Nautel NX300 Manuale utente
NX300 Transmitter
Installation Manual
Document:NHB-NX300-INS-3.0
Issue: 3.0 2012-11-01
Status: Standard
Nautel Limited
10089 Peggy’s Cove Road
Hackett’s Cove, NS Canada B3Z 3J4
Phone: +1.902.823.3900 or
Toll Free: +1.877.6NAUTEL (6628835) (Canada & USA only)
Fax: +1.902.823.3183
Nautel Inc.
201 Target Industrial Circle
Bangor, Maine USA 04401
Phone: +1.207.947.8200
Fax: +1.207.947.3693
Customer Service (24 hour support)
+1.877.628.8353 (Canada & USA only)
+1.902.823.5100 (International)
Email: [email protected]
Web: www.nautel.com
The comparisons and other information provided in this document
have been prepared in good faith based on publicly available
information. The reader is encouraged to consult the respective
manufacturer's most recent published data for verification.
© Copyright 2012 NAUTEL. All rights reserved.
NX300 Installation Manual Table of contents
Page v
Contents
Release control record vii
Preparing for installation 1-1
Unpacking and positioning 2-1
Completing cabinet assembly 3-1
Connecting transformer taps/load wiring 4-1
Connecting the station reference ground 5-1
Connecting ac power 6-1
Adjusting the spark gap 7-1
Installing audio inputs 8-1
Planning complete? 8-1
Routing cables 8-1
Setting Exgine audio parameters 8-4
Installing control/monitor wiring 9-1
PLanning complete? 9-1
Routing cables 9-1
Commissioning tasks 10-1
Pre-commissioning tasks 10-1
Commissioning 10-2
NX300 Installation Manual Table of contents
Page vi Issue 3.0 2012-11-01
Going on-air 10-4
Parts and tools 11-1
Contacting Nautel 11-1
Parts supplied by Nautel 11-1
Parts not supplied by Nautel 11-2
Parts ordering 11-2
Module replacement program 11-2
Tools for installation 11-3
Pre-installation / Installation assistance 12-1
Pre-installation consulting 12-1
Installation and commissioning service 12-1
Online documentation 12-3
On-site support 12-3
Training 12-3
Standard warranty 12-4
Extended warranties 12-7
List of terms 13-1
NX300 Installation Manual
Issue 3.0 2012-11-01 Page vii
Release control record
Issue Date Reason
3.0 2012-11-01 Release 3 of product (NARA54B)
NX300 Installation Manual
Page viii Issue 3.0 2012-11-01
NX300 Installation Manual Preparing for installation
Issue 3.0 2012-11-01 Page 1-1
Section 1: Preparing for installation
Before installing your NX300 transmitter, perform the following steps:
1. Ensure that you have performed the pre-installation tasks described in the
NX300 Pre-installation Manual.
2. Make sure that you received all the components. (Check your packing list.)
3. Inspect all crates and packages for damage.
4. Report any damage immediately to your Nautel sales representative and the carrier.
5. Move the crates as close as possible to the transmitter’s planned location.
6. Unpack the crates in accordance with the instructions provided on the outside of the crates.
• For each crate, remove the panel labelled open this side. The panel is attached using
Philips head screws.
• Remove any visible packing material, including braces, from the crate's interior.
7. Review any assembly notes or instructions contained inside the transmitter crates. (For sites
requiring custom configurations, the instructions provided with the transmitter replace the
instructions provided here.)
8. Assemble your parts and tools.
For a list of required tools, see “Parts and tools” on page 11-1.
9. When you are ready to install the NX300 transmitter, follow the steps shown in Figure 1.1
on page 1-2.
TIP When you have completed a task or step, put a check mark beside the step
number.
CAUTION:
FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S
WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.
NX300 Installation Manual Preparing for installation
Page 1-2 Issue 3.0 2012-11-01
Figure 1.1: Flowchart - Installing the transmitter
Unpacking and positioning - see page 2-1
Connecting the station reference ground - see page 5-1
Connecting transformer taps/load wiring - see page 4-1
Installing control/monitor wiring - see page 9-1
Commissioning tasks - see page 10-1
Perform operational tasks:
“Commissioning”, “Modulation checks” and “Going on-air”, beginning on page 10-2
Connecting ac power - see page 6-1
Installing audio inputs - see page 8-1
Adjusting the spark gap - see page 7-1
Completing cabinet assembly - see page 3-1
Altri manuali per NX300
1
Indice
Altri manuali Nautel Trasmettitore
Nautel
Nautel VS1 Manuale utente
Nautel
Nautel NX400 Manuale utente
Nautel
Nautel ND2000A-02x-xx0 Series Manuale del proprietario
Nautel
Nautel XR6 Manuale di programmazione
Nautel
Nautel NV7.5 Manuale utente
Nautel
Nautel VX150 Manuale
Nautel
Nautel NX50 Manuale utente
Nautel
Nautel NV5 Manuale di programmazione
Nautel
Nautel GV30N Manuale di programmazione
Nautel
Nautel VS300 Manuale utente
Nautel
Nautel NX100 Manuale utente
Nautel
Nautel J1000 Manuale utente
Nautel
Nautel GV40 Manuale utente
Nautel
Nautel NV10LT Manuale utente
Nautel
Nautel VX150 Manuale utente
Nautel
Nautel XR12 Manuale di programmazione
Nautel
Nautel FM10011 Manuale utente
Nautel
Nautel J1000 Istruzioni operative
Nautel
Nautel VS1 Manuale utente
Nautel
Nautel XR12 Manuale utente
