utente

National Instruments

National Instruments NI 9211 Manuale utente

National Instruments

National Instruments NI 9234 Manuale utente

National Instruments

National Instruments FlexRIO PXIe-79 R Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente