National Instruments PXImc Series Manuale utente

GETTING STARTED GUIDE

NI PXImc Devices

NI PXIe-8830mc PXImc Processor Module

This document includes instructions for installing and configuring your NI PXIe-8830mc

PXImc processor module.

Contents

Products Covered...................................................................................................................... 1

Conventions.............................................................................................................................. 2

Getting Started.......................................................................................................................... 2

Unpacking......................................................................................................................... 2

Electrical........................................................................................................................... 2

Preparing the Environment............................................................................................... 3

Hardware Installation........................................................................................................3

Powering On the PXImc System...................................................................................... 4

Powering Off the PXImc System......................................................................................4

Software Installation and Configuration........................................................................... 4

LabVIEW RT Installation................................................................................................. 4

NI PXIe-8830mc Front Panel........................................................................................... 8

Removing the NI PXIe-8830mc from a PXI Express Chassis..........................................9

Cleaning............................................................................................................................ 9

Common Configuration Questions......................................................................................... 10

General Questions........................................................................................................... 10

Upgrade Information.......................................................................................................10

Troubleshooting.......................................................................................................................11

What if the processor module does not boot?................................................................. 11

My system boots fine as long as a particular module is not in my chassis.....................12

My CMOS is corrupted. How do I set it back to default?.............................................. 12

Worldwide Support and Services............................................................................................ 13

Products Covered

This document covers the following products:

• NI PXIe-8830mc (156252x-011L)

Note Following the model number above is the specific NI assembly number in

parentheses. Ensure that the specifications of interest match the NI assembly number

printed on the board. x denotes all letter revisions of the assembly.

Conventions

The following conventions appear in this manual:

CompactPCI Express/

CPCIe

The terms CompactPCI Express and CPCIe are interchangeable

in this guide.

PCI Express/PCIe The terms PCI Express and PCIe are interchangeable in this

guide.

PXI Express/PXIe The terms PXI Express and PXIe are interchangeable in this

guide.

Getting Started

This section includes instructions for unpacking and installing your NI PXIe-8830mc

processor module, including setting up your processor module to run LabVIEW Real-Time. It

also describes the processor module's front panel connectors.

Unpacking

The NI PXIe-8830mc ships in an antistatic package to prevent electrostatic discharge from

damaging device components. To prevent such damage when handling the device, ground

yourself using a grounding strap or by holding a grounded object, such as your computer

chassis, and complete the following steps:

1. Touch the antistatic package to a metal part of the chassis before removing the device

from the package.

Caution Never touch the exposed pins of connectors.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

3. Notify National Instruments if the device appears damaged in any way. Do not install a

damaged device into your chassis.

Electrical

Power Rail Typical Current Maximum Current

+3.3 V 1450 mA 2180 mA

+12 V 3750 mA 3940 mA

+5 VAux 70 mA 110 mA

Note: Does not include any attached USB devices.

2| ni.com | NI PXImc Devices Getting Started Guide

Preparing the Environment

Ensure the environment you are using the NI PXIe-8830mc in meets the following

specifications.

............................................................................Ambient temperature range

(maximum performance)

0 to 40 °C

............................................................................Ambient temperature range 0 to 55 °C (Tested in accordance with

IEC-60068-2-1 and IEC-60068-2-2. Meets

MIL-PRF-28800F Class 3 low temperature

limit and MIL-PRF-28800F Class 2 high

temperature limit.)

............................................................................Relative humidity range 10 to 90%, noncondensing (Tested in

accordance with IEC-60068-2-56.)

............................................................................Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

............................................................................Pollution Degree 2

Indoor use only.

Note Refer to the NI PXIe-8830mc User Manual for full NI PXIe-8830mc

specifications.

Hardware Installation

The following are general instructions for installing the NI PXIe-8830mc.

Complete the following steps to install the NI PXIe-8830mc in your PXI Express chassis.

1. Power off your PXI Express chassis, but leave it plugged in while installing the NI

PXIe-8830mc. The power cord grounds the chassis and protects it from electrical damage

while you install the module.

Caution To protect both yourself and the chassis from electrical hazards,

leave the chassis off until you finish installing the NI PXIe-8830mc.

2. Remove or open any doors or covers blocking access to the slot in which you intend to

install the NI PXIe-8830mc.

3. Touch a metal part of the chassis to discharge any static electricity that might be on your

clothes or body.

4. Make sure the injector/ejector handle is in its downward position. Be sure to remove all

connector packaging and protective caps from retaining screws on the module.

5. Identify the slot in which the NI PXIe-8830mc will be installed in the chassis. Refer to

the following table to determine which slot types the NI PXIe-8830mc is compatible

with.

NI PXImc Devices Getting Started Guide | © National Instruments | 3

Table 1. NI PXIe-8830mc Slot Type Compatibility

NI PXI Express Product

PXI Express Chassis

Controller Peripheral Hybrid

NI PXIe-8830mc — X X

6. Align the NI PXIe-8830mc with the card guides on the top and bottom of the slot. Hold

the handle as you slowly slide the module into the chassis until the handle catches on the

injector/ejector rail.

Caution Do not raise the injector/ejector handle as you insert the NI

PXIe-8830mc. It will not insert properly unless the handle is in its downward

position so that it does not interfere with the injector/ejector rail on the chassis.

7. Raise the injector/ejector handle until the module firmly seats into the backplane

receptacle connectors. The front panel of the NI PXIe-8830mc should be even with the

front panel of the chassis.

8. Tighten the bracket-retaining screws on the top and bottom of the front panel to secure

the NI PXIe-8830mc to the chassis.

9. Replace or close any doors or covers to the chassis.

Powering On the PXImc System

The NI PXIe-8830mc powers on automatically when the chassis is powered on. To power on

the NI PXIe-8830mc, turn on the chassis. The NI PXIe-8830mc boots up to OS when the

system controller boots up when the chassis is powered on.

Powering Off the PXImc System

The NI PXIe-8830mc powers off automatically when the chassis is powered off. You also can

power off the NI PXIe-8830mc by shutting down the system controller.

Software Installation and Configuration

The NI PXIe-8830mc requires the NI-PXImc driver software to enable its features. Refer to

the readme.html file on the NI-PXImc driver DVD for software installation instructions.

LabVIEW RT Installation

This section explains software installation and switch configuration for LabVIEW RT on your

PXImc processor module.

LabVIEW RT Software Installation

The following section describes the necessary steps to set up your PXImc processor module to

run LabVIEW Real-Time. In this section you will configure the processor module boot mode,

verify or change IP settings, and install LabVIEW Real-Time software.

Complete the following steps to install the LabVIEW RT software.

1. Boot the NI PXImc processor module into the real-time operating system.

The PXImc processor module automatically boots into LabVIEW RT Safe Mode when no

software is installed. LabVIEW RT Safe Mode loads with the basic real-time operating

4| ni.com | NI PXImc Devices Getting Started Guide

system and automatically attempts to connect to the network using DHCP. If DHCP is not

available, it then connects to the network with a link-local IP address.

2. Open Measurement & Automation Explorer (MAX) on another computer in the same

subnet and expand the Remote Systems branch. MAX lists the PXImc processor module

as the model name of the processor module followed by the MAC address (for example,

NI-PXIe-8830mc 00802f108562).

Note The other computer must have LabVIEW, LabVIEW RT, and any

desired drivers installed.

Tip Record the PXImc processor module MAC address, located on the side of

the processor module, for use in identifying the processor module. You also can

remove the label and place it on the front of the processor module for easier

access.

3. Click the appropriate PXImc processor module entry to access the Network Settings tab

in the right pane view.

4. (Optional) Enter a name for the RT target in the Name text box.

5. (Optional) Set the network configuration options of the RT target in the IP Settings

section and click the Apply button.

For information about configuring network settings, refer to Configuring Network

Settings in Measurement & Automation Explorer Help, accessible by browsing to MAX

Remote Systems Help»LabVIEW Real-Time Target Configuration»Configuring

Network Settings from the help Contents tab.

Note When any IP or identification settings are changed, you are prompted to

reboot the processor module for the changes to take effect. Click Yes to reboot

the RT target automatically. You also can reboot the processor module by right-

clicking on the target name under Remote Systems and selecting Reboot.

After rebooting the PXImc processor module, it appears in the Remote Systems category

with the assigned name.

6. Expand the PXImc processor module view in the Remote Systems branch and select

Software.

7. Click the Add/Remove Software button in the toolbar to launch the LabVIEW Real-

Time Software Wizard.

8. Install the LabVIEW Real-Time software and device drivers that you require on the RT

target. (At a minimum, you must install LabVIEW RT and PXImc drivers.) Refer to the

NI website at ni.com/info and enter the Info Code etspc for the latest information

about supported software.

After software installation, the processor module automatically reboots, and you now can

program it using LabVIEW Real-Time.

Note Refer to Getting Started with the LabVIEW Real-Time Module on your host

computer for more information about setting up your RT target.

NI PXImc Devices Getting Started Guide | © National Instruments | 5

LabVIEW RT Configuration Switches

Use the LabVIEW RT configuration switches to configure LabVIEW RT if it is installed on

the processor module. If you are not using LabVIEW RT, these switches should remain in the

OFF position. The processor module reads these switches only after a system reset.

The NI PXIe-8830mc processor module includes the following LabVIEW RT configuration

switches:

• Switch 1—Boot LabVIEW RT: Set this switch to ON to boot LabVIEW RT.

• Switch 2—Boot Safe Mode: Set this switch to ON to boot LabVIEW RT into safe mode

to reconfigure TCP/IP settings and to download or update software from a host computer.

This switch overrides the behavior of Switch 1. Booting the processor module into safe

mode does not start the embedded LabVIEW RT engine. After changing the settings or

software, reboot the processor module with this switch OFF to resume normal operation.

• Switch 3—Disable Startup VI: Set this switch to ON to prevent VIs from automatically

running at startup if the processor module becomes inaccessible because of a startup VI.

• Switch 4—Reset IP Address: Set this switch to ON to reset the IP address and other

TCP/IP settings to their factory defaults. Use this switch if moving the processor module

to a different subnet or if the current TCP/IP settings are invalid.

Note By default, the target automatically attempts to connect to the network using

DHCP. If the target cannot initiate a DHCP connection, the target connects to the

network with a link-local IP address or 169.254.x.x.

The following figure shows the location of the LabVIEW RT configuration switches. The

switches are shown in the OFF position.

6| ni.com | NI PXImc Devices Getting Started Guide

Figure 1. LabVIEW RT Configuration Switches

1. Switch 1—Boot LabVIEW RT

2. Switch 2—Boot Safe Mode

3. Switch 3—Disable Startup VI

4. Switch 4—Reset IP Address

NI PXImc Devices Getting Started Guide | © National Instruments | 7

NI PXIe-8830mc Front Panel

The following figure shows the front panel layout of the NI PXIe-8830mc.

Figure 2. NI PXIe-8830mc Front Panel

1. Reset Button

2. Ethernet Connector

3. USB Connectors

4. User 1 LED

5. User 2 LED

6. PWR OK/FAULT LED

7. Drive LED

Front Panel Connectors

The following table lists various peripherals and their corresponding NI PXIe-8830mc external

connectors, bus interfaces, and functions.

Peripheral External Connector Description

Ethernet Port LAN (RJ45) 10/100/1000 Ethernet

Intel i217

USB 2.0 USB 4-pin Series A stacked receptacle (2 ports) USB 2.0 capable

8| ni.com | NI PXImc Devices Getting Started Guide

Front Panel Features

The NI PXIe-8830mc has the following front-panel features:

• A system reset pushbutton (press the button to reset the processor module).

• Four front panel LEDs that show PC status:

–PWR OK/FAULT LED—Indicates the processor module status. The LED indicates

one of the following states:

• Green ON steady—PXI Express and onboard power is on and within regulation

limits.

• Green BLINKING—The processor module has entered the soft off state and is

safe to power down.

Note Applicable only when chassis is set to Manual.

• OFF—The processor module is powered off.

• Red BLINKING—The processor module detected a power rail fault when

trying to boot.

• Red Solid—The processor module detected a thermal fault and has shut down

to protect the system.

–USER —Two bi-color green/yellow LEDs (USER 1 and USER 2) that you can

define to meet the needs of your LabVIEW application.

–DRIVE —Indicates when an access to the internal hard disk is occurring.

Removing the NI PXIe-8830mc from a PXI Express

Chassis

To remove the NI PXIe-8830mc from a PXI Express chassis, complete the following steps.

1. Power off the chassis.

2. Remove any cables that may be attached to the processor module front panel.

3. Unscrew the 4 bracket-retaining screws in the front panel.

4. Press the injector/ejector handle down.

5. Slide the unit out of the chassis.

Cleaning

Use a dry, low-velocity stream of air to clean the NI PXIe-8830mc processor module. If

needed, use a soft, nonmetallic brush for cleaning around components.

Make sure that the device is completely dry and free from contaminants before returning it to

service.

NI PXImc Devices Getting Started Guide | © National Instruments | 9

Common Configuration Questions

This section answers common configuration questions you may have when using an

NI PXIe-8830mc processor module.

General Questions

What do the LEDs on the front panel mean?

Refer to the LED status descriptions in the Front Panel Features section.

After shutting down my NI PXIe-8830mc, the Ethernet LEDs

continue to blink. Is it safe to remove my processor module or

disconnect power?

The NI PXIe-8830mc Intel WGI217LM Ethernet device remains powered even after

shutdown. It is safe to remove your processor module or disconnect power.

Upgrade Information

How do I upgrade system memory?

You can change the amount of installed RAM on the NI PXIe-8830mc by upgrading the

DDR4 SO-DIMMs. Complete the following steps to upgrade the RAM.

1. Remove theNI PXIe-8830mc from the PXI Express chassis.

2. Locate the DDR4 SO-DIMM module on the side of the processor module, as shown in

the figure.

3. Remove the installed DDR4 SO-DIMM module, if necessary.

4. Install the new DDR4 SO-DIMM module into the slot.

NI PXIe-8830mc System Memory Information

National Instruments offers the following types of SO-DIMMs for use with the

NI PXIe-8830mc processor module.

Note National Instruments has tested and verified that the DDR3 SO-DIMMs we

sell work with the NI PXIe-8830mc processor module. We recommend you purchase

your DDR3 SO-DIMM modules from National Instruments. Other off-the-shelf

DDR3 SO-DIMM modules are not guaranteed to work properly.

• PC3-12800 (DDR3 1600) 4 GB, 256 MB × 64, CL 9, 1.18 in. max (NI part number

782341-4096)

• PC3-12800 (DDR3 1600) 8 GB, 512 MB × 64, CL 9, 1.18 in. max (NI part number

782341-8192)

10 | ni.com | NI PXImc Devices Getting Started Guide

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali National Instruments Unità di controllo

National Instruments

National Instruments SCXI -1122 Manuale

National Instruments

National Instruments NI 9251 Manuale utente

National Instruments

National Instruments PXIe-4310 Manuale

National Instruments

National Instruments NI FlexRIO Manuale utente

National Instruments

National Instruments 9861 Manuale utente

National Instruments

National Instruments PXIe-4302 Manuale utente

National Instruments

National Instruments NI-9208 Manuale utente

National Instruments

National Instruments SCXI Series Manuale utente

National Instruments

National Instruments NI PXI/e-4000 Series Manuale utente

National Instruments

National Instruments NI 9881 Manuale utente

National Instruments

National Instruments NI PXI-4220 Manuale utente

National Instruments

National Instruments FieldPoint FP-1001 Manuale utente

National Instruments

National Instruments PXI-8840 Quad-Core Manuale utente

National Instruments

National Instruments NI 9401 Manuale utente

National Instruments

National Instruments sbRIO-9205 Manuale utente

National Instruments

National Instruments SCC-SG Series Manuale utente

National Instruments

National Instruments NI 9503 Manuale utente

National Instruments

National Instruments PXIe-4480 Manuale utente

National Instruments

National Instruments BNC-208X Series Manuale utente

National Instruments

National Instruments PXIe-6591R Manuale utente

National Instruments

National Instruments SCC-LP Series Manuale utente

National Instruments

National Instruments FieldPoint cFP-DI-304 Manuale utente

National Instruments

National Instruments NI PXIe-7972R Manuale utente

National Instruments

National Instruments NI USB-9201 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente