National Instruments CRIO-9064 Manuale utente

GETTING STARTED GUIDE

NI cRIO-9064

Embedded Real-Time Controller with Reconfigurable FPGA for C

Series Modules

This document describes how to begin using the NI cRIO-9064.

Safety Guidelines

Caution Do not operate the cRIO-9064 in a manner not specified in this document.

Product misuse can result in a hazard. You can compromise the safety protection

built into the product if the product is damaged in any way. If the product is

damaged, return it to NI for repair.

Safety Guidelines for Hazardous Locations

The cRIO-9064 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous

locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations; and

nonhazardous locations only. Follow these guidelines if you are installing the cRIO-9064 in a

potentially explosive environment. Not following these guidelines may result in serious injury

or death.

Caution Do not disconnect the power supply wires and connectors from the

controller unless power has been switched off.

Caution Do not disconnect I/O-side wires or connectors unless power has been

switched off or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched off or the area is

known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications, install the system in an enclosure

rated to at least IP54 as defined by IEC/EN 60079-15.

Caution The USB ports require the retention accessories listed in the following

table for hazardous locations. All cables must be used in a conduit or cable gland to

wire to a nonhazardous location. Do not disconnect a cable unless the cRIO-9064 is

powered off or the area is known to be nonhazardous.

Table 1. Hazardous Location Retention Accessories

Port Required Accessory Part Number

USB Device Port NI Locking USB Cable 157788-01

USB Host Port NI Industrial USB Extender Cable 152166-xx

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The cRIO-9064 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO Certificate

No. 12 ATEX 1202658X and is IECEx UL 14.0089X certified. Each device is marked II

3G and is suitable for use in Zone 2 hazardous locations, in ambient temperatures of -20 °C ≤

Ta ≤ 55 °C.

Caution You must make sure that transient disturbances do not exceed 140% of

the rated voltage.

Caution The system shall only be used in an area of not more than Pollution

Degree 2, as defined in IEC 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified enclosure with

a minimum ingress protection rating of at least IP54 as defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the use of a

tool.

2| ni.com | NI cRIO-9064 Getting Started Guide

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for marine (shipboard) applications.

To verify Lloyd’s Register certification for a product, visit ni.com/certification and search for

the LR certificate, or look for the Lloyd’s Register mark on the product.

Caution In order to meet the EMC requirements for marine applications, install the

product in a shielded enclosure with shielded and/or filtered power and input/output

ports. In addition, take precautions when designing, selecting, and installing

measurement probes and cables to ensure that the desired EMC performance is

attained.

Preparing the Environment

Ensure that the environment in which you are using the cRIO-9064 meets the following

specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-20 °C to 55 °C

Operating humidity (IEC 60068-2-56) 10% RH to 90% RH, noncondensing

Pollution degree 2

Maximum altitude 5,000

NI cRIO-9064 Getting Started Guide | © National Instruments | 3

Indoor use only.

Note Refer to the device specifications on ni.com/manuals for complete

specifications.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

Verifying the Kit Contents

Verify that the following items are included in the cRIO-9064 kit.

Figure 1. cRIO-9064 Kit Contents

1. cRIO Device

2. USB A-to-B Cable

3. NI CompactRIO Device Drivers Media

4. Getting Started Guide

Installing Software on the Host Computer

Before using the cRIO-9064, you must install the following application software and device

drivers on the host computer in this order:

1. LabVIEW 2014 SP1 or later

2. LabVIEW Real-Time Module 2014 SP1 or later

4| ni.com | NI cRIO-9064 Getting Started Guide

3. LabVIEW FPGA Module 2014 SP1 or later1

4. NI-RIO Device Drivers 14.5 or later

For minimum software support information, visit ni.com/info and enter the Info Code

swsupport.

Installing C Series Modules

Complete the following steps to install a C Series module.

1. Verify that power is not connected to the I/O connector(s) on the C Series module. If the

system is in a nonhazardous location, the cRIO-9064 can be powered on when you install

modules.

2. Press the latches on the C Series module.

3. Align the C Series module with a slot and seat it in the slot until the latches lock in place.

Removing C Series Modules

Verify that power is not connected to the I/O connector(s) on the C Series module before you

remove a module from the cRIO-9064. If the system is in a nonhazardous location, the

cRIO-9064 can be powered on when you remove modules.

Connecting the cRIO-9064

The cRIO-9064 has the following connectors, LEDs, and buttons.

1LabVIEW FPGA Module is not required when using Scan Interface mode. To program the user-

accessible FPGA on the cRIO-9064, LabVIEW FPGA Module is required.

NI cRIO-9064 Getting Started Guide | © National Instruments | 5

Figure 2. cRIO-9064 Front Panel

5678

1. LEDs

2. USB Device Port

3. RS-232 Serial Port

4. RJ-45 Ethernet Port 2

5. RJ-45 Ethernet Port 1

6. USB Host Port

7. Power Connector

8. RESET Button

Connecting the cRIO-9064 to Ground

You must connect the cRIO-9064 grounding terminal to the grounding electrode system of the

facility.

What to Use

• Ring lug

• Wire, 2.1 mm2 (14 AWG) or larger

• Screwdriver, Phillips #2

What to Do

Complete the following steps to ground the cRIO-9064.

1. Attach the ring lug to the wire.

2. Remove the grounding screw from the grounding terminal on the cRIO-9064.

3. Attach the ring lug to the grounding terminal.

4. Tighten the grounding screw to 0.5 N · m (4.4 lb · in.) of torque.

5. Attach the other end of the wire to the grounding electrode system of your facility using a

method that is appropriate for your application.

6| ni.com | NI cRIO-9064 Getting Started Guide

Caution If you use shielded cabling to connect to a C Series module with a plastic

connector, you must attach the cable shield to the chassis grounding terminal using

2.1 mm2 (14 AWG) or larger wire. Attach a ring lug to the wire and attach the wire

to the chassis grounding terminal. Solder the other end of the wire to the cable

shield. Use shorter wire for better EMC performance.

For more information about ground connections, visit ni.com/info and enter the Info Code

emcground.

Connecting the cRIO-9064 to Power

The cRIO-9064 requires a 9 V to 30 V external power supply. The cRIO-9064 filters and

regulates the supplied power and provides power for the C Series modules. The cRIO-9064

has one layer of reverse-voltage protection.

The following table lists the POWER LED indicators.

Table 2. POWER LED Indicators

LED Color LED Pattern Indication

Green Solid The cRIO-9064 is powered on and the connected power supply is

adequate.

— Off The cRIO-9064 is powered off.

What to Use

• Screwdriver, 2.54 mm (0.10 in.) flathead

• Power supply, 9 V to 30 V, 18 W maximum

NI recommends the power supply listed in the following table for the cRIO-9064.

Table 3. NI Power Supplies

Power Supply Part Number

NI PS-15 Industrial Power Supply

(24 VDC, 5 A, 100 VAC to 120 VAC/200 VAC to 240 VAC input)

781093-01

What to Do

Complete the following steps to connect a power supply to the cRIO-9064.

1. Ensure that your power supply is powered off.

2. Remove the power connector from the cRIO-9064.

Caution Do not tighten or loosen the terminal screws on the power connector

while the cRIO-9064 is powered on.

3. Connect the power supply to the power connector, as shown in the following figure.

NI cRIO-9064 Getting Started Guide | © National Instruments | 7

Figure 3. cRIO-9064 Power Connections

Power Connector

Power Supply

–

Note The C terminals are internally connected to each other.

4. Tighten the terminal screws on the power connector to 0.20 N · m to 0.25 N · m

(1.8 lb · in. to 2.2 lb · in.) of torque.

5. Install the power connector on the front panel of the cRIO-9064.

6. Tighten the power connector screw flanges to 0.20 N · m to 0.25 N · m (1.8 lb · in. to

2.2 lb · in.) of torque.

7. Power on the power supply.

Powering On the cRIO-9064

When you power on the cRIO-9064 for the first time, the device boots into safe mode. The

POWER LED illuminates, the STATUS LED illuminates briefly, and then the STATUS LED

blinks twice every few seconds.

Connecting the cRIO-9064 to the Host Computer

Complete the following steps to connect the cRIO-9064 to the host computer using the USB

device port.

1. Power on the host computer.

2. Connect the cRIO-9064 to the host computer using the USB A-to-B cable.

Caution NI requires the use of a locking USB cable (157788-01) to meet the

shock and vibration specifications. Refer to the specifications on ni.com/

manuals for shock and vibration specifications.

The device driver software automatically detects the cRIO-9064. If the device driver

software does not detect the cRIO-9064, verify that you installed the appropriate NI

software in the correct order on the host computer.

Tip You can also use the Ethernet port to connect directly to the host computer or

network. Refer to the user manual on ni.com/manuals for more information about

Ethernet connections.

Configuring the System in Measurement &

Automation Explorer (MAX)

Complete the following steps to find the system in MAX.

8| ni.com | NI cRIO-9064 Getting Started Guide

1. Launch MAX on the host computer.

2. Expand Remote Systems in the configuration tree and locate your system.

3. Select your target.

Tip MAX lists the system under the model number followed by the serial

number, such as NI-CRIO-9064-1856AAA.

Setting a System Password

Complete the following steps to set a system password.

Note The default username for the cRIO-9064 is admin. There is no default

password for the cRIO-9064, so you must leave the password field blank when

logging in until you set a system password.

1. Right-click your system and select Web Configuration.

The NI Web-Based Configuration and Monitoring utility opens in your default browser

and is where you set the password. If you have not installed Microsoft Silverlight,

NI Web-based Configuration & Monitoring prompts you to do so.

2. Enter a unique name for your system in the Hostname field.

3. Click the Security Configuration icon.

4. Click Login.

5. In the Login dialog box, enter the username admin and leave the password field blank.

6. Click OK.

7. Click Change Password.

8. Enter and re-enter a new password.

9. Click OK.

10. Click Save.

11. Click OK to confirm you are changing the password.

Caution NI cannot recover lost system passwords. If you forget the password,

you must contact NI and reformat the controller.

Installing Software on the cRIO-9064

Complete the following steps to install software on the cRIO-9064.

1. In MAX, expand your system under Remote Systems.

2. Right-click Software.

3. Select Add/Remove Software to launch the LabVIEW Real-Time Software Wizard.

Tip You must log in if you set a system password.

4. Select the recommended software set for your LabVIEW and NI-RIO Device Drivers

versions.

5. Click Next.

NI cRIO-9064 Getting Started Guide | © National Instruments | 9

6. Select NI Scan Engine from the software add-ons.

Select any additional software to install. If you plan on using the cRIO-9064 with the

LabVIEW FPGA Module, you can click Next. Click NI Scan Engine if you plan on

using the cRIO-9064 without the LabVIEW FPGA Module.

Tip You can use this wizard at anytime to install additional software.

7. Click Next.

8. Verify that the summary of software to install is correct.

9. Click Next to start the installation.

10. Click Finish when the installation is complete.

Troubleshooting the cRIO-9064

The cRIO-9064 is Not Communicating with the

Network

• Ensure that the USB connections between the cRIO-9064 and the host computer and the

Ethernet connections between the host computer and the router are secure.

• Configure the IP and other network settings by completing the following steps.

1. Use a USB A-to-B cable to connect the cRIO-9064 USB device port to a host

computer. The USB driver creates a virtual network interface card and assigns an IP

address to the cRIO-9064 in the format of 172.22.11.x.

2. In MAX, expand your system under Remote Systems.

3. Select the Network Settings tab to configure the IP and other network settings.

4. (Optional) Use the RJ-45 Ethernet port 1 to reconnect the cRIO-9064 to the host

computer. The cRIO-9064 attempts to initiate a DHCP network connection at

powerup.

Note If the cRIO-9064 cannot obtain an IP address, it connects to the

network with a link-local IP address with the form 169.254.x.x. The host

computer communicates with the cRIO-9064 over a standard Ethernet

connection.

• Ensure that you have the correct version of NI-RIO Device Drivers installed on the host

computer. Visit ni.com/info and enter the Info Code swsupport for the minimum

supported versions of LabVIEW and NI-RIO Device Drivers.

Tip If you have recently upgraded LabVIEW, you must reinstall NI-RIO

Device Drivers.

• Ensure that the NI USBLAN adapter is recognized in the Device Manager. On

Windows 7, select Start»Control Panel»Device Manager»Network adapters»National

Instruments»USBLAN adapter. If the USBLAN adapter is not recognized, you must

reinstall NI-RIO Device Drivers.

• Temporarily disable any network firewalls or other security software.

10 | ni.com | NI cRIO-9064 Getting Started Guide

Altri manuali per cRIO-9064

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments NI-7931 Manuale utente

National Instruments

National Instruments NI PXI-8104 Manuale utente

National Instruments

National Instruments NI PXIe-8840 Manuale utente

National Instruments

National Instruments cRIO-9034 Manuale utente

National Instruments

National Instruments AT-GPIB Manuale utente

National Instruments

National Instruments CVS-1457RT Manuale utente

National Instruments

National Instruments NI PXIe-8133 Manuale utente

National Instruments

National Instruments sbRIO-9637 Manuale utente

National Instruments

National Instruments PXI-665 Series Manuale utente

National Instruments

National Instruments IC-3121 Manuale utente

National Instruments

National Instruments NI cRIO-9002 Manuale utente

National Instruments

National Instruments cRIO-FRC II Manuale utente

National Instruments

National Instruments NI cRIO-9036 Manuale utente

National Instruments

National Instruments NI cRIO-9024 Manuale utente

National Instruments

National Instruments GPIB-1284CT Manuale utente

National Instruments

National Instruments IC-3120 Manuale utente

National Instruments

National Instruments FlexRIO NI-7931R Manuale utente

National Instruments

National Instruments GPIB-SCSI-A Manuale utente

National Instruments

National Instruments NI PXI-6653 Manuale utente

National Instruments

National Instruments cRIO-9038 Manuale utente

National Instruments

National Instruments PXIe-8861 Manuale utente

National Instruments

National Instruments IC-3173 Manuale utente

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Manuale utente

National Instruments

National Instruments NI 9514 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

National Instruments cRIO-9064 Manuale utente

Manuali Controllori popolari di altre marche