National Instruments NI PXI-8104 Manuale utente

PXI-1042

INSTALLATION GUIDE

NI PXI-8104

This document contains information about installing the NI PXI-8104

controller in a PXI chassis. For complete configuration and troubleshooting

information (including information about BIOS setup, adding RAM, etc.),

refer to the NI PXI-8104 User Manual. The manual is in PDF format on the

recovery CD included with the controller and on the National Instruments

Web site, ni.com.

Installing the NI PXI-8104

This section contains general installation instructions for the NI PXI-8104.

Consult the NI PXI-8104 User Manual for specific instructions and

warnings.

1. Plug in the chassis before installing the NI PXI-8104. The power cord

grounds the chassis and protects it from electrical damage while you

install the module. (Make sure the power switch is turned off.)

Caution To protect both yourself and the chassis from electrical hazards, leave the chassis

off until you finish installing the NI PXI-8104 module.

2. Remove any panels blocking access to the system controller slot

(Slot 1) in the chassis.

3. Touch the metal part of the case to discharge any static electricity that

might be on your clothes or body.

4. Remove the protective plastic covers from the four bracket-retaining

screws as shown in Figure 1.

5. Make sure the injector/ejector handle is in its downward position.

Align the NI PXI-8104 with the card guides on the top and bottom of

the system controller slot.

NI PXI-8104 Installation Guide 2 ni.com

Figure 1. Removing Protective Screw Caps

Caution Do not raise the injector/ejector handle as you insert the NI PXI-8104. The

module will not insert properly unless the handle is in its downward position so that it

does not interfere with the injector rail on the chassis.

6. Hold the handle as you slowly slide the module into the chassis until

the handle catches on the injector/ejector rail.

7. Raise the injector/ejector handle until the module firmly seats into the

backplane receptacle connectors. The front panel of the NI PXI-8104

should be even with the front of the chassis.

8. Tighten the four bracket-retaining screws on the top and bottom of the

front panel to secure the NI PXI-8104 to the chassis.

9. Check the installation.

10. Connect the keyboard and mouse to the USB connectors. If you are

using a PS/2 keyboard and a PS/2 mouse, use USB-to-PS/2 adapters to

connect both to the USB connectors on the front panel. You may use a

Y-splitter adapter to connect both keyboard and mouse to one USB

port, leaving the other USB ports free for other peripherals, such as a

CD-ROM drive, or secondary hard drive. National Instruments offers

a Y-splitter adapter cable, part number 778713-02, available through

the online catalog at ni.com/products.

1 Protective Screw Cap (4X)

©National Instruments Corporation 3 NI PXI-8104 Installation Guide

11. Connect the DVI monitor video cable to the DVI connector. If you are

using a VGA monitor, use the DVI-to-VGA adapter included with

your kit.

12. Connect peripherals to ports as required by your system configuration.

13. Power on the display. Refer to the NI PXI-8104 User Manual for

details.

14. Power on the chassis.

15. Verify that the controller boots. If it does not boot, refer to the What If

the NI PXI-8104 Does Not Boot? section later in this guide.

Figure 2 shows an NI PXI-8104 controller installed in the system controller

slot of a National Instruments PXI-1042 chassis. You can place PXI devices

in any other slot.

Figure 2. NI PXI-8104 Controller Installed in a PXI Chassis

1 NI PXI-1042 Chassis 2 NI PXI-8104 Controller 3 Injector/Ejector Rail

NI PXI-8104 Installation Guide 4 ni.com

How to Remove the Controller from the PXI Chassis

The NI PXI-8104 controllers are designed for easy handling. To remove

the unit from the PXI chassis:

1. Turn off power.

2. Remove the cables from the controller front panel.

3. Unscrew the bracket-retaining screws in the front panel.

4. Press the injector/ejector handle down.

5. Slide the unit out of the chassis.

What If the NI PXI-8104 Does Not Boot?

Several problems can cause a controller not to boot. Here are some things

to look for and possible solutions.

Things to Notice

• Which LEDs come on? The Power OK LED should stay lit. The

Drive LED should blink during boot as the disk is accessed.

• What appears on the display? Does it hang at some particular point

(BIOS, Operating System, etc.)? If nothing appears on the screen,

try a different monitor. Does your monitor work with a different PC?

If it hangs, note the last screen output that you saw for reference when

consulting National Instruments technical support.

• What has changed about the system? Did you recently move the

system? Was there electrical storm activity? Did you recently add

a new module, memory chip, or piece of software?

Things to Try

• Make sure the chassis is plugged into a working power source.

• Check any fuses or circuit breakers in the chassis or other power

supply (possibly an uninterruptible power supply).

• Make sure the controller module is firmly seated in the chassis.

• Remove all other modules from the chassis.

• Remove any nonessential cables or devices.

• Try the controller in a different chassis or a similar controller in this

same chassis.

• Clear the CMOS. (Refer to the System CMOS section of the

NI PXI-8104 User Manual.)

• Recover the hard drive on the controller. (Refer to the Hard Drive

Recovery section of the NI PXI-8104 User Manual.)

©National Instruments Corporation 5 NI PXI-8104 Installation Guide

For more troubleshooting information, refer to the NI PXI-8104 User

Manual. The manual is in PDF format on the recovery CD included with

your controller and on the National Instruments Web site, ni.com.

What If I Cannot See the Video?

This problem usually results from having the video card output set past the

limits of the monitor. You will need to boot Windows in Safe Mode. To do

this, reboot the controller. As Windows begins to boot, hold down <F8>.

You should now be able to reset the video driver to lower settings. Try

setting the resolution to 640 × 480 and the refresh rate to 60 Hz. Once you

reboot, you can raise these values again, using the test option in Windows.

These settings are accessible through the Advanced tab of the Display item

in the Control Panel. Alternately, you can try a different monitor,

preferably a newer and larger one.

If the system has been booted to Windows without a monitor attached, the

driver may have defaulted to the video output connector being disabled.

Press <Ctrl-Alt-F1> to re-enable the video display in Windows. Press

<Ctrl-Alt-F4> to re-enable a DVI display. For more information, refer

to KnowledgeBase 3OHCFRD8 at ni.com/support.

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or

ni.com/patents.

Altri manuali per NI PXI-8104

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments CMS-9068 Istruzioni di montaggio

National Instruments

National Instruments PCI-7352 Manuale utente

National Instruments

National Instruments cDAQ-9132 Manuale utente

National Instruments

National Instruments 9862 Manuale utente

National Instruments

National Instruments 73 Series Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9066 Manuale utente

National Instruments

National Instruments cDAQ-9133 Manuale utente

National Instruments

National Instruments sbRIO-9860 Manuale utente

National Instruments

National Instruments NI cRIO-9035 Manuale utente

National Instruments

National Instruments PXI Express Series Manuale utente

National Instruments

National Instruments PXI-8195 Manuale utente

National Instruments

National Instruments GPIB-1284CT Manuale utente

National Instruments

National Instruments cRIO-9037 Manuale utente

National Instruments

National Instruments NI PXIe-8135 Manuale utente

National Instruments

National Instruments GPIB-ENET Series Manuale utente

National Instruments

National Instruments sbRIO-9638 Manuale utente

National Instruments

National Instruments NI-488.2 Manuale utente

National Instruments

National Instruments PXI-8109 Manuale utente

National Instruments

National Instruments sbRIO-9608 Manuale utente

National Instruments

National Instruments PCI-7330 Manuale utente

National Instruments

National Instruments cRIO-9064 Manuale utente

National Instruments

National Instruments DAQ-STC Series Manuale del prodotto

National Instruments

National Instruments NI cDAQ-9134 Manuale del proprietario

National Instruments

National Instruments GPIB-232 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente