Nautel NX100 Manuale utente

NX100 Transmitter

Installation Manual

Document:NHB-NX100-INS

Issue: 3.2 2017-03-31

Status: Standard

Nautel Limited

10089 Peggy’s Cove Road

Hackett’s Cove, NS Canada B3Z 3J4

Phone: +1.902.823.3900 or

Toll Free: +1.877.6NAUTEL (6628835) (Canada & USA only)

Fax: +1.902.823.3183

Nautel Inc.

201 Target Industrial Circle

Bangor, Maine USA 04401

Phone: +1.207.947.8200

Fax: +1.207.947.3693

Customer Service (24 hour support)

+1.877.628.8353 (Canada & USA only)

+1.902.823.5100 (International)

Email: [email protected]

Web: www.nautel.com

The comparisons and other information provided in this document

have been prepared in good faith based on publicly available

information. The reader is encouraged to consult the respective

manufacturer's most recent published data for verification.

© Copyright 2017 NAUTEL. All rights reserved.

NX100 Installation Manual Table of contents

Page v

Contents

Release control record vii

Preparing for installation 1-1

Unpacking and positioning 2-1

Connecting transformer taps/load wiring 3-1

Connecting the station reference ground 4-1

Connecting ac power 5-1

Adjusting the spark gap 6-1

Installing audio inputs 7-1

Planning complete? 7-1

Routing cables 7-1

Setting Exgine audio parameters 7-4

Installing control/monitor wiring 8-1

Planning complete? 8-1

Routing cables 8-1

Commissioning tasks 9-1

Pre-commissioning tasks 9-1

Commissioning 9-3

Going on-air 9-6

NX100 Installation Manual Table of contents

Page vi Issue 3.2 2017-03-31

Parts and tools 10-1

Contacting Nautel 10-1

Parts supplied by Nautel 10-1

Parts not supplied by Nautel 10-2

Parts ordering 10-2

Module replacement program 10-2

Tools for installation 10-3

Pre-installation / Installation assistance 11-1

Pre-installation consulting 11-1

Installation and commissioning service 11-1

Online documentation 11-3

On-site support 11-3

Training 11-3

Standard warranty 11-4

Extended warranties 11-8

List of terms 12-1

NX100 Installation Manual

Issue 3.2 2017-03-31 Page vii

Release control record

Issue Date Reason

3.0 2012-11-01 Release 3 of product (NARA52B)

3.1 2016-02-08 Section 9, sub-paragraphTurning on theTransmitter:

improved and added various steps.

Section 9, sub-paragraph Modulation Checks: added

NOTE after step 4 to maintain positive and negative

modulation peaks within specification.

3.2 2017-03-31 Section 2: improved and added various steps.

Section 3: added clarification about phase

connections and taps on transformer windings.

Section 6: updated Table 6.1.

NX100 Installation Manual

Page viii Issue 3.2 2017-03-31

NX100 Installation Manual Preparing for installation

Issue 3.2 2017-03-31 Page 1-1

Section 1: Preparing for installation

Before installing your NX100 transmitter, perform the following steps:

1. Ensure that you have performed the pre-installation tasks described in the

NX100 Pre-installation Manual.

2. Make sure that you received all the components. (Check your packing list.)

3. Inspect all crates and packages for damage.

4. Report any damage immediately to your Nautel sales representative and the carrier.

5. Move the crates as close as possible to the transmitter’s planned location.

6. Unpack the crates in accordance with the instructions provided on the outside of the crates.

• For each crate, remove the panel labelled open this side. The panel is attached using

Philips head screws.

• Remove any visible packing material, including braces, from the crate's interior.

7. Review any assembly notes or instructions contained inside the transmitter crates. (For sites

requiring custom configurations, the instructions provided with the transmitter replace the

instructions provided here.)

8. Gather the parts and tools you will need for installation. For a list of required tools, see

“Parts and tools” on page 10-1.

9. When you are ready to install the NX100 transmitter, follow the steps shown in Figure 1.1

on page 1-2.

TIP When you have completed a task or step, put a check mark beside the step

number.

CAUTION:

FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S

WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.

NX100 Installation Manual Preparing for installation

Page 1-2 Issue 3.2 2017-03-31

Figure 1.1: Flowchart - Installing the transmitter

Unpacking and positioning - see page 2-1

Connecting the station reference ground - see page 4-1

Connecting transformer taps/load wiring - see page 3-1

Installing control/monitor wiring - see page 8-1

Commissioning tasks - see page 9-1

Perform operational tasks:

“Commissioning”, “Modulation checks” and “Going on-air”, beginning on page 9-3

Connecting ac power - see page 5-1

Installing audio inputs - see page 7-1

Adjusting the spark gap - see page 6-1

Altri manuali per NX100

3

Indice

Altri manuali Nautel Trasmettitore

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente